Infineon TriBoard TC3 6 Series User manual

User Manual Please read the Important Notice and Warnings at the end of this document V1.0
www.infineon.com TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard TC3X6
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
About this document
Scope and purpose
The User Manual provide information about using, configuration and connecting the TriBoard with Infineon
AURIX™ TC3X6 device. The manual provide information for different hardware types. There exist different
hardware with Through Hole socket (TriBoard TC3X6 TH) and soldered devices (TriBoard TC3X6). The
schematic is identically for the all boards if not other mentioned in chapter schematic. The placing on the boards
is slightly different on bottom side around the TC3X6 itself dependent of the space (socket need more space
and has through hole), but the most components are on the same location (only CB203, CB512 and CB520 are
rotated and slightly shifted). All figures are valid for each board if not differently mentioned.
Intended audience
Design, verfication, test and software engineers will use this document to get an understanding of the
functionality and connections of the TriBoard.

User Manual TOC-2 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
Table of Contents
About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TOC-2
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
3 TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Soldered board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Socketed board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2.1 Usable devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.2.2 Restricted usable devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.3.1 Failsafe handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.4 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.5 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.6 USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.6.1 Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.6.2 miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.7 FlexRay™ (E-RAY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.8 Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.9 MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.10 LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.11 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.12 HSCT (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.12.1 High speed with HSCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.13 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.14 Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.15 Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.16 Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.17 Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.17.1 OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.17.2 DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.17.3 DAP_SCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.17.4 High speed with DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.17.5 ETK connector (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.17.6 EmW Power (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
4 TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 HW Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.1 Default Pad State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.2 Bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2.1 General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2.2 Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
5 Signal (on board used) Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Table of Contents

User Manual TOC-3 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
Table of Contents
5.2 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.3 Config Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.4 Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.5 Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.6 Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
6 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 On Board only used signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 TC366 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.3 TC336 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
6.4 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.5 USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.6 FlexRay™ (ERAY) connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.7 CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.8 LIN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.9 HSCT connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.10 Ethernet connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.11 OCDS1 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.12 DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
6.13 ETK connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
6.14 Ethernet miniWiggler power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
7 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1 Known problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1.1 Known problems (TriBoard TC3X6 TH V1.0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1.2 Known problems (TriBoard TC3X6 V1.0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.2 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.3 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

User Manual 1-1 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
Introduction
1Introduction
We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quick
access to the capabilities of TriCore's powerful architecture.
Applications can be developed easily. The Evaluation Board is equipped with a variety of memories and
peripherals for connection to the environment. There is also an interface for the On Chip Debugging Features
(OCDS1 and DAP).
The Evaluation Board allows easily the development of TriCore applications with the corresponding tools.
Subsequently, the applications can be downloaded and can be tested with the powerful debugger software.
This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you through the
initial configuration of the TriBoard.
For detailed technical information about the TC3X6 (e.g. TC366, TC336) please refer to the User Manual of the
used device.

User Manual 2-1 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
Features
2Features
2.1 Summary of Features
– Infineon’s TC3X6 (TC366, TC336) AURIX™ 2G Controller in LFBGA-180 Package
–FlexRay™
1)
Transceivers
– High Speed CAN Transceivers (CAN-FD capable)
– USB to UART bridge
– Ethernet PHY
–SerialEeprom
–LINTransceiver
– Crystal 20MHz (default) or External Clock
– USB miniWiggler JDS for easy debugging
– 8 Low Power Status LEDs
– 8-DIP switches for configuration
– access to all pins of controller
– 100mm x 160mm (EURO-Board)
Connectors
The TC3X6 TriBoard offers a wide variety of connectors:
– Standard power connector
– Micro USB connector for ASC Interface (ASC0) and miniWiggler
– RJ45 connector for Ethernet
– 16-pin header for JTAG interface (OCDS)
– 2 x 10-pin header for DAP and DAP_SCR
– 10pin (2x5) Header for LIN Transceiver (LIN)
– 2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)
– 2 x 10pin (2x5) Header for FlexRay™ (ERAY-A and ERAY-B)
– four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals
– optional ETK connector
– optional 6pin (IEEE1394) Socket for HSCT
Components
– Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV
– Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,25 Volt)
– LED indicating safe state signal 2 from TLF35584
– LED indicating /HDRST (ESR0) active state
– LED indicating activ miniWiggler JDS
– LED switched via DAS software
– 2 x Infineon’s FlexRay™ Transceiver TLE9221SX
– 2 x Infineon’s High Speed CAN-Transceiver TLE9251VSJ
– Infineon’s LIN-Transceiver TLE 7259-3GE
– USB to UART bridge FT2232HL (FTDI)
– Single-Chip/Port 10/100M Ethernet PHYCEIVER with Auto MDX RTL8201FI-VC-CG (Realtek)
– 8 general purpose LEDs
–2KI2C Serial Eeprom with EUI-48™
2)
Node Identity (MICROCHIP)
1) FlexRay™ is a trademark of FlexRay Consortium.

