Impact Acoustics chatpod 185 User manual

chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland, 180620
20min
ASSEMBLY
INSTRUCTIONS
chatpod 185

2chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Scope of delivery
1xA1xG
6xH
1xI
1xJ
4xK
7x
6.3x70mm
L
M6x40mm
12xM
1x
C
1xD
1xE
1xF
1xB

3chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
What you’ll need in addition
How the parts come together
1x2x 1x
E
C
F
D
G
G
L
4mm 2x 3mm 1x 13mm 1x2.5mm 1x

4chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
M
M
H
A
B

5chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Always carry the front panel (A) in a way that the hinges are always on top, otherwise
the door could accidentally open and break.
Attention

6chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Assembly instructions
step 1
Put the honeycomb cardboard blocks (K) under the base plate (F). Make sure that
the base plate (F) sits well on the blocks (K).
K
K
K
K
F

7chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
1.
Step 2
Place the sides (C),(D) on the blocks (K) and press them into the base plate (F). This
should go smoothly if not, make sure the sides (C),(D) are aligned with the base plate (F).
C D
2.

8chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 3
Remove from the cover (E) the outer cladding and the honeycomb cardboard piece and
lay it aside.
1.
2.
E

9chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 4
Put the cover (E) on both sides (C),(D) and make sure they are flush on both sides. The
cover (E) should slide in smoothly. The Cable which you can see in the second image
should stand out.
1.
2.

10 chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 5
Pull down the cover (E) and tighten the screws (L) at the same time. Remove the two
screws (2.) for the table.
LL
1.
2.
1.1.

11 chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 6
Align the table (G) to the five holes and secure it with the screws (L). Attache the Smart-
phone holder (J) to the sheet metal .
G
J
L
L
2.
3.
1.

12 chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 7
Insert the rods (H) in the sides.
H
H
H
H
H
H

13 chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 8
Push the back wall (B) in the sides, the base plate and the cover. The honey combe card-
board and chipboard should slide smoothly in the grove from the back wall (B) other-
wise try to align it to each other. Insert the screws (M) and tighten hem slightly. Proceed
the same way with the front panel (A). Now tighten the screws (M) firmly they must be
locked from the other side.
M
M
M
M
M
M
M
M
M
A
B
1.
3.
4.
2.

14 chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 9
Mount the door handle (I) in the following order: lock, metal ring, plastic ring, door handle.
Press the two door handles together while tightening the set screw with the 3 mm Allen
wrench.
I
I

15 chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
A
A
B
B
C
C
D
D
Step 10
Plug in the cable. insert the honey combe cardboard and the top part of the cover.
Note: Only the power cable has to
be plugged in the other cables are
already plugged in.
motionsensor
fan
power in
light
1.
3.
2.

16 chatpod 185 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Lucerne, Switzerland chatpod
Step 11
Remove the honeycomb cardboard blocks (K) and recycle them. Check with a level if the
floor plate is levelled if not, rotate the levelling feet until it is. Plug in the cable.
Well done!
1.
1.3.
3.
3.
4.