Impact Acoustics Chatpod 700 User manual

IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Chatpod 700
90min
Assembly instructions
Chatpod 700

2Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 1
Press the drive-in nuts (AD) on the inside of the back panel (E and F) into the holes
and tighten the screws (Y) with the 4mm hex key (AJ).
E
F
AD
Y

3Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 2
Insert the dowels (AE) in the four holes. Join the two frame halves (E and F). Place the
three connectors (W) in the cut-outs and tighten them with the 4 mm hex key (AJ).
E
F
W
W
W
AE
AE

4Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 3
Remove the silicone paper from the double-sided tape on the back of the two panels (O)
and press the fillings into the recess of the back panel.
O
O

5Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 4
Position the back panel to the final position and level it using the four leveling feet with
a 13 mm wrench.

6Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 5
Place the blocks (V) on the floor and place the base plate (L) on top. Plug the cable
(AH) with the power plug into the H-connector (AG). Insert also the plugs of the left
(C) and right side (D) into the connector and make sure that the plugs snap in.
click
click
click
C D
L
VV
V
V
AG
AH
6
5
5
7
8
8

7Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 6
Place the base plate (L) on the four blocks (V) and make sure that they are aligned
as shown. Join the two sides (C and D) with the base plate (L). This should go easily,
otherwise the parts must be aligned better to each other.
6
5
5
7
8
8
C D
L
2.
1.
2.

8Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
90º 90º
Step 7
Guide the cable of the side through the recess of the cover (N). Join the cover with the
two sides. This should go without too much resistance.
6
6
5
5
7
7
8
8

9Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 8
Move the two sides, the bottom and the cover into the back panel. It may be necessary
to lift the cover slightly. Make sure that the cable is exposed.

10 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 9
Screw one setscrew (AB) into each connecting rod (S) using the 4 mm hex key (AJ)
and insert the rods into the holes provided. Now turn the screws again until the rods
engage with the screws of the back panel.
SS
S
S
S
S
S
S
S
S
AB AB
AB
AB
AB
AB
AB
AB
AB
AB

11 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 10
Insert the dowels (AM) in the four holes. Join the two identical connecting frame
halves (J). Place the three connectors (W) in the cut-outs and tighten them with the 4
mm hex key (AJ).
AM
AM
W
W
J
J

12 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 11
Join the connecting frame with the back element. It may be necessary to lift the cover
slightly for this step. Make sure that the cable (AG) is led through one of the two holes
of the connecting frame.
J
J
AG

13 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
click
click
click
Step 12
Place the blocks (V) on the floor and place the base plate (K) on top. Plug the cable
(AG) into the T-connector(AI). Insert also the plugs of the left (A) and right side (B)
into the distributor and make sure that the plugs snap in.
AG
AI
4
4
1
1
23
AB
K
V
VV
V

14 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 13
Place the base plate (K) on the four blocks (V) and make sure that they are aligned
as shown. Join the two sides (A and B) with the base plate (K). This should go easily,
otherwise the parts must be aligned better to each other.
K
VV
4
4
1
1
23
A B
2.
1.
2.

15 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
90º 90º
Step 14
Guide the cable of the side through the recess of the cover (M). Join the cover with
the two sides. This should go without too much resistance.
4
4
1
1
2
2
3
3
M

16 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 15
Move the two sides, the bottom and the cover into the back panel. It may be necessary
to lift the cover slightly.

17 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 16
Fahre die Stangen (S) in die vorgesehenen Aussparungen ein. Drehe die Stangen im
Uhrzeigersinn, bis sie mit dem Gewindestiften greifen, gegebenenfalls mit der Hilfe einer
Schraube (Y).
S
S
S
S
S
S
S
S
S
S

18 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 17
Insert the dowels (AE) in the four holes. Join the two halves of the frame (G and H). Place
the two connectors (W) in the cutouts and tighten them with the 4 mm hex key (AJ).
1.
1.
2.
2.
G
H
AE
AE
W
W

19 Chatpod 700 IMPACT ACOUSTIC AG, Bodenhof 4, 6014 Luzern, Switzerland
Step 18
Press the door threshold (T) over the frame and fix it with the four screws (AC). Tighten
the screws only handtight.
1.
2.
2.
2.
2. T
AC
AC
AC
G
H