iMARC Pet Tag Engraver User manual

Tigger
More than
2,000 tags
to choose from!
Pet Tag Engraver
USER MANUAL
MAX
Beware of Dog

Table of Contents
Machine Labels ..................................1
Getting Started ....................................2
Set-up ...................................................3
Holder Installation & Setup.................4
Engraving a Tag ..................................6
Engraving Text .....................................8
Engraving Clip Art ............................ 14
Engraved Tag Counts ...................... 15
Changing Engraving
Pressure & Languages....................16
International Characters ................. 17
Clip Art............................................... 19
Software License Information ......... 21
Table of Contents

1
Machine Labels
100-240 VAC
50/60 Hz 1 Amp
The lightning bolt symbol refers to the hazardous
voltage inside the machine. Injury can occur.
Do not attempt to service the machine when
plugged into a power source.
100-240 volts
Frequency is 50/60 Hertz
1 Amp
These labels identify the hazards of opening the
machine while in use. Keep hands and clothing
away from moving parts inside the door to
prevent injury and mechanical hazards. Please
refer all servicing to qualied personnel.

2
Electrical Receptacle
The power cord is
inserted here
USB Ports
Cooling Fan Cover
Easily removable for
access to the filter
Ethernet
Port
Getting Started
Before plugging in the iMARC, familiarize
yourself with the machine.
The On/
Off switch is
located on
the front of the
machine.

3
Setting up your iMARC is quick and easy.
Plug the keyboard into a USB port.
To power on the iMARC,
press the on/off switch.
Plug the power cord into the electric
receptacle.
Plug the cord into any standard (110
or 220 Volt) outlet, and switch on the
machine.
IMPORTANT: Earlier version iMARC machines must have the correct
voltage plugged in to them. Please follow the voltage requirement
label on machine for correct power needed.
Set-up

4
Holder Install & Setup
Once powered on, it is now time to install the
holders. Holders need to be installed on the
engraving table during HOLDER SETUP.
Engraving Table-
No holders installed
Engraving Table-
With holders installed
Tag Holder
This is the rst screen
you will see. This is the
INTRODUCTION SCREEN.
From the INTRODUCTION SCREEN, press F4
for holder setup.
Note: Holders can only be installed when you are in the HOLDER SETUP
screen. Attempting to install them at any other time could result in
damage to the holders or the machine.

5
The holder setup is simple. Follow the
on screen instructions as well as the
steps on this page.
This is the HOLDER
SETUP screen.
Insert your holder on the engraving table.
Position the holes in the holder directly over
the pins in the engraving table, and move
the holders directly up and down over the
pins. It may be a snug t, so apply light
pressure as needed.
Press the up and down
arrow keys to select the
installed holder.
Then press ENTER.

6
Engraving a Tag
Engraving a tag is quick and easy.
Each step is clearly stated in the
on-screen instructions.
From the INTRODUCTION SCREEN,
press any key to get started.
Note: After a period without
keystrokes, the machine will reset to
this screen.

7
In the TAG SELECTION screen, use the up
and down arrow keys to scroll through the
available tags.
Note: If a specic tag does not appear on
the screen, press F4 to return to HOLDER
SETUP and install the correct holder.
(See pg. 4 for instructions)
Press Escape to
quit…
Press Enter to
Continue…

8
After selecting a tag,
choose the type style.
From the SELECT
FONT screen, choose
the desired type
style by pressing the
corresponding number
on the keyboard.
Note: Pressing ENTER
will select the “iMARC
BLOCK” type style.
Press Esc to return to the TAG
SELECTION screen.
8 For clip art. 9 For sample
or your logo.
Clip art and optional logo function
To engrave clip art onto iMARC tags, press “8”
and turn to page 14 for additional instructions. If
the iMARC has company logos stored in it, press
“9” to select the logo and enter the letter A on
the text entry screen to engrave it.
Engraving Text