InfiRay Xclip User manual

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
InfiRay Technologies Co., Ltd.
Xclip ——Thermal Imaging Attachment
User Manual

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
Contents
1. Description ............................................................................................................ 3
2. Components and Controls ...................................................................................... 3
2.1 Components ................................................................................................. 4
2.2 Controls ....................................................................................................... 5
3. Menu/Status Bar Icons .......................................................................................... 6
4. Specifications ........................................................................................................ 7
4.1 Configuration Parameters ............................................................................. 7
4.2 Monocular Eyepiece Parameters .................................................................. 8
5. System Function .................................................................................................... 8
6. Operation System .................................................................................................. 9
6.1 Power on / Power off ................................................................................... 9
6.2 Standby Mode .............................................................................................. 9
6.3 Status bar ..................................................................................................... 9
6.4 Shortcut Menu ............................................................................................. 9
6.5 Advanced Menu ......................................................................................... 10
6.6 Image Calibration (Only for Attachment) ................................................... 12
7. Preventative Maintenance ..................................................................................... 13
7.1 Battery Replacement .................................................................................. 13
7.2 Product Cleaning and Maintenance ......................................................... 14
7.3 Safety Regulation ....................................................................................... 14
8. General Trouble Shooting ..................................................................................... 15
9. Appendix .............................................................................................................. 16
9.1 User Interface Description ......................................................................... 16
9.2 Product Dimensions ................................................................................... 17
9.2.1 Boundary Dimension ....................................................................... 17
9.2.2 Bottom Mounting Hole Size ............................................................ 17

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
1. Description
Xclip is a multifunctional thermal imager device equipped with two kinds of
eyepiece that can be used either as a monocular or a front attachment as the infrared
expansion device of white light. Different from the night vision device based on image
enhancement, Xclip doesn’t need external light source and isn’t influenced by strong
light exposure. It can be used in the night or bad weather conditions such as fog, rain,
smog and detect the objective through barriers such as branch, top grass, thick bush and
so on. Xclip has a wide range application including night hunting, observation and
terrain orientation, search and rescue operations.
Figure 1-1 Xclip thermal imaging attachment
2. Components and Controls
Figure 2.1 Function introduction

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
2.1 Components
No. Name Function description
① Lens Cap Protecting the lens and using for external correction
② Objective Lens ——
③ Lens Focus Ring
It is used to adjust the focal length of objective lens to make
the image to be the clearest when the image is indistinct.
④ Battery Compartment Cover
Using two batteries which are CR123, CR123A or 16340 to
supply power.
⑤ Monocular
Eyepiece Locking
Ring Fixing the monocular eyepiece on device body.
⑥ Monocular Eyepiece Diopter
Adjustment Ring
Adjusting the diopter of monocular
eyepiece to suit different
eyesight.
⑦ Eye Shade ——
⑧ Front Attachment Eyepiece Selecting front eyepiece as the infrared expansion attachment
of white light sight
⑨ Front Lens Clamping Ring
for Adapter Ring
Used to lock the adapter
ring between the white light sight and
the attachment
⑩ Front Lens Locking Ring Locking the front eyepiece to device body.
⑪ Type-C Interface Used for data communication and external power supply
⑫ Power button Power on/Power off/Standby/Up/Left
⑬ Menu(M) Button Entering menu/Parameter switch
⑭ Correction(C) Button Shutter correction/Background correction /Down/Right

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
2.2 Controls
Operation in normal display mode Operation in menu mode/calibration interface
Short Press Long Press Short Press Long Press
Power (12)
Button
Standby/
Awaken
Power on /
Power off
Power (12)
Button
Adjust parameter
and scroll up
options
——
M (13)
Button
Open the
shortcut menu
Open advanced
menu
M (13)
Button
Function
switch/Parameter
selection
★
Save and exit
menu
C (14)
Button
Shutter
correction
Background
correction
C (14)
Button
Adjust
parameter/Scrolling
down options
——
M (13)
Button
+ C (14)
Button
——
Enter image
calibration
interface
Power (12)
Button Up/Left shift Up/Left quick shift
M (13)
Button X/Y shift Save and exit
C (14)
Button Down/Right shift Down/Right quick shift
★
Under the shortcut menu, short press to switch functions; Under the advanced menu, short press to
switch the parameter options.

