Infineon Lite SBC Series User manual

Z8F63697694
Automotive Power
Getting Started
Rev 1.0, December 2018
TLE9461-3ES / TLE9471-3ES
Evaluation Board
Lite SBC Family
Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 2 Rev 1.0, Dec 2018
Revision History: 1
Previous Version: none
Page
Subjects (major changes since last revision)
1.0
Initial Release, All.
Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 3 Rev 1.0, Dec 2018
Table of Contents
1. Evaluation Board Overview...............................................................................................................4
2. Banana Jacks .....................................................................................................................................4
3. Buttons................................................................................................................................................4
4. LEDs ....................................................................................................................................................4
5. Connectors .........................................................................................................................................5
5.1. uIO Connector......................................................................................................................................5
6. Jumper Configurations......................................................................................................................6
6.1. Power Supply Configuration.................................................................................................................6
6.2. General Configuration: INTN and TEST pins.......................................................................................7
6.3. Jumpers to connect/disconnect the Vccx LEDs...................................................................................8
6.4. Configuration related to the WK/VSENSE and FO/GPIO pins ............................................................9
6.5. CAN termination.................................................................................................................................12
7Charge Pump......................................................................................... Error! Bookmark not defined.
8Layout and Materials Details...........................................................................................................14
9Appendix...........................................................................................................................................17
9.1 Schematics Evaluation Board (TLE9461)..........................................................................................17
9.2 Schematics Evaluation Board (TLE9471)........................................... Error! Bookmark not defined.
9.3 Layout Evaluation Board (with Overlay).............................................................................................17
9.4 Layout Evaluation Board (Top layer)..................................................................................................18
9.5 Layout Evaluation Board (Bottom layer) ............................................................................................18
10 Additional Information .......................................................................................................................19
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 4 Rev 1.0, Dec 2018
1. Evaluation Board Overview
There are 2 banana jacks, 4 LEDs, one wake up button, one connector for the uIO and a set of headers for
jumper configurations on the evaluation board. The functionality behind these components is explained in the
following chapters. The distribution of these elements on the board can be observed in the figure below:
Figure 1: Board overview
2. Banana Jacks
The SBC is usually supplied through the VBAT (X6, typ 13.5 V) and GND (X9) banana jacks (alternatively see
Chapter 6.1 to supply it with the uIO stick).
The VCC1 (X11, 5 V or 3.3 V, depending on the SBC’s version) and VCC2 (X11, 5 V) screw terminals provide
the regulated output voltages of the SBC. The voltages VCC1 and VCC2 are simultaneously used to support
signal LEDs at the output clamps.
The charge pump stage of the SBC drives two MOSFETS at the evalboard. One to protect SW against reverse
polarity, the other is used as a VBAT power switch, supporting the SW (X7) terminal.
3. Buttons
The wake up button (WK) wakes up the SBC (from Sleep and/or Fail Safe Mode), if the corresponding jumpers
are properly configured (see Chapter 6.4 for more information).
4. LED’s
The LED FO (D8) and LED GPIO (D7) indicate the voltage level of the FO/GPIO pins, if the corresponding jumpers
are properly configured (see Chapter 6.4 for more information).
The VCC1 LED (D1) lights, if VCC1 is enabled and the VCC2 LED (D5), if VCC2 is enabled, if the corresponding
jumpers are connected (see Chapter 6.3 for more information). Only one LED (LED FO or LED GPIO) can be
used at a time.
