IN-COMMAND NCTP100 User manual

©
2016 ASA Electronics LLC
.
MA6A192800A-Y
NCTP100
Tire Pressure Monitoring System
Installation and Operation Manual (English)

Contents
Important Safety Information...................................................................................................................................................... 2
INTRODUCTION ................................................................................................................................................................... 3
INSTALLATION...................................................................................................................................................................... 4
B LUETOOTH R EPEATER I NSTALLATION ....................................................................................................................................... 6
SPECIFICATIONS.................................................................................................................................................................. 7
NOTES..................................................................................................................................................................................... 8
MOBILE DEVICES................................................................................................................................................................. 9
Pairing a Mobile Device ................................................................................................................................................... 9
Create New Vehicle Profiles.............................................................................................................................................. 10
Sensor Pairing .................................................................................................................................................................. 11
Tire Deflation Sensor Pairing ........................................................................................................................................... 11
Manual Sensor Pairing ..................................................................................................................................................... 12
QR Code Sensor Pairing ................................................................................................................................................... 13
Alert & Units & Ranges Settings ....................................................................................................................................... 14
Tire Locations Settings...................................................................................................................................................... 15
Information ....................................................................................................................................................................... 16
System Warnings............................................................................................................................................................... 16
RETAIL 12 MONTH LIMITED WARRANTY .................................................................................................................... 17
TROUBLESHOOTING......................................................................................................................................................... 17

Important Safety Information
Read these warning and instructions carefully before using this product*. Failure to follow these instructions in this
owner’s manual, or improper use of the Mobile Application, could result in personal injury, including death.
Complete Tire Pressure Monitoring System (TPMS) App set-up before driving. The driver does not need to constantly
view the TPMS App. Warning notifications will be issued when abnormal conditions are found in the tires.
TPMS sensors only transmits data when the sensor is on a vehicle that is going over 20 miles per hour.
The smart device with app installed needsto have Bluetooth turned on and the TPMS App needsto be running the
background in order to receive on-screen and audible warning notifications when device volume is turned on.
The smart device should be in a viewing area that does not affect normal driving.
It is recommended to check for any air leakage from the tires after the TPMS sensors have been installed.
This iN-Command TPMS does not have a warning notification for side wall failure. However, the warning notifications
for irregular tire pressure and temperature may help prevent a failure.
It is still necessary to perform regular maintenance and visual inspections of yourtires.
This mobile application is intended for adult use only.
*Information in this manual is subject to change without notice.

• INTRODUCTION
Thank you for choosing iN-Command TPMS. We hope you will find the instructions in this owner’s manual clear and
easy to follow. If you take a few minutes to lookthrough it, you’ll learn howto use all the features of your new
NCTP100 for the best safety results.
With this new product: Bluetooth Low Energy Tire Pressure Monitoring System (hereinafter referred to as BLE
TPMS), you can get accurate tire pressure and temperature at anytime through your smart phone via the
iN-Command TPMS App. When the system detects abnormal status, it will alert you, and showthe abnormal data
and tire location on the Bluetooth TPMS App (hereinafter referred to as App).
• Packaging Contents
1. Lock Nut* (4)
2. Anti-Theft Attachment (4)
3. Tire Sensor (4)
4. Battery (4) CR1632
5. Wrench** (1)
6. Bluetooth Repeater (1)
*The Lock Nuts are used with the Anti-Theft Attachment to prevent the sensor from being removed from the tire stem.
**The wrench is used to tighten or loosen the lock nuts and can be used to remove the cover from the sensor. It is
recommended to keep the wrench in the vehicle in case you need to remove the sensor or replace the battery.

•
INSTALLATION
Use the included wrench to remove the cover from the TPMS sensor. Install the battery with
the positive terminal facing upward then reinstall cover. Attach anti-theft attachment to
bottom of sensor.
Screw Locking nut onto tire valve. *
*This product is recommended with a metal valve, or to replace the original
valve regularly to ensure better quality.
Tire valve
6
• INSTALLATION
Use the included wrench to remove the cover from the TPMS sensor. Install the battery with
the positive terminal facing upward then reinstall cover. Attach anti-theft attachment to
bottom of sensor.
Screw Locking nut onto tire valve. *
*This product is recommended with a metal valve, or to replace the original
valve regularly to ensure better quality.

Screw TPMS sensor onto tire valve, using included wrench totighten onto locking nut.
After installation, please download the App and proceed with all settings.