User Manual 2-2 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
Features
–Resetswitch
–Enableswitch
– Generic switch
– 4-pin Dip switch
Zero Ohm Bridges
Zero Ohm resistors give the flexibility to configure the systems functionality.
2.2 Block Diagram
Figure 2-1 TriBoard Block Schematic
2) EUI-48™ is trademarked by IEEE
Micro
USB miniWiggler
OCDS1
USB
XTAL
FlexRay™
Transceiver
Transceiver
TxCAN0
TxCAN1
RxCAN0
RxCAN1
TC3X6
(e.g.
TC366,
TC336)
TriCore
CPU
PLL
CAN0
CAN1
ERAY B ERAY A
TX0
RX0
8 LED’s
(P33.4 up to P33.7,
P20.11 up to P20.14) Serial EEPROM
with EUI-48™
RMII
PHY
Twisted Pair RJ45
LIN
LIN
Transceiver
TX1
RX1
HSCT
optional
HSCT - TX/RX
I²C
WAKEUP
QSPI2
Multi Voltage Safety Micro
Processor Supply
TLF35584QV
ENA

User Manual 2-3 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
Features
2.3 Placement
Figure 2-2 TriBoard TC3X6 (TH) V1.0 Placement
U401
U 307
X406
Y3 0 1
X306
X2 0 1
U502
U501
L502
L501
C502
C501
R501
X603
D508
S502
Y401
BU 401
S201
X305 X304 X303
C303
D401 D402
T301
T302
X301X302
X601
D302 D30 3 D304 D305 D 306 D 307 D 308 D309
D505
D506
D507D504
X401
X501
S501
X604
X602
X404
U201
S202
X402
Y201
X502

User Manual 3-1 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
3 TriBoard Information
3.1 Soldered board
TriBoard TC3X6 V1.0 is the soldered board and will be available only with usable devices. Please see also chapter
Usable devices.
3.2 Socketed board
TriBoard TC3X6 TH V1.0 is the socketed board and will be available in two assembly options:
– For device with PMSLE module and without PMS module (TC336)
– For device with PMS module and without PMSLE module (TC366)
Difference between this two module is, that the PMSLE use a Switch Capacitor Regulator for the core voltage
generation which need only an external capacitor (see schematic C518, no external coil, no external p+n mosfet).
The PMS module use a Step-down Regulator which need an external p+n mosfet (see schematic Q506) and an
external coil (see schematic L503). To differentiate between the two boards have a look to C518. If assembled
then TC336 can be used otherwise only TC366.
If you get the board with TC366 and you will use the board with TC336 then you must remove R528, R529 and
R523, assemble R541 and R542 with a resistor 0R size 0603 and assemble C518 with a capacitor 1µF size 0603 (e.g.
CGA3E1X7R1E105K) otherwise the TC336 will not work.
If you get the board with TC336 and you will use the board with TC366 then you must remove R541, R542 and C518
and assemble R528, R529 and R523 with a resistor 0R size 0603.
The mentioned components are red marked in the following Figure 3-1:
Figure 3-1 Location of PMS/PMSLE components on bottom side
R 541
R542
R38 8
R381
R380
R37 8
Q301
R36 8
R382
R36 9
C320
C 317
R389
R383
R385
R370
CB311
CB312
R 386
C30 6
C205
CB20 4
C203
C204
C207
C208
R523
Q506
L503
C 520
C521
R252
R 250
R251
R253
R254
R529
R528
R 525
R371
R367
R365
R 314
R 313
R238
R 534
R511
R512
R505
R504
C510
R 502
R506
Q5 0 5
Q501
D501
C512
C511
R503
R239
X703
C517
CB203
X704
C316
C315
C 314
C 313
C312
R417
R437
R438
CB404
R40 5
R440
CB409
R416
R418
R 419 R414
R420
C406
Q40 2
Q403
C404
C405
CB410
CB411
CB412
R441
R442
C40 1
R404
C403
CB413
L402
U405
R433
C518
R 431
R208
R408
R215
R214
U306
R 521
R240
R364
R363
R362
R3 60
R211
CB310
C304
R449
R 448
R447
R445
R443
R413
D 403
R450
R422
R421
U403
Q401
R412
R415
R410
R 409
CB407
R407
U402
R406
CB406
R305
R306
R308
R309
R 315
R316
R318 R319
R301
R311
R341
R340
R32 1
R322
R 222
R22 0
R 221
R 524
R53 3
R 323
R343
CB301
CB302
CB205
CB511
CB512 CB515
CB516
CB517
CB520
R537
R307
R317
R538
R513
R53 5
R536
C515
R510
Q502
Q504
Q503
X702
X701
U301U 302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
R303
R304
R338
R330
R331
R358
R 350
R351
U303U304
R332
R334
R333
R352
R353
C519
R32 0
R21 6
R 209
CB510
R520
D50 3
D502
R231
R233 R235 R237
R241
R312
R 436
R 373
R 374
CB403
CB513

