IMG LIGHTING FLORIS GOBO S User manual

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
FLORIS GOBO S
USER MANUAL

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
188
454
199
198
1 PRODUCT
1.1 DIMENSIONS

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
1.2 Safety Notes
IMPORTANT
．．．．．．．．．
This product must be installed by a qualified professional.
In order to maintain this condition and to ensure a safe operation, it is absolutely necessary
for the user to follow the safety instructions and warning notes
The manufacturer will not accept liability for any resulting damages caused by the
non-observance of this manual or any unauthorized modification to the device.
CAUTION!
．．．．．．．．
Make sure that the available voltage is not higher than stated on the rear panel.
Do not touch the power cables if your hands are wet.
The earth wire must always be connected to the ground. Therefore it is essential to connect
the yellow/green conductor to earth.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the
device and the power-cord from time to time. The electric connection, repairs and servicing
must be carried out by a qualified employee.
Always disconnect power input cable to completely remove power from unit when not in use
or before cleaning or servicing the fixture.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
The surface of the product’s casing can reach up to 70° C (158° F) during operation. Avoid
contact by persons and materials. Do not install the product in a location where there is a risk
of accidental contact. Allow the product to cool for at least 10 minutes before handling.
For replacement use lamps and fuses of same type and rating only.
Please protect the fixture and avoid destroy during transport and installation. If there is any
damage to the coating, the shell may be corroded.
When hanging lamps and lanterns, it is necessary to verify that facilities and hooks can bear
at least 10 times the weight of lamps and lanterns.
Fix the safety rope at the correct holes only. Only operate the fixture after having checked
that the housing is firmly closed and all screws are tightly fastened.
The maximum ambient temperature 45°C must never be exceeded. Do not operate the
product if the ambient temperature (Ta ) exceeds 45° C (115° F).
The minimum ambient temperature (Ta min.): -40° C
When the temperature reaches the above upper limit, the fixture regulates output to protect
from overheating.
E
．
lectrical
．．．．．．．．．
W
．
arning
．．．．．．
The light source contained in this luminaire shall only be replaced by the manufacturer or his
service agent or a similar qualified person.

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
2 INSTALLATION
2.1 MOUNTING
The fixture can be mounted in any position.
Always ensure that mounting surface can withstand 10 times the weight of the fixture.
A lways use a safety cable when mounting the fixture in any elevated position.
UPRIGHT HANGING
2.2 POWER CONNECTIONS
This product has an auto-ranging power supply that can work with an input voltage range of
100–240 VAC, 50/60 Hz.
AC Plug
Connection Wire (U.S. Wire(Europe) Screw Color
AC Live Black Brown Yellow/Brass
AC Neutral W hite Blue Silver
AC Ground Green/Yellow Green/Yellow Green

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
2.3 Power connections
T his product provides f or t he u se o f input power and s ignal cables a re t hree-core,the
connection diagram is as follows
2.4 Signal connections
I f the signal cable i s over 60m b etween the DMX512 controller and fixture or beween two
fixtures, then a DMX signal amplifier is needed as well.

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
3 FUNCTIONS AND SETTINGS
3.1 DISPLAY OPERATION
MENU：Used to access the menu or to return a previous menu option;
ENTER：Used to select and store the current menu or confirm the current function value
or
option within a menu;
UP：Navigates downwards through the menu list and increases the numeric value when in
a
function;
DOWN：Navigates upwards through the menu list and decreases the numeric value when i
n
a function；
3.2 Menu Map
ADDRESS 001-512（default 001） DMX address setting
PERSON STANDARD（default） Use the menu to select desired
channel mode
BASIC
RUN
MODE
DMX512（default） Select Signal
AUTO
EDIT1
EDIT2
OPTION DIMMER DIM4（default） Dimming curves DIM1 (fast) to DIM4
(slow)；
OFF
DMX
ERROR
SAVE（default） Hold after loss of DMX signal
BLACK Blackout after loss of DMX signal
PWM 1200HZ（default） Sets the PWM frequency
2400HZ
4000HZ
6000HZ
25000HZ
PERFORM LIVE（default） Automatic rotation of fan
POWER Fast rotation of fan，all power
STUDIO Fan mode low speed
DISP KEY ON（default） Press menu for 5 seconds to input up,
down, up ,down
OFF
DISP TIME ON Turns off display backlight after
10s/30s/2min of inactivity
10s
30s（default）
2min
LOAD
PARA
NO（default） Upload data
YES Not upload data
SETTING RECOVERY **** Restore default factory settings.

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
CLEAN EDIT1 **** Clean customer self-editing scene 1
CLEAN EDIT2 **** Clean customer self-editing scene 2
WDMX
RESET
NO（default） Clear the receiver's message
YES Do not clear the receiver's message.
SIGNAL ONLY XLR（default） ONLY XLR is wire only
XLR FIRST XLR FIRST is wire first
ONLY WDMX ONLY WDMX is wireless only
WDMX FIRST WDMX FIRS is wireless first
WDMX TO DMX WDMX TO DMX is wireless to wired
LANGUAG
E
CHINESE LANGUAGE
ENGLISH（default）
EDIT EDIT 1-2 STEP(01-30) COLOR 0-255 Edit the custom programs1-30
Select play 【EDIT 1】 in RUNMOEDE
CUSTOM 1; Select play 【EDIT 2】 in
RUNMOEDE CUSTOM 2
ROTA GOBO 0-255
GOBO ROTA 0-255
ANIMATION 0-255
ANIMA_ROT 0-255
PRISM 0-255
ZOOM 0-255
FOCUS 0-255
DIMMER 0-255
STROBE 0-255
TIME 0-255 0-255( Multiply by 0.1s )
USE YES/NO Run the program
MANUAL AUTO TEST Automatic Testing
MANUAL
TEST
COLOR 0-255 Manual control channel
ROTA GOBO 0-255
GOBO ROTA 0-255
ANIMATION 0-255
ANIMA_ROT 0-255
PRISM 0-255
ZOOM 0-255
FOCUS 0-255
DIMMER 0-255
STROBE 0-255
DEBUG
HIDE
YES Factory testing mode. All stepper
motors are not controlled by signal, It
only works again after the reset.
NO
RESET ALL RESET Select Yes/No to carry out all reset
COLOR SYSTEM COLOR/GOBO/ROTA GOBO reset