• Bluetooth Repeater Installation
The Bluetooth Repeater is weather-resistant and can be mounted outside.
We recommend connecting the repeater to a switched power source, like the running lights. This will allow you toturn
the repeater on/off with the running lights. If the repeater is connected to constant battery power, the repeater will stay
on at all times and will draw on the battery.
It is recommended to install the repeater for large travel and 5th wheeltrailers. It is optional for motorhomes.
When installing the repeater, have the side labeled “Front” pointed towards the vehicle. The “Front” side transmits the
signaltowards the app and “Rear” side receives the signal from the sensors.

• SPECIFICATIONS
BLE TPMS SENSOR
Operating Voltage 3V
Operating Humidity 95 % MAX
Operating Current ＜15 mA at DC 3V
Storage Temperature -40˚F to 185 ˚F
Operating Temperature -4 ˚F to 185 ˚F
Monitored Pressure Range 0 to 184 psi
Monitored Temperature Range -4 ˚F to 185 ˚F
Operating Frequency 2.4GHz
Transmission Power 4 dBm MAX
Battery Life 1 year (under normal operating condition)
Battery Capacity 130 mAh (CR1632)
Weight 10 g ± 0.5 g (including battery)
REPEATER SENSOR
Operating Voltage 12V/24V
Operating Humidity 90 % MAX
Storage Temperature -40 ˚F to 257 ˚F
Operating Temperature -4 ˚F to 185 ˚F
Operating Frequency Bluetooth Low Energy 4.0, 2400MHz~2483.5MHz
Transmission Power 4 dBm MAX
Receiver Sensitivity < -85dBm
Modulation format GFSK
Operating Current 40mA Max. @ DC 12V

• NOTES
Consult your vehicle manual or a tire professionalto determine the propertire pressure for your vehicle. It is
recommended to set the tire pressure when the ambient temperature is cool or low and before the vehicle has been
driven.
Dramatic changes in tire pressure can occur from the following: change in ambient temperature, wheel and axle loads,
and exposure tothe sun. These and other conditions should be taken into consideration when setting initial tire
operating pressures.
If the TPMS sensor is low on battery, or other abnormal conditions exist, the TPMS sensors will continuously emit
signals to warn the driver as long as those conditions are present. This will cause the battery to have a shorter life
span. Contact atire specialist or service station to confirm whetherthe battery needs to be replaced, TPMS sensor
needsto be replaced, or if there is an issue with the tire.
Make sure the tire stem and Schrader Valve (core inside the valve stem) are in good condition. The Schrader Valve
should be the correct size and able to be depressed fully to allow the release of air tothe sensor for proper operation.
Also, keep these same considerations in mind when using valve stem extensions. Metal bodied stems or T-Valve
type are recommended for best performance. We recommend contacting a tire professionalto ensure that the tire
stem and Schrader Valve are installed and operating correctly.
Temporary resealing or re-inflation with product injected through the valve hole may adversely affect the operation of
the sensor. Furthermore, do not place the TPMS sensor in contact with tire sealant, balancing compounds or any
other chemicals. This can cause damage to the sensor and prevent it from functioning properly.
This system operates on a Bluetooth Low Energy system. As with any wireless systems, this system can occasionally
suffer from interference depending on the distance between the sensors and your smart device, thus causing the
system to be inaccurate or not operate at all.
Do not solely rely on the iN-Command TPMS for safety! Continue to check the condition and pressure of your
vehicles tires on a regular basis as described by the manufacturer of the vehicle or tire manufacturer. Tire pressures
and temperatures are not the only thingsthat can affect tire safety; we suggest daily visual inspections and periodic
checks by tire professionals.

• MOBILE DEVICES
iN-Command TPMS is able to pair to Android and iOS devices using the iN-Command TPMS App.
Visit the Google Play and Apple App stores on your mobile device to download and use the iN-Command TPMS App.
(Note: The images shown may not match your specific device.)
• Pairing a Mobile Device
1. Enable "Bluetooth" in the system settings of the mobile device.
2. When opening the app for the first time, 2 prompts will appear. If either of these prompts are denied, some of
the app features will not function.
3. After the initial prompts, a Notice will appear.

• Create New Vehicle Profiles
1.Press the “+” button in the
settings menu page.
2.Select vehicle configuration and
type.
3. Select the tire configuration.
4. Vehicle list
5.Press “ ” to enter Edit
6.From Edit, you can “Delete” a
vehicle or edit the “Name” of a
vehicle.

• Sensor Pairing
• Tire Deflation Sensor Pairing
1. Press “ ”, then select
“Sensor Pairing” -
>Deflation.
2. Select tire location #.
3.
Install sensor on the valve stem
of the associated tire, being
careful not to over tighten.
4. App will search for deflation
signal and display sensor’s ID
number.
Repeat step 1-3 for any
remaining tires with sensors.
Note: Sensor will transmit
learning signal for 10 minutes
after sensor’s battery is installed.
If additionaltime is required,
remove and reinstall battery to
restart learning signal.