User Manual 3-2 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
3.2.1 Usable devices
Note: Note: Please check always the latest manual for complete list of usable/tested devices.
The board can be used with the following devices:
•TC366
• TC336 (not TC336DA, planned, not yet tested)
3.2.2 Restricted usable devices
•TC356
•TC336DA
– Ethernet will not work
–ERAYcan’tbeused
–CAN1can’tbeused
– Communication with TLF35584 not possible
– different pinning therefore following signals are different connected
Board signal name TC356 signal name TC336DA signal name
P00.0 P10.3 P10.3
P00.1 P02.1 P02.1
P00.2 P10.2 P10.2
P00.3 P50.7 P50.7
P00.4 P50.6 P50.6
P00.5 P10.7 P10.7
P00.6 P10.8 P10.8
P00.7 P50.9 P50.9
P00.8 P50.8 P50.8
P00.9 P50.11 P50.11
P00.12 P50.10 P50.10
P02.0 NC NC
P02.1 P50.0 P50.0
P02.2 P50.1 P50.1
P02.3 NC NC
P02.4 P50.3 P50.3
P02.5 P50.2 P50.2
P02.6 P50.4 P50.4
P02.7 P50.5 P50.5
P02.8 P10.1 P10.1
P10.0 P11.12 P11.12
P10.1 P11.8 P11.8
P10.2 P11.10 P11.10
P10.3 NC NC

User Manual 3-3 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
P10.4 P11.7 P11.7
P11.3 P11.4 P11.4
P11.6 P11.15 P11.15
P11.8 P11.11 P11.11
P11.9 P11.6 P11.6
P11.10 P11.5 P11.5
P11.11 P11.3 P11.3
P11.12 P11.9 P11.9
P13.0 P11.0 P11.0
P13.1 P11.1 P11.1
P13.2 P12.1 P12.1
P13.3 P11.14 P11.14
P14.8 P11.13 P11.13
P14.10 P12.0 P12.0
P15.7 NC NC
P15.8 NC NC
P22.0 NC NC
P22.1 NC NC
P22.2 NC NC
P22.3 NC NC
P23.3 NC NC
AN0 NC NC
AN4 AN0 AN0
AN5 NC AN4
AN6 NC AN5
AN7 AN10 AN10
AN9 NC AN13
AN10 AN12 AN12
AN12 NC AN21
AN13 NC AN14
AN14 NC AN9
AN15 NC AN15
AN16 P02.3 P02.3
AN17 P00.0 P00.0
AN24 P02.8 P02.8
AN25 P02.6 P02.6
AN32 P02.0 P02.0
AN33 P02.7 P02.7
AN34 NC AN20
Board signal name TC356 signal name TC336DA signal name

User Manual 3-4 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
3.3 Power Supply
All needed voltages are generated via Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV and via
the microcontroller itself (+1,25V).
The supply device is available as two different devices:
TLF35584QVVS1 -> +5V standby voltage, +5V TriCore supply (V_UC)
TLF35584QVVS2 -> +3,3V standby voltage, +3,3V TriCore supply (V_UC)
Dependent of the assembled device the board works with 5V or 3,3V IO.
The TLF35584QV provide the following voltages:
+3,3V or +5V for standby (connected to VEVRSB)
+3,3V or +5V for TriCore (connected to VEXT)
+5V communcation supply (used by CAN and FlexRay™ transceivers)
+5V voltage reference (connected to VDDM and VAREFx)
+3,3V via LDO directly from pre regulator (used by Ethernet PHY)
Applying a stable supply voltage causes the power on reset after a short period. The three LED's (V_UC, +3.3V,
+1V25) indicate the status of the on board generated voltages.
A manual power on reset is executed by pressing the reset button.
The Board has to be connected to a +3,5V to +40V DC power supply.
The power consumption is not specified yet but a supply with 12V and 500mA is recommended. The pinout for
the supply connector is shown in Figure 6-5. There can be used any standard power pack with a connector where
the positive line is surrounded by the ground line.
3.3.1 Failsafe handling
In case that the device don’t contains a program which disable or service the window watchdog and error pin
monitor of the TLF35584 then the TLF35584 is going to a FAILSAFE state where all supplies are switched off. This
state can be left via reconnect the power plug or via the ENA button (S502). In this case you must connect a
debugger which is able to disable the window watchdog and error pin monitor to reprogram the microcontroller.
In the default state of the board the switching to FAILSAFE state is switched off via resistor R508.
If you will use/evaluate all safety features of the TLF35584 make sure that R509 is assembled and R508 is not
assembled. Make sure that you have a proper initialization of TLF35584 in your softare.
Resistor R508 and R509 are red marked in the following Figure 3-2:
AN35 NC AN16
AN36 P02.4 P02.4
AN37 P02.5 P02.5
AN38 P02.2 P02.2
AN39 NC AN17
Board signal name TC356 signal name TC336DA signal name