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
ZOOM/FOCUS SYSTEM
ZOOM/FOCUS reset
OTHER
INFO F IXTURE HOURS
Hours of fixture use
TEMPERATURE
LED temperature
VERSION
Software versions
RDM
RDM information
SYSTEM
ERROR
Memory IC
Memory IC
Angle Sensor
Angle Sensor
Temperature
Temperature
Color Reset
Color Reset
RGOBO Reset
RGOBO Reset
GOBOR Reset
GOBOR Reset
Animation Reset Animation Reset
Prism Reset
Prism Reset
Zoom Reset
Zoom Reset
Focus Reset
Focus Reset
SERVICE **** COLOR ±127
Color position fine adjustment
ROTA. GOBO ± 127
Rotate Gobo position fine adjustment
GOBO.ROTA ±127
Self-rotation position fine adjustment
ANIMATION ±127
Animation position fine adjustment
PRISM ±127
Prism 1 position fine adjustment
FOCUS ± 127
Focus position fine adjustment
ZOOM ± 127
Zoom position fine adjustment
All passwords of this product are <UP>, <DOWN>,<UP>, <DOWN>, <ENTER>)

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
4 USING A DMX512 CONTROLLER
4.1 DMX CONTROL
BASIC
(11CH)
STANDARD
(CH14) VALUE FUNCTION
1 1 0-255 Dimmer
-- 2 0-255 Dimmer fine
2 3
STROBE
0-9 NO FUNCTION
10-99 STROBE（ FROM SLOD TO FAST ）
100-109 NO FUNCTION
110-179 LIGHTNING STROBE
180-189 NO FUNCTION
190-255 RANDOM SROBE
3 4
COLOR WHELL 5+1
000-007 White
008-015 Color 1
016-023 Color 2
024-031 Color 3
032-039 Color 4
040-047 Color 5
048-191 Color Wheel 0-360°
192-222 Color Wheel Rainbow Effect(Speed 100%->1)
223-224 Stop
225-255 Color Wheel Rainbow Effect (Speed 1->100%)
- 5 000-255 COLOR WHIELL FINE
4 6
ROTATING GOBO 4+1
000-010 ROTATING WHITE
011-024 ROTATING GOBO 1
025-038 ROTATING GOBO 2
039-052 ROTATING GOBO 3
053-066 ROTATING GOBO 4
067-080 ROTATING GOBO 1 SHAKE (SPEED 1 —> 100%)
081-094 ROTATING GOBO 2 SHAKE (SPEED 1 —> 100%)
095-108 ROTATING GOBO 3 SHAKE (SPEED 1 —> 100%)
109-122 ROTATING GOBO 4 SHAKE (SPEED 1 —> 100%)
123-127 WHITE
128-190 ROTATING GOBO FLOWING WATER EFFECT (SPEED 100 —> 1%)
191-192 STOP WATER EFFECT
193-255 ROTATING GOBO FLOWING WATER EFFECT(SPEED 1 —> 100%)
5 7
GOBO ROTATING
0-120 ROTATING GOBO ANGLE ADJUSTMENT (0 —> 360°)
121-125 STOP
126-165 ROTATING GOBO SHAKE (SPEED 1 —> 100%)

TO CREATE IMPRESSIVE RESULTS
img-lighting.ru
[email protected]
166-170 STOP
171-210 ROTATING GOBO POSITIVE ROTATION (SPEED 100% —> 1)
211-215 STOP
216-255 ROTATING GOBO REVERSE ROTATION (SPEED 1 —> 100%)
6 8 Dynamic Effect wheel Location
0-255 Dynamic Effect wheel Location
7 9
Dynamic Effect wheel Autorotation
0-10 White
11-131 Dynamic Effect Wheel Flow Effect, Clockwise, fast to slow
132-134 Stop
135-255 Dynamic Effect Wheel Flow Effect, Anticlockwise, slow to fast
8 10
PRISM
0-10 WHITE
11-155 PRISM INSERT AND ADJUST THE ANGLE (0 —> 360°)
156-157 STOP
158-205 PRISM INSERT AND POSITIVE ROTATION (SPEED 100% —> 1)
206-207 STOP ROTATION
208-255 PRISM INSERT AND REVERSE ROTATION (SPEED 1 —> 100%)
9 11 0-255 ZOOM
10 12 0-255 FOCUS
-- 13 0-255 FOCUS FINE
11 14
CONTROL（
（
EXECUTE AFTER 3 SECONDS）
）
000-010 NO FUNCTION
011-060 RESERVED
061-070 LIVE
071-080 STUDIO
081-090 POWER
091-100 RESERVED
101-110 DIMMER OFF
111-120 DIMMER DIM4
121-150 RESERVED
151-160 1200Hz
161-170 2400Hz
171-180 4000Hz
181-190 6000Hz
191-200 25000Hz
201-210 ALL RESET
211-220 COLOR/GOBO/ROTA GOBO reset
221-230 ZOOM/FOCUS RESET
231-240 PRISM/EFFECT WHEEL RESET
241-255 RESERVED