In Light Facemask 104 User manual

INLIGHTTHERAPYINC.COM
Inlight Therapy Pads
Selection & Placement
1.
2.
3.
4.
5.
6.
7.
1. Facemask 104*
Face
2. Painbuster 90
Small Joints,
and Hands
3. Local 132
Acute Pain Sites,
and Hands
4. T-Pad 263
Shoulders, Knees,
Back, and Groin
5. Painbuster 180
Larger Joints,
Limbs, and Neck
6. Body 264
Torso, Lower Back,
and Thighs
7. Boot 122
Lower Calfs,
and Feet
ANATOMY GUIDE
Blue/NIR
BLUE |470 nm
NIR |850 nm
Tricolor
RED |630 nm
BLUE |470 nm
NIR |850 nm
Red/NIR
RED |630 nm
NIR |850 nm
Inlight Therapy systems offer a variety of pad shapes
for different anatomical uses. This guide will help you
to quickly select the appropriate pad to fit the most
frequently targeted anatomical use cases.
Inlight Therapy pads are available in Red, Blue, and
Tricolor configurations.
*The Inlight Therapy Facemask 104 only uses Red, and Blue LEDs.
It does not utilize Near Infrared (NIR) LEDs.
Representative's Business Name
Representative Name
Phone • Email

QUICK START GUIDE
©2021 Inlight Therapy, Inc. 1SH-AG&QSGInlight Therapy, Inc. 2703 Broadbent Parkway NE, Suite H, Albquerque, NM 87107
INLIGHTTHERAPYINC.COM
Inlight Therapy, Inc. products are legally marketed as a Class II Medical Device under FDA indications for use to temporarily relieve minor pain, stiffness, and muscle
spasms; and to temporarily increase local blood circulation. The light emitted from Inlight Therapy devices is within the visible to infrared spectrum and consists of
non-ironizing radiation, which is safe for use. Clients choose Inlight Therapy PLT for its convenience, value, drug-free, and non-invasive healing properties.
DISCLAIMER: This system is not intended to diagnose, treat, cure, mitigate or prevent disease. If you have a disease or medical condition, consult with your physician
or health practitioners before using Inlight Therapy, Inc. products. Use only as directed.
Quick Start
3 Steps To Your First Session
1. Plug-In
Affix the Power Supply male plug to the female
receiver on the Controller.
Connect the Power Cord to AC (wall) power.
Plug the Pad Cord(s) into the Controller by aligning
the 5-pin connectors and sliding plugs into place.
2. Place Pad(s) Over Pain or Desired Site(s)
Place a Pad over the desired site –
LED side towards the body.
Light arrays should be in gentle contact with a
clean skin surface or a transparent barrier placed
on the skin.
Secure with minimum pressure to site with provided hook and loop fastener
straps or elastic bandage wrap to ensure continued proximity to the skin.
3. Turn On The Controller
To begin your session:
•2/Port Controller: Press the ON button.
•6/Port Controller: Press the ON/OFF button,
then press the START/STOP button.
All Controllers are preset to provide 20 minutes of light therapy per
session and automatically shut off at the end of the session.
On a 6/Port Controller, use the START/STOP button to pause
the timer if repositioning the Pad during the session.
See Owners Instruction Manualfor advanced functions
using the additional buttons.
Repeat
•Repeat treatment cycles on additional areas of pain as needed.
•Repeat up to 3 sessions per day per treatment site.
Indications for Use
To temporarily relieve minor pain,
stiffness, and muscle spasms;
and temporarily increase the
local blood circulation.
Helpful Hints
•
LEDs that do not appear to
illuminate when the Controller
is ON are the Near-Infrared (NIR)
LEDs. They produce light that is
not visible to the human eye.
The NIR LEDs are organized
in complete rows.
•
Avoid the use of any topical creams
or gels on skin before or during use.
•
It is normal to experience a
therapeutic warmth during use.
The Owners
Instruction Manual
Please refer to the Owners Instruction
Manual for complete operating
instructions.
Representative's Business Name
Representative Name
Phone • Email