User Manual 3-5 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
Figure 3-2 Resistors for TLF35584 Safety feature handling with switch on
3.4 LEDs
There are 15 LEDs on board:
– D302 up to D305 (blue) -> toogle LEDs connected to P33.4 ... P33.7
– D306 up to D309 (blue) -> toogle LEDs connected to P20.11 ... P20.14
– D504 RST (red) -> RESET LED indicate the reset state of the board (/ESR0)
– D505 +1V25 (green) -> +1V25 power supply indication
– D506 +3V3 (green) -> +3,3V power supply indication
– D507 V_UC (green) -> +5V/+3,3V power supply indication
– D508 SS2 (green) -> safe state signal 2 indication
– D402 ACT (green) -> on board miniWiggler JDS is ACTIV
– D401 RUN (blue) -> Debug RUN mode (switched by DAS Server)
3.5 Clock
On the board is a fixed crystal with 20MHz assembled. You can change this by replacing Y101 (soldered).
3.6 USB Connector
The USB connector is used for connection to a PC. Via the USB it is possible to power the board, using the ASCLIN0
as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 6-6.
NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. For
actual DAS software please contact your local FAE.
The software can also be found on:
DAS website
R379 R372
C305
C310
CB313
CB314
CB315
C311
U307
Y301
R375
R376
CB316
CB317
U308
C516
X306
X201
U502
C505
U501
L502
L501
CB501
C502
C507
C 509
C508
C501
C503
C504
R501
R507
R508
R509
CB502
X603
D508
S502
R402
R403
CB408
Y401
U401 CB401
R401
L401
BU 4 0 1
C402
CB405
X406
R457
R249
R248
R246 R245
R244
X402
S201
R377
CB202
R204
R205
X305 X304 X303
R236
R234 R232 R230
R361
R359
R212
D301
C303
U408
U407
U406
R451
R 455
R456
R454
R446
R444
CB419
CB418
CB417 CB416
CB415 CB414
D401
R430
R429
R423
R411
D402
U404
CB402
R344
R424
R425 R426
R427
R428
R201
R203
R202
C201
C202
R206
R207
Y201
R337R357
R324
R399
R391
R392 R393 R394 R3 95 R3 96 R39 7
CB309
R532
C301C302
R439
R531
R335
R336
R 355
R356
U305
T301T302
X301X302
X601
D302 D303 D304 D305 D306 D307 D308 D309
D505
D506
D507D504
X401
X5 0 1
S501
R354
R452
R213
CB201
R398
R255
R256
R390
R348
R349
X502
X604
R346
R 347
X602
X404
U201
S202

User Manual 3-6 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
3.6.1 Serial Connection to PC
After the first connection of USB to a PC the needed driver will be installed automatically. During this there will
be created a new COM port on PC. This COM port can be used to communicate with the board via ASCLIN0 of the
device. Per default the ASCLIN0 is used on P14.0 and P14.1 (e.g. Generic Bootstrap Loader) . In case you will use
the Generic Bootstrap Loader via CAN or ASCLIN0 via P15.2 and P15.3 you must:
– remove R436 and R437 (this disconnect the serial connection from P14.0 and P14.1)
– remove R301 and R302 (this disconnect the CAN0 transceiver from P20.7 and P20.8)
– assemble R438 and R440 with 0R resistor (size 0603) to connect P15.2 and P15.3 to serial connection
– assemble R303 and R304 with 0R resistor (size 0603) to connect P14.0 and P14.1 to CAN0 transceiver
The mentioned resistors are red marked in Figure 3-3.
Figure 3-3 Resistors for ASC connection (ASC0)
3.6.2 miniWiggler JDS
The miniWiggler JDS is a low cost debug tool which allows you access to the JTAG of the device. Make sure that
you have the latest DAS release. Debugging is possible via the DAS Server ‘UDAS‘. Please contact your prefered
debug vendor for support of DAS.
If you have connected the board to the PC and there runs the DAS server, then a working connection is visible via
the green ACTIV LED.
The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client).
IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and X402 (DAP) if the
ACTIV LED is on.
R541
R542
R388
R381
R380
R378
Q301
R36 8
R382
R36 9
C320
C317
R389
R383
R385
R370
CB311
CB312
R 386
C30 6
C205
CB20 4
C203
C204
C207
C208
R523
Q50 6
L503
C 520
C521
R252
R250
R251
R253
R254
R529
R528
R525
R371
R367
R365
R 314
R313
R238
R534
R511
R512
R505
R504
C510
R502
R506
Q5 0 5
Q501
D501
C512
C511
R503
R239
X703
C517
CB203
X704
C316
C315
C 314
C313
C312
R417
R437
R438
CB404
R40 5
R440
CB409
R416
R418
R 419 R414
R420
C406
Q40 2
Q403
C404
C405
CB410
CB411
CB412
R441
R442
C40 1
R404
C403
CB413
L402
U405
R433
C518
R431
R208
R408
R 215
R21 4
U306
R 521
R240
R364
R363
R362
R3 60
R211
CB310
C304
R449
R 448
R447
R445
R443
R413
D 403
R450
R422
R421
U403
Q401
R412
R415
R410
R409
CB407
R407
U402
R40 6
CB406
R30 5
R306
R308
R309
R315
R31 6
R318 R319
R301
R311
R341
R340
R32 1
R322
R222
R22 0
R 221
R524
R53 3
R 323
R343
CB301
CB302
CB205
CB511
CB512 CB515
CB516
CB517
CB520
R537
R307
R317
R538
R513
R53 5
R536
C515
R510
Q50 2
Q5 0 4
Q503
X702
X701
U30 1U302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
R303
R304
R338
R330
R331
R358
R 350
R351
U303U304
R332
R334
R333
R352
R353
C519
R32 0
R216
R209
CB510
R520
D50 3
D502
R231
R233 R235 R237
R241
R312
R 436
R373
R374
CB403
CB513