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
3. Menu/Status Bar Icons
Screen Lightness Setup，four levels
Image Mode: B(Black hot)、W（White hot）、R（Red hot）、C
（Pseudo Color）
E-zoom (Only for Monocular: ×1, ×2, ×4)
Ultraclear Mode
Bluetooth Option
Bluetooth on
Video Out Option
Video Out On
Battery Type Selection
Blind Pixel Correction Option
Factory Reset
Battery Capacity Indicator
Type-C Power Supply
Orientation Shift

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
4. Specifications
4.1 Configuration Parameters
Model Xclip CL42
Detector Parameters
Detector Type VOx Uncooled
Resolution 384*288
Pixel Size 17um
NETD ≤50mk
Frame Rate 50Hz
Optics Parameters
Objective Lens 42mm
Field of View 8.9°×6.7°
Magnification Attachment: 1×; Monocular: 2.9×-11.6×
Detection Range
(Target size
：
1.7m×1.2m)
Detection
：
2100m
（
2 pixels
）
Recognition
：
700m
（
6 pixels
）
Display
Type OLED
Resolution 1024×768
Electrical Parameters
Battery CR123×2
Power Consumption
＜
1500mW
Max. Battery Life 4hr
External Interface
USB Interface Type-C
Video Output PAL (RCA Port)
External Power Type-C
Functions

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
Electric Compass √
Accelerometer √
Remote Control Bluetooth
Replaceable Parts M18 Monocular Eyepiece
Physic Parameters
IP Rating IP67
Weight (without batteries)
＜
420g
Dimension 154mm×61mm×58mm
Adapter Ring M52×0.75
4.2 Monocular Eyepiece Parameters
Monocular Eyepiece Parameters
Eyepiece Model
M18
Magnification
2.9×-11.6×
Eye Relief
20mm
Diopter Adjustment
-5D
～
+5D
Weight
70g
5. System Function
● Quick conversion between attachment and monocular；
● Quick mounting and removal of attachment
● Detection range above 1.5km；
● 1024×768 high resolution OLED display；
● Bluetooth remote control；
● Four image modes – white hot, black hot, red hot, pseudo color;
● Monocular's digital zoom：×1、×2、×4；
● Type-C interface power supply and data transmission;

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
● Build-in Bluetooth, compass, leaser, motion sensor;
● IP67 protection level；
● Compact size；
● Light weight and high impact resistance;
6. Operation System
6.1 Power on / Power off
In shutdown mode, long press Power (12) button for 3s to start up the device. And,
device is started.
And then Long press Power (12) button for about 5s to shut down the device.
6.2 Standby Mode
Enter/exit the standby mode with short pressing the Power (12) button for power
saving.
6.3 Status bar
The status bar is located at the bottom of the screen, which shows information such
as image mode, screen lightness level, Bluetooth activated, E-zoom, video out activated,
battery status.
6.4 Shortcut Menu
In the normal display mode, short press M (13) button to switch the order of "no
menu - screen brightness - image mode - electronic zoom - exit shortcut menu", and by
pressing Power (12) button and the C (14) key to adjust the parameters of each function.
Shortcut menu interface is as shown in figure 6-1.
● Screen lightness：1~4 lightness level;
● Image mode: W (White hot), B (Black hot), R (Red hot), C (pseudo color);
● E-zoom: ×1、×2、×4, only monocular.

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
Figure 6-1 Shortcut Menu
6.5 Advanced Menu
Long press the M (13) button for 3s to enter the advanced menu interface, as shown
in figure 6-2. From top to bottom the six function options are Ultraclear mode,
Bluetooth, video out, buttery type, blind pixel correction, factory reset, referring to table
6-1 for details.
Operations:
 Under the advanced menu, short press M (13) button to adjust the parameters of
present option or enter the secondary menu.
 Power (12) button is used to shift “up” or “left”, C (14) button is used to shift
“down” or “right”;
 Long pressing M (13) button for 3s to exit advanced menu interface.

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
Figure 6-2 Advanced menu interface
Table 6-1 Xclip advanced menu function description
Icon Name Function Description Status
U
ltraclear
Mode ON/OFF
In this mode, the image contrast is
enhanced, which is suitable for
cloudy, rainy, foggy and other harsh
weather conditions
The icon
displays on
the status bar.
Bluetooth
ON/OFF
When Bluetooth is on, it can be
operated with the bluetooth remote
control or mobile phone APP
( please search for connection by
mobile phone within 1 minute,
otherwise, the bluetooth will be
automatically turned off ).
The icon
displays on
the status bar.
Video
Output ON/OFF Transfer the analog video in pal through the Type-C data cable.
The icon
displays on
the status bar.