GND
VBAT
LED VCC2
Wake
Up
LED VCC1
LED GPIO
LED FO
uIO
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 5 Rev 1.0, Dec 2018
5. Connectors
5.1. µIO Connector
The µIO Connector corresponds to the X14 on the board. The pin distribution of the connector is shown in the
following figure:
Figure 2: X14 µIO connector
The functionality of the X14’s pins is detailed in the following table:
Pin
Functionality
Pin
Functionality
1
NC
2
GND
3
NC
4
NC
5
NC
6
VS_UIO
7
NC
8
INTN
9
CSN
10
NC
11
CLK
12
FO_UC
13
SDO
14
RSTN
15
SDI
16
ADC_UIO
Table 1: Pins of the µIO connector
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 6 Rev 1.0, Dec 2018
6. Jumper Configurations
6.1. Power Supply Configuration
The SBC can be supplied with VBAT (typical use case) or through the 12V provided by the uIO (if plugged in
and connected to a USB port). This can be configured with the jumper X10, located close to the reset button:
Figure 3: Jumper to configure the SBC´s power supply
The possible configurations are as follows:
X10
SBC supplied through Vbat (12 V)
Connect VBAT
SBC supplied through uIO (12 V)
Connect VSUP and VS_UIO
Table 2: X10 Cofiguration
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 7 Rev 1.0, Dec 2018
6.2. General Configuration: INTN and TEST pins
These jumpers are located at the left side of the board:
Figure 4: Jumpers for SBC configuration purposes
The jumper X24 allows to select the hardware configuration of the SBC (configuration 1/3 or 2/4):
X24
Config 1/3
Connect INTN and Vcc1
Config 2/4
Leave open
Table 3: X24 Cofiguration
Through the jumper X27 the operation mode of the SBC can be selected:
X27
Development Mode
Connect Vcc1 and TEST (no need to start watchdog)
User Mode
Leave open
Table 4: X27 Cofiguration
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 8 Rev 1.0, Dec 2018
6.3. Jumpers to connect/disconnect the VCCx LEDs
These jumpers are located at the left bottom of the board:
Figure 5: Jumpers for the Vccx LEDs
If X13 is connected and VCC2 is enabled, the VCC2 LED (D5) shines. In the same manner, if X8 is connected
and VCC1 is enabled, the VCC1 LED (D1) shines.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 9 Rev 1.0, Dec 2018
6.4. Configuration of the WK/VSENSE and FO/GPIO pins
These jumpers are located at the top right corner of the board:
Figure 6: Jumpers related to the WK/VSENSE and FO/GPIO pins
The possible configurations are shown in the following table. Note, that these are the only possible configurations
due to the fact that functionalities are multiplexed:
X26:
FAIL OUTPUT
X16:
WAKE SOURCE
X17:
WAKE / VSENSE
SELECT
X19:
FO/GPIO LED
VsSense
Connect Pin 2+3
Open
Connect Pin 2+3
Open
Cyclic Sense
Open
Connect Pin 2+3
Connect Pin 1+2
Open
Regular wake up
(wake up through
wake up button)
Open
Connect Pin 1+2
Connect Pin 1+2
Open
GPIO as HS (LED
D7 as load)
Open
Open
Open
Closed
FO (LED D8)
Connect Pin 1+2
Open
Open
Open
Regular wake up
and FO
Connect Pin 1+2
Connect Pin 1+2
Connect Pin 1+2
Open
Regular wake up
and GPIO as HS
Open
Connect Pin 1+2
Connect Pin 1+2
Closed
Table 5: Configurations related to the WK/VSENSE and FO/GPIO pins
1
2
3
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 10 Rev 1.0, Dec 2018
VsSense:
Cyclic Sense:
Regular wake-up:
GPIO as HS (LED D7 as load):
x
For the voltage sensing, check the “Voltage Sensing” button in the
config wizard.
For the cyclic sensing, choose “High-Side Timer” from the drop-down
menu at GPIO.
For the regular wake-up, press the “Soft Reset” button in the Mode
section.
For GPIO as HS switch, choose High-Side PWM in the GPIO field and
chose the PWM Duty Cycle.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 11 Rev 1.0, Dec 2018
FO (LED D8):
For the failure output, choose “Failure Output” from the drop-down
menu at GPIO.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 12 Rev 1.0, Dec 2018
6.5. CAN connector
The connector for CANH and CANL is X23. The CAN terminations are fixed.
Figure 7: Jumper for the CAN terminations
For proper termination of the CAN bus, two 62Ωresistors are connected in series, differentially between CANH
and CANL. In addition, there is a 4.7nF capacitor supporting bus-symmetry during data-transmission.
Figure 8: CAN termination
In case, a Common Mode Choke (CMC) is considered to further improve electromagnetic compatibility /
immunity, a landing pattern is designated, either using R19 and R26 or replacing it with the CMC.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 13 Rev 1.0, Dec 2018
7 Charge Pump
The internal charge pump provides a gate control voltage for VBAT connected NMOS transistors. This allows
the smart control of a reverse polarity protection circuit and or a VBATpower switch.
As a switched power connection example, a DC Motor can be connected to the TLE9461 / TLE9471 board
through the SW and GND (X7) pins as shown in Figure 10:
Figure 10: DC Motor connection to the board
In order to start the motor, press the “Soft Reset” button and check the “Charge Pump” box in the Config
Wizard.
Note: For more information, plese check chapter 14 in the datasheet.
