Infiray Geni series User manual

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

IMPORTANT SAFETY INFORMATION

Environmental influences

Note: Never point the lens of the device directly at intense heat sources

such as the sun or laser equipment. The objective lens and eyepiece can

function as a burning glass and damage the interior components.

Risk of swallowing

Caution: Do not place this device in the hands of small children. Incorrect

handling can cause small parts to come loose which may be swallowed.

Safety instructions for use

-Do not expose the device to fire or high temperatures.

-The battery capacity decreases when operated in a cold ambient

temperature. This is not a fault and occurs for technical reasons.

-Always store the device in its carrying bag in a dry, well-ventilated space.

For prolonged storage, remove the batteries.

-Do not expose your device to extreme temperatures lower than - 20°C

and higher than + 50°C.

-The product shall only be connected to a USB Type C interface.

-If the device has been damaged or the battery is defective, send the

device to our after-sales service for repair.

User information on the disposal of electrical and electronic devices

(private households)

The WEEE symbol on products and/or accompanying

documents indicates that used electrical and electronic

products must not be mixed with ordinary household

waste. For proper treatment, recovery and recycling, take

these products to the appropriate collection points where

they will be accepted without charge. In some countries,

it may also be possible to return these products to your local retailer when you

purchase a corresponding new product. The proper disposal of this product

serves to protect the environment and prevents possible harmful effects on

human beings and their surroundings, which may arise as a result of incorrect

handling of waste.

More detailed information on your nearest collection point is available from

your local authority. In accordance with state legislation, penalties may be

imposed for the improper disposal of this type of waste.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

For business customers within the European Union

Please contact your dealer or supplier regarding the disposal of electrical

and electronic devices. He will provide you with further information.

Information on disposal in other countries outside of the European

Union

This symbol is only applicable in the European Union. Please contact your

local authority or dealer if you wish to dispose of this product and ask for a

disposal option.

Intended use

The device is intended for displaying heat signatures during nature

observation, remote hunting observations and for civil use. This device is not

a toy for children.

Use the device only as described in this instruction manual. The

manufacturer and the dealer accept no liability for damages which arise due

to non-intended or incorrect use.

Function test

-Before use, please ensure that your device has no visible damage.

-Test to see if the device displays a clear, undisturbed image.

-Check that the settings for the thermal imaging camera are correct. See

the notes in the section Observation mode.

Installing/removing the battery

The Geni series thermal imaging scope is equipped with two power supply

systems –one built-in battery pack and one replaceable 26650 battery for

use. The built-in battery pack cannot be removed.

Observation with and without glasses

Thanks to the flexible eyeshade, the Geni series can be used with or without

glasses. It offers a full field of view in both cases.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

1Technical Specifications

Model

GL35

GH35

GL50

GH50

Microbolometer

Type

Uncooled

Resolution, pixels

384×288

640×512

384×288

640×512

Pixel Size, um

12

NETD, mk

≤35

Frame Rate, Hz

50

Optical Characteristics

Objective Lens

F35mm /1.0

F50mm /1.1

Field of View, degrees

7.5×5.7

12.6×9.4

5.3×4.0

8.8×6.6

Magnification, ×

3~12

2~8

4~16

3~12

E-zoom, ×

1 / 2 / 3 / 4

Eye relief, mm

40

48

40

48

Diopter Adjustment, D

-4~+4

Detection Range, m

(Target size: 1.7mx0.5m, P(n)=99%)

1818

2597

Display

Type

AMOLED

Resolution, pixels

1024×768

Size, inch

0.39

Power Supply

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

Battery Type / Capacity

4400mAh Internal battery + 3300mAh Replaceable battery

Max. Operating Time (at t=22℃), h★

10h

External Power Supply

5V (Type C USB)

Operational Characteristics

Max. Recoil Power on Rifled Weapon, m/s²

1000g (g=9.8 m/s2)

Degree of protection, IP code

IP67

Amount of built-in memory, Gb

32

Operating Temperature Range, ℃

-20~+50

Weight, g

＜730g

＜740g

＜780g

Dimension, mm

225x63x90

235x63x90

238x70x90

248x70x90

★ The actual operating time depends on the intensity of using Wi-Fi, video recorder.