User Manual 3-7 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
Per default the miniWiggler is connected to the DAP. If resistors R214, R215 and R216 assembled (default) then
the standard DAP is connected to miniWiggler. If all this resistors are not assembled then the miniWiggler can’t
be used. In this case only the DAP connectors X402 and X406 can be used. See Figure 3-8.
3.7 FlexRay™ (E-RAY)
The board has 2 IDC10 plugs for FlexRay™ Communication (channel A and B) with up to 10 Mbit/s. For the pinout
of the plugs see Figure 6-7. You can use a IDC female connector with crimpconnector, flat cable and SUB-D 9 plug
with crimpconnector to have a 1:1 adapter to SUB-D 9.
The transceiver are connected to the TriCore device via zero ohm resistors (R320 up to R324 and R340 up to R344)
which must be removed to use the ports outside.
ERAY-A can be connected to P02.0, P02.1 and P02.4. Transceiver for channel A can be enabled/disabled via P10.1.
The error state of transceiver channel A can be read out via P10.2.
ERAY-B is connected to P02.2, P02.3 and P02.5. Transceiver for channel B can be enabled/disabled via P20.10. The
error state of transceiver channel A can be read out via P20.9.
For more information look in the user manual for TC3X6.
3.8 Serial Eeprom
Note: TC336 don’t have I2C module. Access to the eeprom only with simulation of I2C protocol via bit banging
possible.
The I2C via P15.4 and P15.5 of the TC3X6 is connected to a serial EEPROM with a size of 2KBit (2 x 128 x 8). The slave
address of this EEPROM is 0x50. The upper half of the array (80h-FFh) is permanently write-protected. Write
operations to this address range are inhibited. Read operations are not affected. This upper half contains a pre-
programmed EUI-48™ node address which can be used as MAC ID for Ethernet. The other 128 bytes are writable
by customer.
To disconnect (disable) the EEPROM remove resistor R348 and R349.
3.9 MultiCAN
On the board are two CAN transceiver connected to the CAN0 and CAN1 of TC3X6. The transceivers are connected
to two IDC10 plug. For the pinout of IDC10 plug see Figure 6-8. You can use a IDC female connector with
crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
The transceiver are connected to the TriCore device via zero ohm resistors (R301 up to R304 and R311 up to R314)
which must be removed to use the ports outside.
CAN0 can be used via P20.7 and P20.8 (CAN0 node 0, default) or P14.0 and P14.1 (CAN0 node 1). CAN1 can be used
via P00.4 and P00.5 (CAN1 node 1, default) or P00.0 and P00.1 (CAN1 node 0).
3.10 LIN
On the board is one LIN transceiver connected to the ASCLIN1 on TC3X6 (P15.0 and P15.1). The transceiver are
connected to one IDC10 plug. For the pinout of IDC10 plug see Figure 6-9. You can use a IDC female connector with
crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
To disconnect the LIN remove resistor R364 and R365.
The LIN can be used in master and in slave mode. For the master mode there is per default a pull-up of 1K (R360)
and a capacitor of 1nF (C304) on the BUS assembled. For using the LIN in slave mode the pull-up resistor R360
must be removed and maybe the capacitor changed to a smaller value (e.g. 220pF).
The mentioned resistor and capacitor are red marked in Figure 3-4

