impact quikbox User manual

1
Quikbox Micro Softbox
INSTRUCTIONS

2
Thank you for choosing the Impact Quikbox Micro On-Camera Softbox. This
convenient 9 × 9 in. light modifier slips onto an on-camera flash in seconds,
transforming the light produced by the flash from harsh to soft and diffused. The
reflective silver interior minimizes light loss, while the included front diffusion screen
and internal baffle make it possible to customize the degree of diffusion for the effect
you desire.
The Quikbox Micro On-Camera Softbox is ideal for portraits, weddings, events, or
any time you photograph people with your on-camera flash. It’s compatible with
most on-camera flashes, including the Nikon SB-910 and the Canon 600EX-RT.
Touch-fastener straps make it fast and easy to mount and dismount the softbox with
any flash.
Introduction
Precautions
• Please read and follow these instructions,
and keep this manual in a safe place.
• Keep this unit away from liquids and any
flammable gases.
• Handle the unit with care.
• Clean the unit with a soft, dry cloth.
• Keep this unit away from children.
• Use only parts provided by the
manufacturer.
• Make sure the item is intact and that there
are no missing parts.
• All photos are for illustrative purposes only.
Contents include:
• Impact EBO-0699
Quikbox Micro Softbox
• Front diffuser
• Internal baffle
• Carrying case
• User manual
• One-Year Limited
Warranty

3
Using the Quikbox Micro On-Camera Softbox
1. Remove the softbox, front
diffuser and internal baffle
from the carrying sleeve.
2. Pull the softbox open to form
a square shape.
3. Note that the largest of
the panels is the top of the
softbox.
4. Position the flash head so
that it will point straight
ahead when mounted on the
camera.

4
5. Before attaching your flash
to a camera, insert the front
of the flash head through the
elasticized opening in the rear
of the softbox. Leave the back
end of the flash head outside
the rear of the softbox.
6. Attach the inner set of touch-
fastener strips one on top of
the other across the pivoting
portion of the flash head until
they’re secure across the
back of the flash.
Using the Quikbox Micro On-Camera Softbox

5
7. Close the outer set of touch-
fastener strips tightly over the
inner set of touch-fastener
strips.
8. There are two pieces of
diffusion material included:
the small internal baffle and
the larger front diffuser.
9. To mount the internal baffle,
insert it into the front of the
softbox and attach the four
corners of the baffle to the
four touch-fastener tabs
inside the softbox. Adjust the
touch-fasteners so that the
baffle spreads evenly across
the softbox.

6
Using the Quikbox Micro On-Camera Softbox
10. To mount the front diffuser,
position it so that the touch-
fastener strip faces the
interior of the softbox, then
press the strip along one side
of the front of the softbox.
Continue by pressing another
side of the diffuser against a
side of the softbox, and follow
through until all four sides are
attached to the softbox.
11. Mount the flash normally on
the camera’s hot shoe.
Note: You may use the Quikbox
Micro Softbox with the internal
baffle alone, the front diffuser
alone, both the baffle and the
diffuser together, or without either
the baffle or the diffuser–depending
on the effect you desire. You may
also leave the diffuser, the baffle, or
both in place when collapsing the
softbox for storage.

7
Specifications:
·Dimensions (WxHxD): Overall: 11 × 10.75 × 9 in. (28 × 27 × 23 cm)
Front diffuser: 9 × 9 in. (23 × 23 cm)
·Weight: 10 oz. (283.49g)
One-Year Limited Warranty
This IMPACT product is warranted to the original purchaser to be free from defects in materials
and workmanship under normal consumer use for a period of one (1) year from the original
purchase date or thirty (30) days after replacement, whichever occurs later. The warranty
provider’s responsibility with respect to this limited warranty shall be limited solely to repair
or replacement, at the provider’s discretion, of any product that fails during normal use of this
product in its intended manner and in its intended environment. Inoperability of the product or
part(s) shall be determined by the warranty provider. If the product has been discontinued, the
warranty provider reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration,
abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specic legal rights,
and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Impact Customer Service Department to obtain a
return merchandise authorization (“RMA”) number, and return the defective product to Impact
along with the RMA number and proof of purchase. Shipment of the defective product is at the
purchaser’s own risk and expense.
For more information or to arrange service, visit www.impactstudiolighting.com or call
Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
IMPACT is a registered trademark of the Gradus Group.
© 2017 Gradus Group LLC. All Rights Reserved.
IMPACT
®
A Gradus Group Brand

8
GG4