In the Garage Ultimate Car Shield User manual

In the Garage AG – Zumikerstrasse 24, Zollikon 8702 Switzerland
1 / 5
Ultimate Car Shield/Bike Shield
What’s in the Box
Big Box: Ultimate Car/Bike Shield
Small Box: Accessories (see picture below)
• Air Pump, Air Hose, Deflation Nozzle, Maintenance Nozzle
• Pressure Tube & Pressure Adaptor
• Fans, Panel, AC Adaptor & Plug
• Air Filters & spare material
For further information on care and warranty:
www.inthegarage.com/instructions

In the Garage AG – Zumikerstrasse 24, Zollikon 8702 Switzerland
2 / 5
Instructions
Note: It should take about 20 minutes to set up the Ultimate Car Shield/Ultimate Bike Shield once
unpacked. We recommend two people.
This product is for indoor use only!
1. Unfold the Ultimate Car/Bike Shield and place it where it will be located when inflated
2. Connect one end of the Air Hose to the Inflate Side of the Air Pump
3. Insert the Maintenance Nozzle to the other end of the Air Hose
4. Place the Maintenance Nozzle in the lower (2) Maintenance Valve on the Ultimate Car/Bike Shield.
Note: There are no threads – just push it tightly. Ensure all is snugly closed
5. Connect the black Pressure Tube from the Pressure Adaptor to the port marked “Pressure Tube” on
the Air Pump

In the Garage AG – Zumikerstrasse 24, Zollikon 8702 Switzerland
3 / 5
6. Insert the Pressure Adaptor into the upper (1) Inflate/Deflate Valve on the Ultimate Car/Bike
Shield. Turn clockwise until it “clicks” into place. Ensure all is snugly closed.
7. Connect the electric cable to the Air Pump and plug it into an appropriate electrical outlet
8. Turn on the Air Pump using the red 0/1 switch.It will run for less than 5 minutes or until the optimal
pressure is reached and will maintain that pressure without intervention
Notes:
• This system allows constant maintenance without any user intervention in the event of pressure
drops common to all inflatable products
• You may need to assist the device by lifting the pillars during inflation to ensure a smooth rise. If it
is not fully inflated at five minutes, turn off the pump and unfold any portions which may be blocked
or stuck together
• You can choose to locate the Air Pump inside or outside the Ultimate Car/Bike Shield as there are
two sets of identical valves
WARNING! Do not overinflate or interfere with the pressure settings. Maximum inflation is
2.56PSI/0.17 Bar for Ultimate Car Shield and 1.91PSI/0.13 Bar for Ultimate Bike Shield

In the Garage AG – Zumikerstrasse 24, Zollikon 8702 Switzerland
4 / 5
9. Install the Fan by placing the Velcro panel on the inside of the Ultimate Car/Bike Shield. Press hard
10. With the AC Adaptor outside the device, run the power wire through the purpose-made slit and
connect to Fan. (do not plug in an electrical socket yet as you first need to install the Filter)
11. From the outside of the Ultimate Car/Bike Shield, place the Filter in the round opening by gently
bending the edges to make it fit. There is a specially-made slit in between the inside and outside panels
Tip: It is easier if you rotate the filter while installing

In the Garage AG – Zumikerstrasse 24, Zollikon 8702 Switzerland
5 / 5
12. Snap on the corresponding plug adaptor for your region onto the AC Adaptor
13. Plug the AC Adaptor in an appropriate electrical power socket
14. Close all zippers to allow the air to circulate properly
Note: when new, you may experience some “sticky” zippers. Do not force them. We recommend using
two hands to open/close zippers (one inside and one outside). Also, it is easier to close zippers when
the Fans are not running.
Deflation
1. Unscrew the cover inserted in the side marked "Deflate" from the pump
2. Connect one end of the Air Hose to the Deflate Side of the Air Pump. Remove the Maintenance
Nozzle and replace it with the Deflation Nozzle.
3. Disconnect the Pressure Adaptor from the upper valve marked “(1) Inflate/Deflate” on the Ultimate
Car/Bike Shield
4. Insert the Deflation Nozzle in the upper valve marked “(1) Inflate/Deflate”
5. Turn on the Air Pump using the red 0/1 button and the Ultimate Car / Bike Shield will deflate in less
than five minutes. You can eventually help by pressing the inner tab of the upper valve "(1) Inflate /
Deflate"
N.B.:
•
You may need to assist the device by lifting the pillars during deflation
• If it is not fully defalted at five minutes, turn off the pump and unfold any portions which may be
“stuck”