User Manual 3-8 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
Figure 3-4 Components for LIN Master Mode
3.11 Ethernet
The TriBoard provide a RJ45 connector (X306) for twisted pair ethernet connections.The TriBoard use a Realtek
Single-Chip/Port 10/100M Ethernet PHYCEIVER with Auto MDX RTL8201FI-VC-CG as physical interface device. For
more information about the ethernet modul see TC3X6 User’s Manual, about the PHY see the RTL8201FI
datasheet. For the pinout of RJ45 see Figure 6-11.
The PHY is connected to the TriCore device via resistors and resistor arrays (R368 up to R374) which must be
removed to use the ports outside.
For the connection between TriCore and PHY is used RMII.
For MD connection there is used P00.0 and P02.8. To use this communication way please make sure that R376 is
not assembled (default). For R376 position please see also Figure 4-4.
Note: Please note that the RGMII interface can’t be used of limited pin availability. Therefore Gigabit is not
usable with this board only 10M and 100M.
Note: TC336 don’t support ethernet.
3.12 HSCT (optional)
The TriBoard provide a footprint of IEEE 1394 socket (X201) for connection to other TC3XX via HSCT.
Note: Don’t use X201 for connection to any IEEE 1394 device,
this can destroy the board and/or the connected device.
R541
R542
R38 8
R381
R380
R37 8
Q301
R36 8
R382
R36 9
C320
C317
R389
R383
R385
R370
CB311
CB312
R 386
C30 6
C205
CB20 4
C203
C204
C207
C208
R523
Q50 6
L503
C 520
C521
R252
R250
R251
R253
R254
R529
R528
R525
R371
R367
R365
R 314
R313
R238
R534
R511
R512
R505
R504
C510
R 502
R506
Q5 0 5
Q501
D501
C512
C511
R503
R239
X703
C517
CB203
X704
C316
C315
C 314
C313
C312
R417
R437
R438
CB404
R40 5
R440
CB409
R416
R418
R 419 R414
R420
C406
Q40 2
Q403
C404
C405
CB410
CB411
CB412
R441
R442
C40 1
R404
C403
CB413
L402
U405
R433
C518
R431
R208
R408
R215
R214
U306
R 521
R240
R364
R363
R362
R3 60
R211
CB310
C304
R449
R 448
R447
R445
R443
R413
D 403
R450
R422
R421
U403
Q401
R412
R415
R410
R409
CB407
R407
U402
R406
CB406
R305
R306
R308
R309
R315
R316
R318 R319
R301
R311
R341
R340
R32 1
R322
R 222
R22 0
R 221
R524
R53 3
R 323
R343
CB301
CB302
CB205
CB511
CB512 CB515
CB516
CB517
CB520
R537
R307
R317
R538
R513
R53 5
R536
C515
R510
Q50 2
Q50 4
Q503
X702
X701
U301U302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
R303
R304
R338
R330
R331
R358
R350
R351
U303U304
R332
R334
R333
R352
R353
C519
R32 0
R21 6
R209
CB510
R520
D50 3
D502
R231
R233 R235 R237
R241
R312
R 436
R373
R374
CB403
CB513

User Manual 3-9 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
For connect two TriBoards you need to assemble this socket (Lumberg 2415 01) on each board and connect the
boards with a standard 6 pin IEEE 1394 cable. For the pinout of socket see Figure 6-10.
Note: TC336 don’t support HSCT.
3.12.1 High speed with HSCT
For use the HSCT connection between two board you need to remove 5 resistors to have a very short connection
between device and connector. On the TC3X6 Triboard this 5 resistors are R250, R251, R252, R253 and R254 (red
marked in Figure 3-5). This resistors needs to be removed.
mportant: When the resistors are removed then the port signals P20.0, P21.2, P21.3, P21.4 and P21.5 are no
longer available on the 80 pin samtec connectors.
Figure 3-5 Resistors for high speed HSCT
3.13 ADC
On this boards are 5 ADC channels prepared with a low pass filter. On pin AN7, AN24, AN25, AN36 and AN37 is
assembled a capacitor of 47nF and a serial resistor of 4,7K. The filter components are red marked in the following
figures (Figure 3-6 and Figure 3-7).
Note: AN24 adn AN25 are not connected on TC336 and therefore not usable.
R541
R542
R38 8
R381
R380
R37 8
Q301
R36 8
R382
R36 9
C320
C 317
R389
R383
R385
R370
CB311
CB312
R 386
C30 6
C205
CB20 4
C203
C204
C207
C208
R523
Q50 6
L503
C 520
C521
R252
R 250
R251
R253
R254
R529
R528
R 525
R371
R367
R365
R314
R313
R238
R534
R511
R512
R505
R504
C510
R502
R506
Q5 0 5
Q501
D501
C512
C511
R503
R239
X703
C517
CB203
X704
C316
C315
C 314
C313
C312
R417
R437
R438
CB404
R40 5
R440
CB409
R416
R418
R 419 R414
R420
C406
Q40 2
Q403
C404
C405
CB410
CB411
CB412
R441
R442
C40 1
R404
C403
CB413
L402
U405
R433
C518
R 431
R208
R408
R215
R214
U306
R 521
R240
R364
R363
R362
R3 60
R211
CB310
C304
R449
R448
R447
R445
R443
R413
D 403
R450
R422
R421
U403
Q401
R412
R415
R410
R409
CB407
R407
U402
R406
CB406
R305
R306
R308
R309
R 315
R316
R318 R319
R301
R311
R341
R340
R32 1
R322
R 222
R22 0
R221
R 524
R53 3
R 323
R343
CB301
CB302
CB205
CB511
CB512 CB515
CB516
CB517
CB520
R537
R307
R317
R538
R513
R53 5
R536
C515
R510
Q50 2
Q504
Q503
X702
X701
U301U 302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
R303
R304
R338
R330
R331
R358
R 350
R351
U303U304
R332
R334
R333
R352
R353
C519
R32 0
R21 6
R209
CB510
R520
D50 3
D502
R231
R233 R235 R237
R241
R312
R436
R 373
R 374
CB403
CB513