• Manual Sensor Pairing
1. Press “ ”, then select
“Sensor Pairing” ->
Manual.
2. Select tire location #. 3. Enter selected tire’s sensor ID
number.
Repeat steps 1-2 for any
remaining tires with sensors.
Note: Sensor will transmit
learning signal for 10 minutes
after sensor’s battery is installed.
If additionaltime is required,
remove and reinstall battery to
restart learning signal.

• QR Code Sensor Pairing
1. Press “ ”, then select
“Sensor Pairing” -> QR Code.
2. Select tire location #.
3. Device camera will launch.
3. Position sensor’s QR Code within
camera’s guid
elines until QR Code is
automatically captured.
Repeat step 1-3 for any
remaining tires with sensors.

•
Tire Locations Settings
1. Select tire loc
ation # and drag to desired location #
to exchange the two tires/sensors.
2. Accept the exchanged locations and the tire’s
associated location #s will update automatically.

• Information
The Information page describesthe definition of
“iN-Command TPMS” and provides contact
information for ASA Electronics. You can press the
link to go tothe company’s website.
System Warnings：
Defines the pressure, temperature and alarm
warning. When abnormal tire system status occurs,
the value of the corresponding tire turns red, and it
alarms with a sound and warning symbol.
The warning symbols on each tire display, from t
op to
bottom, are: tire pressure warning, tire temperature
warning, low battery power of sensor and no signal.
1. Warning of high tire pressure or low tire
pressure
Tire pressure is higherthan maximum tire
pressure value or lower than minimum tire
pressure value on the APP.
2. Warning of high tire temperature
Tire temperature is higherthan maximum
temperature value on the APP.
3. Low battery power warning of TPMS sensor
Battery power of TPMS sensor is low.
4. Normal signal
No signal
Red symbolizes that the app has not received
any signal from the tire sensor.
• System Warnings

•RETAIL 12 MONTH LIMITED WARRANTY
ASA Electronics (ASA) warrants tothe original retail purchaser of this iN-Command product that should this
product or any part thereof, under normal use and conditions, be proven defective in material or workmanship
within 12 months from the date of original purchase, such defect(s) will be repaired or replaced (at ASA’s option)
without charge for parts and repair labor.
This warranty does not extend tothe effects of this device on other devices, to costs incurred for removal or
reinstallation of the product, or to damage of any product, accessories, or electrical system(s). This warranty does
not apply to any product or part thereof which, in the opinion of the company, has been damaged through alteration,
improper installation, mishandling, misuse, neglect, or accident.
THE EXTENT OF ASA’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT PROVIDED ABOVE, AND, IN NO EVENT, SHALL ASA’S LIABILITY EXCEED THE PURCHASE
PRICE PAID BY THE PURCHASER FOR THE PRODUCT.
Disclaimer:
This product is only to be used as a precautionary warning and to provide user as convenient secondary safety
equipment. Please follow the standard installation procedures or ask a qualified tire shop to install the product. If
the tire has been damaged or a traffic accident resulting from improper driving behavior occurs, the company will
not be responsible for any civil or criminal liabilities.
• TROUBLESHOOTING
After inputting the sensor ID number into the APP, the dialogue display remains without a value.
TPMS sensor only transmits data when the sensor is on a vehicle that is going over 20 miles per hour, the
tire pressure changes 5 PSI, or when the battery is installed.
During other times, data will not be transmitted in orderto save power. You can check if the TPMS sensor
is working normallythrough tire pressure increase or deflation.
Smart phone has completed the installation of the APP, the sensor ID settings are done, and the car is being driven,
but no data is shown.
Check if Bluetooth was turned off and restart the app.
If you experience an intermittent signal, close all other apps. (Wireless audio streaming via Bluetooth may
cause interruptions in signal.)

• Alert & Units & Ranges Settings
1.Select Alarm Tone. 2.Select units & Ranges
℃、℉temperature unit and pressure upper and
lower limits.
Pressure Range: 0-217 psi; Default 100-150 psi
Temperature Range: 100℉-257(38℃-125℃);
Default: 211℉(100℃)

There is no alarm sound warning for abnormality of tires.
Check if the device is in silent mode or if the volume has been turned to lowest setting.
Certain models of iPhone will not give audio alerts if connected to multiple Bluetooth devices
simultaneously.
For additionaltroubleshooting, call ASA Electronics Technical Support at 1-800-688-3135, email
[e-mail] or visit our website https://in-command.net/tpms/