➢Improvements may be made to the design and software of this product to enhance its features;

➢If there is any change to the technical specifications of the product, it will be made without prior notice to the customer.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

2Package Contents

● Thermal Imaging Riflescopes

● IRM-030-205-Q1 picatinny mount

● IBP-2 battery pack

● IBC-2 battery charger for battery pack

● Power adapter

● Data cable

● IPB-3 portable bag

● Lens cloth

● A L-shaped wrench

3Description

The thermal imaging riflescope Geni series are designed for the use on

hunting rifles booth in the nighttime and in the daylight in inclement weather

conditions (rain, snow, fog or smog) to see through obstacles hindering

detection of targets (tree branches, tallgrass and shrub etc.). Unlike the

night vision devices, the Geni series do not require an external source of

light and are not affected by strong lights. Geni series can be widely used

in the night hunting, observation and terrain navigation, search and rescue

operations etc.

4Features

●12μm high resolution thermal detector

●High image quality

●Maximum detection range 1818 / 2597m

●4400mAh Internal battery + 3300mAh replaceable battery

●HD AMOLED display:1024*768

●High frame frequency: 50Hz

●Three save sort for rifle types, variable reticle types and color

●Digital Zoom: ×1/×2/×3/×4

●Build-in 32GB storage, supports photographing and video recording

●Build-in Wi-Fi module, support InfiRay Outdoor App

●Build-in digital compass and motion sensor

●Ultraclear mode

●User friendly interface

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

5Components and Controls

1. Eyeshade

2. Eyepiece adjustment ring

3. Type C port

4. Down button / Photography button

5. Menu / M button

6. Up button / Zoom button

7. Power button

8. Side picatinny

9. Lens cover

10. IBP-2 battery pack

11. Lens focus ring/knob

12. Objective lens

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

6Description of Controls

Button

Current Status

Short Press

Long Press

Power Button

Device is off

——

Power on the device

Device is on

Standby the device

Power off

Standby mode

Wake up the device

——

Main menu

Exit to home screen

Power off

Defective pixel calibration

Add / Delete defective pixel

Power off

Up / E-zoom Button

Home screen

Digital Zoom

Turn range notification on/off

Main menu / Quick menu

Navigation upwards

——

Menu Button

Home screen

Enter quick menu

Enter main menu

Quick menu

Switch and confirm parameters

Exit to the upper interface

Main menu

Enter the submenu / Confirm selection

Defective pixel calibration

Confirm selection / Save position

Down/Photography Button

Home screen

Take a Photograph

Start video recording

Main menu / Quick menu

Navigation downwards

——

Video recording

Take a Photograph

Stop and save video

Up + Down Button

Home screen

Calibrate the detector

Background correction

Zeroing interface

——

Freeze the image

Menu + UP Button

Home screen

Turn the PIP function on/off

Turn stadiametric rangefinder on

Up + Menu + Down Button

Home screen

——

Turn reticle function on/off

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

7Battery Pack

Geni series are supplied with a rechargeable Li-ion Battery Pack IBP-2

which allows operation for up to 5 hours. Please Remember to charge the

Battery Pack before first use.

Battery Pack Installation

⚫Turn up the puller (14) on the

battery pack (10), and align the

positioning block (A) of the

battery pack (10) with the groove

(B) of the battery compartment

on the Geni, and push the

battery pack (10) into the battery

slot (13).

⚫When the battery pack is

completely inserted into the

battery slot, turn the puller (14)

clockwise to lock the battery pack.

⚫Close the puller (14), and the battery pack is completely installed.

⚫Geni can only be powered by this battery pack. If other battery packs

are used, it may cause irreparable loss, damage to the device, and can

even possibly cause fire.

Charging with Type-C Port

⚫Install the battery pack into the battery compartment of the product. For

details, see Battery Pack Installation.

⚫Connect the Type C end (18) of the data cable to the Type C port (3) of

the product.