User Manual 3-10 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
Figure 3-6 Filter components of ADC channels on Top Side
Figure 3-7 Filter components of ADC channels on Bottom Side
R379 R372
C305
C310
CB313
CB314
CB315
C311
U307
Y301
R375
R376
CB316
CB317
U308
C516
X306
X2 0 1
U502
C505
U501
L502
L501
CB501
C502
C507
C 509
C508
C501
C503
C504
R501
R507
R508
R509
CB502
X603
D508
S502
R 402
R403
CB408
Y401
U401 CB401
R401
L401
BU 4 0 1
C402
CB405
X406
R457
R249
R248
R246 R245
R244
X402
S201
R377
CB202
R204
R205
X305 X304 X303
R236
R234 R232 R230
R361
R359
R212
D301
C303
U408
U407
U406
R451
R 455
R456
R454
R446
R444
CB419
CB418
CB417 CB416
CB415 CB414
D401
R430
R429
R423
R411
D402
U404
CB402
R344
R424
R425 R426
R427
R428
R201
R203
R202
C201
C 202
R206
R207
Y201
R337R357
R324
R399
R391
R392 R393 R394 R3 95 R3 96 R39 7
CB309
R532
C301C302
R439
R531
R335
R336
R 355
R356
U305
T301T302
X301X302
X601
D302 D303 D304 D305 D306 D307 D308 D309
D505
D506
D507D504
X401
X5 0 1
S501
R354
R452
R213
CB201
R398
R255
R256
R390
R348
R349
X502
X604
R346
R347
X602
X404
U201
S202
R541
R542
R38 8
R381
R380
R37 8
Q301
R36 8
R382
R36 9
C320
C 317
R389
R383
R385
R370
CB311
CB312
R 386
C30 6
C205
CB20 4
C203
C204
C207
C208
R523
Q50 6
L503
C 520
C521
R252
R 250
R251
R253
R254
R529
R528
R525
R371
R367
R365
R314
R313
R238
R 534
R511
R512
R505
R504
C510
R 502
R506
Q5 0 5
Q501
D501
C512
C511
R503
R239
X703
C517
CB203
X704
C316
C315
C 314
C313
C312
R417
R437
R438
CB404
R40 5
R440
CB409
R416
R418
R 419 R414
R420
C406
Q40 2
Q403
C404
C405
CB410
CB411
CB412
R441
R442
C40 1
R404
C403
CB413
L402
U405
R433
C518
R 431
R208
R408
R215
R214
U306
R 521
R240
R364
R363
R362
R3 60
R211
CB310
C304
R449
R448
R447
R445
R443
R413
D 403
R450
R422
R421
U403
Q401
R412
R415
R410
R409
CB407
R407
U402
R406
CB406
R305
R306
R308
R309
R 315
R316
R318 R319
R301
R311
R341
R340
R32 1
R322
R 222
R22 0
R 221
R 524
R53 3
R 323
R343
CB301
CB302
CB205
CB511
CB512 CB515
CB51 6
CB517
CB520
R537
R307
R317
R538
R513
R53 5
R536
C515
R510
Q50 2
Q504
Q503
X702
X701
U301U 302
R302
R342
CB303
CB304
CB305
CB306
CB307
CB308
R303
R304
R338
R330
R331
R358
R 350
R351
U303U304
R332
R334
R333
R352
R353
C519
R32 0
R21 6
R 209
CB510
R520
D50 3
D502
R231
R233 R235 R237
R241
R312
R436
R373
R 374
CB403
CB513

