impact PCSLEDK-110 User manual

PCSLEDK-110
Pro Copy Stand with
Dual LED Panel Light Kit
INSTRUCTIONS

2
Introduction
Thank you for choosing Impact.
The Impact Pro Copy Stand allows you to accurately and repeatedly shoot
products or documents. It provides an alignment grid, top-down shooting
platform, and dual LED lighting. The grid makes it easy to align each shot and
take the same image again and again. A shooting platform offers a top-down
angle over your subject and is mounted on an adjustable 42-inch sliding column.
Dual LED lighting means each object will be well lit, and the 5-way adjustment
allows lighting at any angle.
Precautions ⚠⚡
• Please read and follow the
instructions, and keep this manual
in a safe place.
• Keep this unit away from water
and any ammable gases or
liquids.
• Do not leave this unit in a closed
vehicle under the sun or in
other areas subject to very high
temperatures.
• Make sure this product is intact
and that there are no missing
parts.
• Do not attempt to disassemble or
repair the equipment. There are
high-voltage components inside
the unit. Failure to observe this
precaution could result in electric
shock or product malfunction. This
will void the warranty, and Impact
will not be responsible for any
damage.
• Use caution when expanding and
collapsing this product.
• Clean with only a soft, dry cloth.
• All images are for illustrative
purposes only.

3
Baseboard nish 18% matte gray
Grid Yes
Column height 42 in. (106.7 cm)
Camera mount 1/4-20
3/8-16 bushing
Weight capacity 8 lb. (3.6 kg)
Clamp width 1.45 in. (3.7 cm)
Light type LED
LED count 96 each
Max output 20 W
Color temp 5600 K
CRI 95
Beam angle 120°
Light intensity @ 1 ft. (30.5 cm): 5213 lx / 484.3 fc
@ 3 ft. (91.4 cm): 656 lx / 60.9 fc
Voltage 100–240 V AC
Avg lamp life 50,000 hr.
Max document size 16 × 20 in. (40.6 × 50.8 cm)
LED panel dimensions 7.8 × 5.4 in. (19.9 × 13.6 cm)
Baseboard dimensions 23.5 × 23.5 in. (59.7 × 59.7 cm)
Weight 23 lb. (10.4 kg)
Specications

4
Overview
1. Hex key holder
2. Slide column
3. Camera mounting screw with
1/4-20 thread and 3/8-16 bushing
4. Mounting screw cap
5. Platform extension
6. Camera mount
7. Camera platform
8. Quick-release handle
9. Horizontal support (×2)
10. Horizontal support adapter
11. Vertical adjustment locking knob
12. Vertical support (×2)
13. Clamp locking knob
14. Pivot locking knob
15. Table clamp (×2)
16. Baseboard
17. Alignment grid
18. Leveling feet
19. LED panel (×2)
20. Cold-shoe adapter
21. Tilt locking knob
22. Support locking knob
23. Cable tie
24. On/off switch
25. Power cable
26. Baseplate
27. 5 mm hex key
28. Hex screw (×4)
29. Hex screw washer (×4)
Additional Hardware
• 17 mm short extension screws
• 17 mm washers
• Spare backstop screw and spacer

5
1
2
21
22
4
12
15
17
16
18
5
3
26 27
19
11
24
25
7
8
6
28
13 14
9
23
29
10
20

6
Setup
Base and Slide Column Assembly
1. Remove the hex key from its storage holder on
top of the sliding column.
2. Use the hex screws and washers to attach the
baseplate, baseboard, and slide column. Make
sure the camera platform is positioned over
the baseboard. Use the hex key to tighten until
secure.
1
2

7
Table Clamp / Light Assembly
Follow these instructions for both support arms.
1. Unscrew and remove the clamp’s pivot locking
knob.
3. Loosen the clamp locking knob, and t the clamp
onto the baseboard, one support arm on each
side of the sliding column. Tighten until secure.
2. Align the vertical support with the clamp. Screw
the pivot locking knob through the washer and
into the clamp assembly. Tighten until secure.
1
2
3

8
4. Slide the horizontal support’s adapter over the
vertical support. Tighten the adapter’s locking
knob until secure.
5. Loosen the LED’s support adapter, and slide it
over the horizontal support. Tighten until secure.
6. Plug each of the LED panels into a power source, and press the power
switches to On.
4
5

9
Mounting a Camera
1. Unscrew the mounting screw cap to reveal the
3/8-16 bushing. Remove the bushing to reveal
the 1/4-20 threaded screw.
2. Align and mount your camera onto the 3/8-16 or
1/4-20 threaded screw. Tighten until secure.
3. Press the quick release handle to raise or lower
your camera. Release to lock in place.
1
2
3

10
Removing the Camera Platform Extension
The camera platform extension can be removed to accommodate a larger
camera setup.
1. Use the hex key to remove the three screws
from the front of the camera platform, and then
remove the platform extension.
2. Screw in the three provided 17 mm short
extension screws to secure the camera mount
to the platform.
1
2