Motor
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 14 Rev 1.0, Dec 2018
8 Layout and Materials Details
In the following table, all the devices used on the board (BOM) are described in detail:
Item
Value
Package Reference
Manufacturer
Part Number
C1
2.2u (TLE9461)
1210
Kemet
C1210C225K4RAC
C1
22u (TLE9471)
1210
Kemet
C1210C226K4RAC
C2
100n
0603
AVX
06035C104K4Z2A
C3
220p
0603
Kemet
C0603C221F1GAC
C4
100n
0603
AVX
06035C104K4Z2A
C5
100n
0603
AVX
06035C104K4Z2A
C6
4.7u
1210
Kemet
C1210C475M5RAC
C7
68u
F
Panasonic
EEHZA1H680P
C8
10n
0805
AVX
0805YC103K4Z2A
C9
2.2u
0805
Kemet
C0805C225K4RAC
C10
100n
0603
AVX
06035C104K4Z2A
C11
1u
0603
muRata
GRM188R71E105KA12D
C12
10n
0603
Kemet
C0603C103K5GAC
C13
100n
0603
AVX
06035C104K4Z2A
C14
100n
0603
AVX
06035C104K4Z2A
C15
1u
1206
Kemet
C1206C105K5RAC
C16
4.7n
0603
Kemet
C0603C472F8GAC
D1
0603
OSRAM Opto
Semiconductors
LG Q971-KN-1
D2
SOD-123
Micro Commercial
Components
MBR0560-TP
D3
DO-214AC
ON Semiconductor
SZ1SMA5927BT3
D4
SOD-323
ON Semiconductor
BAS21HT1G
D5
0603
OSRAM Opto
Semiconductors
LG Q971-KN-1
D6
SOD-323
ON Semiconductor
BAS21HT1G
D7
0603
OSRAM Opto
Semiconductors
LS L29K-H1J2-1
D8
0603
OSRAM Opto
Semiconductors
LS L29K-H1J2-1
D9
SOD-323
Vishay General
Semiconductor
GDZ5V1B-G3-08
L1
10µH
4532 (1812)
muRata
LQH43PB100M26#
L2
2.2uH
SMD
Murata
1227AS-H-2R2M=P2
Q1
IPD90N06S4L-03
PG-TO252-3-11
Infineon Technologies
IPD90N06S4L-03
Q2
IPD90N06S4L-03
PG-TO252-3-11
Infineon Technologies
IPD90N06S4L-03
Q3
BCR183
SOT23
Infineon Technologies
BCR183E6327HTSA1
Q4
BCR183
SOT23
Infineon Technologies
BCR183E6327HTSA1
R1
0R
2512
Yageo/Phycomp
R2
0R
0603
Yageo/Phycomp
RC0603JR-070RL
R3
10R
0603
Yageo/Phycomp
RC0603FR-0710RL
R4
220k
0603
Yageo/Phycomp
RC0603FR-07K
R5
220k
0603
Yageo/Phycomp
RC0603FR-07K
R6
4.7k
0603
Yageo/Phycomp
RC0603FR-074K7L
R7
1.0k
0603
Yageo/Phycomp
RC0603FR-071KL
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 15 Rev 1.0, Dec 2018
Item
Value
Package Reference
Manufacturer
Part Number
R8
470R
0603
Yageo/Phycomp
RC0603FR-07470R
R9
470R
0603
Yageo/Phycomp
RC0603FR-07470R
R10
470R
0603
Yageo/Phycomp
RC0603FR-07470R
R11
470R
0603
Yageo/Phycomp
RC0603FR-07470R
R12
470R
0603
Yageo/Phycomp
RC0603FR-07470R
R13
4.7k
0603
Yageo/Phycomp
RC0603FR-074K7L
R14
470R
0603
Yageo/Phycomp
RC0603FR-07470R
R15
1.0k
0603
Yageo/Phycomp
RC0603FR-071KL
R16
10k
0603
Yageo/Phycomp
RC0603FR-0710KL
R17
1.0k
0603
Yageo/Phycomp
RC0603FR-071KL
R18
4.7k
0603
Yageo/Phycomp
RC0603FR-074K7L
R19
0R
0603
Yageo/Phycomp
RC0603JR-070RL
R20
62R
0603
Vishay
CRCW060362R0FKED
R21
4.7k
0603
Yageo/Phycomp
RC0603FR-074K7L
R22
4.7k
0603
Yageo/Phycomp
RC0603FR-074K7L
R23
62R
0603
Vishay
CRCW060362R0FKED
R24
0R
0603
Yageo/Phycomp
RC0603JR-070RL
R25
10k
0603
Yageo/Phycomp
RC0603FR-0710KL
R26
0R
0603
Yageo/Phycomp
RC0603JR-070RL
R27
10k
0603
Yageo/Phycomp
RC0603FR-0710KL
R28
1.3k
0603
Yageo/Phycomp
AC0603FR-071K3L
R29
100R
0603
Yageo/Phycomp
RC0603FR-07100RL
S1
Multimec
3ESH9-15.0
X1
5004
Keystone
5004
X2
5004
Keystone
5004
X3
5000
Keystone
5000
X4
5000
Keystone
5000
X5
5000
Keystone
5000
X6
PB4 Red
Hirschmann Test &
Measurement
973 582-101
X7
1935776
Phoenix Contact
1935776
X8
TSM-102-01-S-SV
Samtec
TSM-102-01-S-SV
X9
PB4 Black
Hirschmann Test &
Measurement
973 582-100
X10
TSM-103-01-L-
SV-TR
Samtec
TSM-103-01-L-SV-TR
X11
1935789
Phoenix Contact
1935789
X12
5004
Keystone
5004
X13
TSM-102-01-S-SV