User Manual 3-11 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
3.14 Other peripherals
For all other peripherals there are no special plugs on the board. The peripheral signals are available on the
different connectors. See
“Connector Pin Assignment” on Page 6-1 .
3.15 Toggle LED’s
The status LED’s are low active and can be controlled by Software.
Port 20 pin 11 up to pin 14 are connected to single LED’s (D306... D309) and powered by the normal
microcontroller voltage.
Port 33 pin 4 up to pin 7 are connected to single LED’s (D302... D305) and powered by the standby voltage. This
means that this LED’s can be are activ also when the board is in standby mode and only the standby voltage
available (port 33 is powered by VEVRSB pin which is connected to standby supply of TLF35584). In this case the
port pins are controlled by the standby controller if available.
3.16 Buttons
On the board are three buttons.
The reset button (S501) will apply a warm power on reset to the device.
The ENA button (S502) will be used to enable/wakeup the TLF35584.
The P33.11 button (S202) can be used by software as input. Also can this button used by the standby controller
to react on an event when only standby supply is available (e.g. wakeup the TLF35584 via P33.10).
3.17 Debug System
3.17.1 OCDS1
The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of Microcontroller (+5V
default or +3,3V). For pinout of the connector see Figure 6-12. You can connect any debugger to this connector.
The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals in the connector then
assemble R424 and R425 or R426 with a 0R resistor.
If you connect a debug hardware make sure that the miniWiggler JDS (see “miniWiggler JDS” on Page 3-6) is not
activ (ACTIV LED is off) and on the DAP connector (X402) is no hardware connected or the hardware is tristated.
If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB connection to the PC.
If R214 up to R216 not assembled then the connector is not usable.
3.17.2 DAP
The board comes with a DAP connector (X402). For pinout of this connector see Figure 6-13. You can connect a
DAP hardware here. If you use this connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off)
and a connected OCDS1 hardware is disconnected or tristated.
3.17.3 DAP_SCR
Additional DAP connector (X406) is connected to DAP_SCR. This DAP can be used as private DAP connection to
the standby controller. For pinout of this connector see Figure 6-15. You can connect a DAP hardware here. This
DAP use P33.6 and P33.7 which are connected to LED on the board. Maybe it is necessary to remove R393 and
R394 if the speed of the connection is not fast enough.

User Manual 3-12 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
3.17.4 High speed with DAP
For use the DAP connection with 160 MHz you need to remove 3 resistors to have a very short connection between
device and connector. On the TC3X6 Triboard this 3 resistors are R214, R215 and R216 for DAP (red marked in
Figure 3-8). This resistors needs to be removed.
Important: When the resistors are removed then only the DAP connector on the board can be used. The on board
wiggler and the OCDS1 connector couldn’t be use (are disconnected) in this case, also the DAP/JTAG part of the
ETK connector couldn’t be used.
All resistors are red marked in the following figure:
Figure 3-8 Location of DAP resistors on Top Side
3.17.5 ETK connector (optional)
The TriBoard provide a 10 pin samtec connector (X404) for connecting to an ETK. This connector should be
assembled by your self if needed.
For the pinout of connector see Figure 6-14.
The needed Samtec connector is: TFM-105-02-A.
3.17.6 EmW Power (optional)
The TriBoard provide the 4 pin power connector (X502) for the Ethernet miniWiggler (EmW). This connector
should be assembled by your self if needed.
For the pinout of connector see Figure 6-15.
The needed Samtec connector is the JST B4B-PH-K.
The connector provide the input voltage to the Ethernet miniWiggler and an enable/wakeup signal connected to
TLF35584.
R 541
R542
R388
R381
R380
R378
Q301
R368
R382
R369
C320
C317
R389
R383
R385
R370
CB311
CB312
R 386
C306
C205
CB204
C203
C204
C207
C208
R523
Q50 6
L503
C 520
C521
R252
R 250
R251
R253
R254
R529
R528
R525
R371
R367
R365
R314
R313
R238
R534
R511
R512
R505
R504
C510
R502
R506
Q5 0 5
Q501
D501
C512
C511
R503
R239
X703
C517
CB20 3
X704
C316
C315
C314
C313
C312
R417
R437
R438
CB404
R405
R440
CB40 9
R416
R418
R419 R414
R420
C406
Q40 2
Q403
C404
C405
CB410
CB41 1
CB412
R441
R442
C40 1
R404
C403
CB413
L402
U405
R433
C518
R431
R208
R408
R 215
R21 4
U306
R521
R240
R364
R363
R362
R3 60
R211
CB310
C304
R449
R448
R447
R445
R443
R413
D 403
R450
R422
R421
U403
Q401
R412
R415
R410
R409
CB407
R407
U402
R40 6
CB40 6
R30 5
R306
R308
R309
R315
R31 6
R318 R319
R301
R311
R341
R340
R321
R322
R 222
R220
R 221
R524
R533
R323
R343
CB301
CB302
CB20 5
CB511
CB51 2 CB515
CB516
CB517
CB52 0
R537
R307
R317
R538
R513
R535
R536
C515
R510
Q502
Q5 0 4
Q503
X702
X701
U30 1U302
R302
R342
CB30 3
CB30 4
CB30 5
CB30 6
CB307
CB308
R303
R304
R338
R330
R331
R358
R 350
R351
U303U304
R332
R334
R333
R352
R353
C519
R320
R216
R209
CB510
R520
D503
D502
R231
R233 R235 R237
R 241
R312
R436
R373
R374
CB403
CB513

User Manual 3-13 V1.0
TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0 2019-09
TriBoard Manual TC3X6
Hardware: TriBoard TC3X6 TH V1.0 and TriBoard TC3X6 V1.0
TriBoard Information
Because the device don’t have a VDDSB pin the 1,25V standby supply pin of the connector is not connected to the
device only to pin 75 of connector X602 and X702 on this board.