⚫Connect the other end of the data cable to the power adapter (19) that

comes with the product, or connect to another USB power socket with

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

a rated output voltage not exceeding 5V.

⚫Plug the adapter into a 100-240V power socket (20) for charging.

Charging with Battery Charger

⚫Align the positioning block (A) of the battery pack (10) with the groove

(B) of the battery charger (15), and insert the battery pack (10) into the

battery charger (15).

⚫Connect the plug of the USB Type-C cable (18) to the USB connector

of the power adapter (19). Plug the power adapter (19) into a socket

100-240V (20) (110V for US).

⚫Connect the other end of the USB cable (18) to the Type-C port (16) of

the battery charger (15).

⚫After finishing the above steps, the LED indicator (17) on the battery

charger (15) will display the battery charge state.

-◐ Battery level is from 1% to 25%

-● ◐ Battery level is from 25% to 50%

-● ● ◐ Battery level is from 50% to 75%

-● ● ● ◐ Battery level is from 75% to 99%

-● ● ● ● The battery is fully charged.

⚫After the battery is fully charged, remove the battery pack from the

battery charger.

Note: Two batteries can be charged at the same time: the second slot is

designed for it.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

Safety Precautions

⚫Only use the battery charger (15) supplied with the Battery Pack. The

use of any other charger may irreparably damage the Battery Pack or

the charger and may cause fire.

⚫Partial charging the battery is necessary if the battery is planned to be

idled for long time. Avid fully charged or discharged.

⚫Don’t charge the battery instantly while bring the battery from cold

environment to warm environment. Leave 30 to 40 mins before

charging.

⚫Don’t leave battery unattended when charging;

⚫Never use a damaged or modified charger;

⚫Charge the Battery Pack at a temperature from 0℃ to +45℃, otherwise

the battery life will be reduced significantly.

⚫Don’t leave the Battery Pack with a charger connected to the mains

longer than over 24 hours after full charge.

⚫Do not expose the battery pack to high temperature or to a naked

flame.

⚫Do not submerge the battery pack in water.

⚫Don’t connect external device with a current consumption that exceed

permitted levels.

⚫The Battery Pack is short circuit protected. However, any situation that

may cause short-circuiting should be avoided;

⚫Don’t dismantle or deform the Battery Pack.

⚫Don’t hit or drop the battery

⚫The battery capacity may decrease when using the battery in negative

temperature, that is normal, not a defect.

⚫Avoid using the battery at the temperature above the temperature

shown in the table, this may decrease the battery’s life.

⚫Keep the battery out of the reach of children.

8External Power Supply

Geni series support external power supply, such as the mobile power bank

(5V).

➢Connect the external power supply to the USB port (10) on Geni.

➢The riflescope will switch to operation from external power supply, and

the battery will begin slowly charging. The internal battery charges first,

then the external battery

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

➢The display will show the battery icon .

9Operation

Installation of Rifle Mount

➢Before using the Geni series, you need to install the Rifle Mount (21)

on the bottom of your riflescope.

➢The mounting holes (24) in the base of the riflescope enable the Mount

(21) to be installed in one of the multiple positions.

➢The choice of the mounting position helps the user to ensure the

correct eye relief distance depend on the rifle type.

➢Fix the Rifle Mount (21) to the base of the riflescope with a L-shaped

wrench (23) and M5 screws (22) supplied in the package.

➢Install the riflescope on your hunting weapon and make sure that the

chosen position is suitable for you.

➢Remove the riflescope from your weapon.

➢Unscrew the screws one by one, apply some thread sealant onto the

thread of screws and tighten them fully (do not overtighten). Let the

sealant dry for a while.

➢While the sealant is dry, the riflescope is ready to be installed on your

weapon and to be zeroed.

➢After first installation of the riflescope on your weapon. Please follow

instructions in the section 9 “Zeroing”.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

Power On and Image Settings

➢Open the lens cover (9).

➢Press and hold down the Power (7) button to turn on the scope.