Samtec
TSM-102-01-S-SV
X14
HTST-108-01-L-
DV
Samtec
HTST-108-01-L-DV
X15
TSM-103-01-L-
SV-TR
Samtec
TSM-103-01-L-SV-TR
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 16 Rev 1.0, Dec 2018
Item
Value
Package Reference
Manufacturer
Part Number
X16
TSM-103-01-L-
SV-TR
Samtec
TSM-103-01-L-SV-TR
X17
TSM-103-01-L-
SV-TR
Samtec
TSM-103-01-L-SV-TR
X18
TSM-110-03-S-DV
Samtec
TSM-110-03-S-DV
X19
TSM-102-01-S-SV
Samtec
TSM-102-01-S-SV
X20
5002
Keystone
5002
X21
5004
Keystone
5004
X22
5004
Keystone
5004
X23
TSM-103-01-T-DV
Samtec
TSM-103-01-T-DV
X24
TSM-102-01-S-SV
Samtec
TSM-102-01-S-SV
X25
5002
Keystone
5002
X26
TSM-103-01-L-
SV-TR
Samtec
TSM-103-01-L-SV-TR
X27
TSM-102-01-S-SV
Samtec
TSM-102-01-S-SV
Table 6: BOM details
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 17 Rev 1.0, Dec 2018
9 Appendix
9.1 Schematics of the Evaluation Board (TLE9461 & TLE9471)
Please find these schematics attached at the end of the document.
9.2 Layout Evaluation Board (with Overlay)
Figure 13: Overlay view of TLE9461-3ES /TLE9471-3ES
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 18 Rev 1.0, Dec 2018
9.3 Layout Evaluation Board (Top layer)
Figure 14: Top view of TLE9461-3ES / TLE9471-3ES
9.4 Layout Evaluation Board (Bottom layer)
Figure 15: Bottom layer view of TLE9461-3ES / TLE9471-3ES
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

TLE9461-3ES / TLE9471-3ES Evaluation Board
Getting Started
TLE9461-3ES / TLE9471-3ES Evaluation Board 19 Rev 1.0, Dec 2018
10 Additional Information
For testing the TLE9461-3ES / TLE9471-3ES Evaluation Board, the Infineon Toolbox needs to be
downloaded. It can be found at: https://www.infineon.com/Toolbox
Inside Infineon Toolbox, go to “Manage tools” and search for “Config Wizard for SBC”. The Config Wizard
is a powerful user interface that allows to control the SBC, including full register access.
The connection between computer and evaluation board is supported by the µIO stick. A short video
tutorial how to setup the board can be found at www.infineon.com/sbc (Lite SBC family).
For further information please contact http://www.infineon.com or your regional FAE.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Edition 2016-07-06
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2018 Infineon Technologies AG
All Rights Reserved.
LEGAL DISCLAIMER
THE INFORMATION GIVEN IN THIS APPLICATION NOTE IS GIVEN AS A HINT FOR THE
IMPLEMENTATION OF THE INFINEON TECHNOLOGIES COMPONENT ONLY AND SHALL NOT BE
REGARDED AS ANY DESCRIPTION OR WARRANTY OF A CERTAIN FUNCTIONALITY, CONDITION OR
QUALITY OF THE INFINEON TECHNOLOGIES COMPONENT. THE RECIPIENT OF THIS APPLICATION
NOTE MUST VERIFY ANY FUNCTION DESCRIBED HEREIN IN THE REAL APPLICATION. INFINEON
TECHNOLOGIES HEREBY DISCLAIMS ANY AND ALL WARRANTIES AND LIABILITIES OF ANY KIND
(INCLUDING WITHOUT LIMITATION WARRANTIES OF NON-INFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS OF ANY THIRD PARTY) WITH RESPECT TO ANY AND ALL INFORMATION GIVEN IN
THIS APPLICATION NOTE.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the
failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life
support devices or systems are intended to be implanted in the human body or to support and/or maintain and
sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other
persons may be endangered.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.