WE-EF ETC320-GB LED User manual

WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Inground Luminaire
ETC320-GB LED
Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges, it is essential to cover mains supply and data input
lines at the distribution board level, by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation. Also, disconnect luminaires
before operating high-power devices such as, for example, electrical
arc welders.

1
IP69, Class I, ta = 25°C
:
<
;
<
-
O
p
e
n
L
o
c
k
-
>
<
-
O
p
e
n
L
o
c
k
-
>
Fig. I
Inground Luminaire
355º
ø 160
ø 350
180
0º-20º

2
Light Source
LED
Maintenance
Warning: Do not open luminaire while mains supply is switched on.
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
2) Remove cover and lens/gasket assembly. Clean all surfaces and ensure that threaded entries are free
from dirt by using a wet cloth with mild detergent.
3) Check gasket for damage and replace if necessary.
Attention: In case of damage to the lens, the complete lens/gasket assembly must be replaced.
4) In case of damage to the LED, the complete gimbal module Xmust be returned to WE-EF for factory-
maintenance (contact your authorised WE-EF agent for service). To remove the gimbal module proceed
as follows (Fig. I):
a) Rotate wheel W(using a standard tool) in the direction of the 'open' mark until the gimbal module can
be pulled out of the luminaire housing.
b) Detach terminal connector Yand remove gimbal module X.
c) Properly package gimbal module Xand return to WE-EF for factory-maintenance.
Attention: During the factory-maintenance period, ensure both the luminaire cover and lens are secured
in position.
5) To install gimbal module X, attach terminal connector Y. Set gimbal module Xinto luminaire housing.
Rotate wheel Win the direction of the 'lock' mark until gimbal module XLVĥUPO\VHFXUH)ROORZVWHSV
11-16 to close the luminaire (see: Phase Two – Luminaire Installation, Electrical Connection, and Aiming
Procedure).
Damaged mains supply cable: Contact your authorised WE-EF agent for replacement.

3
Installation
The product must be installed and maintained
E\DVXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFH
with latest building/construction and/or electrical
regulations and relevant legislation.
Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWR
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full
responsibility of the modifying person/organisation.
Claims based on defects attributable to improper
installation and/or application, and the consequences
thereof, are excluded.
Installation Methods
For proper installation, use the supplied installation
blockout.
Ensure that proper drainage is provided for
the shown installation methods:
In landscape/paved areas, sand or concrete with
gravel base (Fig. I).
With fully concreted installation, drainage piping
must be provided (Fig. II).
Fig. III
Fig. II

4
Phase One
Blockout Installation Procedure
(during earth or masonry work)
1) Ensure that proper drainage is provided for the
shown installation methods.
2)
Ensure a suitable recess is provided to accommodate
installation blockout/mounting ring assembly L/H.
3) Test drainage (ensure water drains within 30 mins,
Warning: warranty void if luminaire installed
without appropriate drainage).
4) Set installation blockout/mounting ring assembly
L/H in position and ensure that:
a) Arrow Ron mounting ring His pointed towards
the object to be illuminated (wall, tree, column).
b) Mounting ring HLVĦXVKZLWKVXUIDFHF.
,IWKHĦRRUZLOOEHWLOHGRUSDYHGDIWHUZDUGVOHDYH
an appropriate gap.
c) Mains supply cable(s) OLVRIVXĩFLHQWOHQJWK
to connect sealable junction box Jwith cable N
from luminaire.
5) During ongoing earth and/or masonry works,
do not remove screws M from mounting ring H.
Ensure that installation blockout/mounting ring
assembly L/H is not damaged and has maintained
its original shape. If necessary use a cover plate.
6) Framing should be installed to prevent vegetation
from growing over the lens.

5
Aiming of gimbal
14)Insert a standard tool into a slot on locking wheel
W. Rotate locking wheel Win the ‘OPEN’ direction
until gimbal can be moved (Fig. V).
To horizontally aim the gimbal
(Rotation 355°)
+ROGĥQVEto rotate the gimbal.
To vertically aim the gimbal
(Tilt 0-20°)
a) Insert screw driver into hole T.
b) Adjust gimbal to desired angle
(Refer to protractor scale U).
Note: Angle can be adjusted in 2° increments.
15)Insert screw driver into a slot on locking wheel W.
Rotate locking wheel Win the ‘LOCK’ direction
XQWLOWKHJLPEDOLVĥUPO\VHFXUHG)LJ9
Warning: Do not tighten more than necessary to
secure gimbal.
16)Ensure that all surfaces are clean and dry.
Reposition lens/gasket assembly B, cover Aand
screws Don luminaire housing C.
Note: Ensure that orientation pin Pis align with
hole Qin gasket (Fig. VI).
17)Switch on mains electrical supply and operate
light source for approximately 30 minutes to dry
any moisture.
Attention: 'RQRWVZLWFKRĪ/('EHIRUHOXPLQDLUH
is properly sealed.
18)Secure cover Aas follow:
a) Partially secure screws Din criss-cross
sequence (Fig. VII) starting from position 1.
b) Tighten screws Din same sequence.
c) Fully tighten screws Din same sequence again,
using torque 3 Nm.
Phase Two
Luminaire Installation, Electrical Connection, and
Aiming Procedure
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
8) Check that rating shown on luminaire label
conforms with mains electrical supply.
9) Remove screws Mfrom mounting ring H.
10)Terminate cable N and mains supply cable O
in sealable junction box J and connect leads to
respective terminals:
a) ON/OFF or wireless (L = Phase, N = Neutral,
= Earthing)
b) 1-10 V/DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line,
D–/D+ = 1-10 V control line).
Please refer to instruction inside SJB packaging.
11)Remove cover Aand lens/gasket assembly Bby
loosening screws D.
12)Set cables and sealable junction box Jinside
installation blockout L.
13)Place luminaire housing Cinto installation
blockout/mounting ring assembly L/H. Secure
luminaire with mounting ring Hby tightening
screws M.
Warning:
When luminaire is placed inside
installation
blockout L, ensure there is no stress on
sealable junction box Jor electric cables (Fig. IV).

6
D
N
O
A
C
B
F
R
J
O
M
+
L
Fig. IV
M
F
C
J
L
N
H

7
Fig. V

-
O
p
e
n
L
o
c
k
-
!
T
8
*
E
W
Fig. VI
P
Q
Fig. VII
1
3
2
4

TO9191W0823 © WE-EF 2023
7HFKQLFDOVSHFLĥFDWLRQVDUH
subject to change.
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[email protected]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[email protected]
WE-EF SWITZERLAND
Switzerland
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[email protected]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]