Curt Manufacturing 12113 User manual

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
MAKE: STYLE:
20
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
MODERATE
EASY MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product
.
YEARS: 2014-2015 KIA MODEL: SORENTO SUV
3500
350
TRAILER WEIGHT:
TONGUE WEIGHT:
12113 INSTALLATION INSTRUCTIONS
LBS.
LBS.
7/25/2018
WARNING:
WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER
(WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT
WWW.CURTMFG.COM FOR FURTHER INFORMATION.
40 MIN.
MIN.
PRO INSTALL TIME:
NOVICE INSTALL TIME:
IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
YEARS: 2013-2018 MAKE:
HYUNDAI MODEL: SANTA FE (2.0 / 2.4L 4 CYL ONLY)
- NO DRILLING REQUIRED
- LOWER SPARE & UNDER
BODY PANELS
RATCHET
TORQUE
WRENCH SOCKET
EXTENSION
6"
SOCKET
7/16"
3/4"
17mm
SCREW
DRIVER
SAFETY
GLASSES
- CLEAN EXISTING
WELDNUTS
- LOWER EXHAUST

INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
CARRIAGE BOLT1/2-13 x 4 1/241
HEX FLANGE NUTHFN 1213, GR842
HEX BOLTM10 - 1.25 x 25
4
3
CONICAL TOOTHED WASHER3/8"
44
.188" SPACER PLATE12113-SP
15
5
1
2
3
4
1. Lower and remove spare tire.
2. Lower exhaust by removing (3) rubber isolators.
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
DESIGNED FOR USE WITH
BALLMOUNT #45520/D-20
DESIGNED FOR USE WITH EURO BALLMOUNT
#45561 (1 7/8" BALL) OR #45562 (2" BALL)

INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Remove the plastic under body panel from the passenger
side and the driver side frame rails. Remove (3) fascia
screws from the passenger side and (4) from the driver
side. Carefully pull down and set aside.
4. Raise hitch into position and secure to the existing
weldnuts with M10-1.25 x 25mm bolts and 3/8"
conical toothed washers. Note:The bumper locator
pin may interfere with the hitch hardware. You may
need to bend or trim it to allow hardware clearance.
5. Insert 1/2-13 x 4 1/2" carriage bolts through the driver side
plate and frame rail, secure using 1/2-13 flange nuts. Insert
1/2-13 x 4 1/2" carriage bolts through the 12113-SP spacer,
in the passenger side frame rail and out the passenger side
plate, secure using 1/2-13 flange nuts.
6. Torque all 1/2" hardware to 110 ft-lbs.
Torque all 10mm hardware to 48 ft-lbs.
Raise exhaust and spare tire back into position.
Reinstall passenger side and driver side under
body panels removed in Step (3).
BUMPER LOCATOR PIN

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
3500 350
KIA SORENTO & HYUNDAI SANTA FE
7/20/2017
12113
40
27
20
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
39615
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
CARRIAGE BOLT1/2-13 x 4 1/241
HEX FLANGE NUTHFN 1213, GR842
HEX BOLTM10 - 1.25 x 2543
CONICAL TOOTHED WASHER3/8"
44
.188" SPACER PLATE12113-SP
15
1
3
4
2
5
1. Lower and remove spare tire.
2. Lower exhaust by removing (3) rubber isolators.
3. Remove the plastic under body panel from the passenger side and the driver side frame rails.
Remove (3) fascia screws from the passenger side and (4) from the driver side.
Carefully pull down and set aside.
4. Raise hitch into position and secure to the existing weldnuts with M10-1.25 x 25mm bolts and
3/8" conical toothed washers.
5. Insert 1/2-13 x 4 1/2" carriage bolts through the driver side plate and frame rail, secure using 1/2-13 flange nuts.
Insert 1/2-13 x 4 1/2" carriage bolts through the 12113-SP spacer, in the passenger side frame rail and out the
passenger side plate, secure using 1/2-13 flange nuts. Note:The bumper locator pin may interfere with the hitch
hardware. You may need to bend or trim it to allow hardware clearance.
6. Torque all 1/2" hardware to 110 ft-lbs.
Torque all 10mm hardware to 48 ft-lbs.
7. Raise exhaust and spare tire back into position. Reinstall passenger side and driver side under body panels
removed in Step (3).
EXISTING WELD NUT
(BOTH SIDES)
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
BUMPER LOCATOR PIN
(BOTH SIDES)
- NO DRILL
- LOWER SPARE
- LOWER EXHAUST
- LOWER UNDER BODY PANELS
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
6" SOCKET EXTENSION
7/16" SOCKET
3/4" SOCKET
17mm SOCKET
SCREW DRIVER
SAFETY GLASSES
DESIGNED FOR USE WITH
BALLMOUNT #45520/D-20
DESIGNED FOR USE WITH
EURO BALLMOUNT
#45561 (1 7/8" BALL) OR
#45562 (2" BALL)