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
Battery
Type 3V/3.7V
3.7v is selected for charging type
batteries, and 3V is for normal dry
batteries.
——
Blind
pixel
correction
Calibrate
the blind
pixels on
the image
Short press M button to enter blind
pixel correction interface. After
selecting the blind pixel, press
Power(12) button and C button at
same time to correct the blind
pixels.
Blind pixel
calibration
interface
（shown in
figure 5-3）
Factory
reset
Restore
factory state
Y: Confirm，N：Cancel
Then long press M button to save
and exit.
——
Figure 6-3 Blind pixel correction interface
6.6 Image Calibration (Only for Attachment)
When Xclip is installed on the white light sighting tool as an infrared extension
component, if the cross division of the white light sighting is not in the center of the
infrared image, the image calibration function can be used to shift the infrared image

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
to ensure the position consistency between the white light image and the infrared
image.
Operation:
Step 1: In normal display mode, press the M (13) button and C (14) button for 3s at
the same time to enter the image calibration interface, as shown in figure 6-4.
Step 2: Pressing M (13) button to switch the orientation of X-axis ( left-right ) and
Y-axis (up-down);
Step 3：Short press Power (12) button or C (14) button to change the position of
screen and long pressing to start quick shift.
Step 4: After completing calibration, long press M (13) button to save and exit the
calibration interface.
Figure 6-4 Image calibration interface
7. Preventative Maintenance
7.1 Battery Replacement
 The battery power icon is displayed on the upper right side of the interface and
there are four levels of power;
 When the battery icon on the image interface turns red, please change the battery
in time so as not to affect the use;

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
 It is necessary to power off before replacing the batteries;
 Unscrew the battery compartment cover (4) according to the schematic
diagram on the battery compartment cover
 When installing the battery, please place the battery according to the battery
polarity indicator icon in the battery compartment, as shown in figure 7-1.
Figure 7-1 Schematic diagram of battery installation
7.2Product Cleaning and Maintenance
 It is prohibited to clean the product body with the cleaning product which is
corroded or scratched to optical glass.
 The product body can be scrubbed with soft cloth dipping certain amount of
alcohol.
 For optical glass devices such as eyepiece lens and objective lens, dust should
be blown first, and then use charcoal pen or fat-free cotton dipping non-
methylated alcohol to wipe slightly.
7.3 Safety Regulation
▶ Please use batteries regularly. Do not throw the batteries away or put them into
fire after use;
▶ Please use standard charger to prevent the product from damages;

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
▶ No short circuit;
▶ It is prohibited to expose the product in the high temperature environment more
than 60℃；
▶ It is prohibited to put the product into fire.
8. General Trouble Shooting
Table 8.1 Xclip general trouble shooting
Trouble description Probable reason Trouble shooting
Image blurring
The focal length of the
objective lens does not meet;
Adjust the focal length of
objective lens until the image
becomes clear.
No image correction for a long
time. Perform image correction.
Blurred vision Eye relief doesn’t match; Adjust the Eye relief until the
image becomes clear.
No analog video
output
Analog video doesn’t open; Open analog video output.
Data cable doesn’
t support data
transmission. Replace data cable.
Fail to start up
Wrong battery installation or
low power.
Check the battery installation
and battery power.
Insufficient external supply
voltage.
Check the voltage of external
power supply.
The front eyepiece
is stuck during
installation.
Eye relief mounting limit block
isn’t placed parallel to the
guide slot and the position is
dislocation.
Loosen the eyepiece, push it
back to square, and then
rotate the mounting.

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
Reticle wiggle and
cannot aim at the
target.
The
white light sight parameter
is not the correction distance of
100 yards.
Replace the white light sight
with a 100-yard sight.
※ ★Please contact with our company relevant personnel as soon as possible if there
are some abnormalities that cannot be ruled out. Private demolition is strictly prohibited.
9. Appendix
9.1 User Interface Description
 Using custom interface and data cable which supports USB power supply, serial
port and PAL video;
 Supporting USB or battery power and under-voltage or reverse connection
protection.

All rights reserved and shall not be copied and distributed in any form without written permission.
6th Floor of Block A, Changbai Technology Park, No.8 Zhenzhu RD,
Xinzhan General Pilot Zone
China, Anhui, Hefei
，
230012
0551-62829826
9.2 Product Dimensions
9.2.1 Boundary Dimension
9.2.2 Bottom Mounting Hole Size