➢Rotate eyepiece diopter adjustment ring (2) until images in eyepiece

are clear. After this, there is no need to rotate the eyepiece adjustment

ring (2) for distance or any other conditions.

➢Rotate the lens focus ring (11) to focus on the object being observed.

➢To set up display brightness, image contrast, image modes and digital

zoom, please refer to the Quick Menu Function section.

➢After use, hold down the Power (7) button for about 3 seconds, there

will be prompts of countdown of switch off. Release the button until a

prompt of saving data appears on the screen after counting down from

3 to 0, and the device will switch off after saving data. Please don’t

cut off power supply when saving data, otherwise the data may

not be saved.

10 Zeroing

Geni series feature to use the “Freeze” zeroing method. Zeroing should be

done at the operation temperatures by following the order of these steps:

➢Mount Geni on your weapon according to the instructions of section 8

Installation of Rifle Mount.

➢When using Geni for the first time, press the Up (6) + M (5) + Down (4)

three buttons at the same time for more than 10 seconds to active the

hidden functions about reticle and zeroing functions.

➢Set a target at a certain distance.

➢Adjust the riflescope according to the instructions of section 8 Power on

and image settings.

➢Select the zeroing profile (refer to “Reticle - Zeroing Profile” in Main

Menu).

➢Press and hold down the M (5) button to enter the Main Menu.

➢Briefly press the Up (6) / Down (4) button to select the Zeroing item.

Then press M (5) button to enter the submenu.

➢Base on the preset target distance to select zeroing distance in the

zeroing submenu or add a new distance (refer to Main Menu option

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

Zeroing - submenu Zeroing Distance - Reset Zeroing Distance).

➢After setting the zeroing distance, select the Zeroing option and

briefly press the M (5) button to enter Zeroing interface (see the Main

Menu Option Zeroing - submenu Zeroing Distance - submenu

Zeroing). The X and Y coordinates of the reticle are displayed in the

upper left corner of the screen.

➢Aim and shoot the target.

➢Observe the location of impact. Suppose that the red cross hairs in the

right picture represents the impact point, but the cross is only as a sign

and does not appear on the actual interface.

➢If the impact point does not match the aiming point (the center of the

reticle), keep the reticle center the aiming point, then press and hold

down the UP (6) + Down (4) buttons at the same time until a symbol of

freeze appears on the left of the screen, and the image is frozen.

➢Move the reticle with the Up (6) / Down (4) button until the reticle

matches the point of impact.

➢Briefly press the M (5) button to switch the movement direction between

X (the default direction) and Y. The location of cursor represents the

current selected option, and the icon turns into blue.

➢Press the Up (6) button to move the reticle right or up and the Down (4)

button to move the reticle left or down.

➢When moving the reticle, a white dot appears on the screen,

representing the original position of the reticle.

➢When the reticle moves to the impact point, press and hold the M (5)

button to save the new position of the reticle and exit to the home screen.

➢Take another shot - the point of impact should now match the aiming

point.

11 Calibration

Calibration enables to equalize the detector temperature and eliminate the

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

image defects (such as vertical bars, phantom images, etc.).

There are three calibration modes: Automatic (A), Manual (M) and

Background (B).

Select the required calibration mode in the Main Menu.

➢A mode (Automatic). Device will calibrate automatically according to

the software algorithm. There is no need to close the lens cover (the

internal shutter covers the sensor). Before automatic calibration, there

will be a 5 second countdown prompt behind the shutter icon on the

status bar, that can be to cancelled this calibration during countdown

with a short press of the Power (7) button. In this mode, the riflescope

may be calibrated by user with the Up (6) + Down (4) buttons.

➢M mode (Manual). Press the Up (6) + Down (4) buttons briefly to

activate the shutter calibration without closing the lens cover (the

internal shutter covers the sensor).

➢B mode (Background). Close the lens cover and press Up (6) +

Down (4) buttons briefly. A prompt appears on home screen as “cover

lens during calibration”, background calibration starts after 2s.

12 Digital Zoom

Geni series support to quickly increase the basic magnification by 2 times,

3 times or 4 times, as well as to return to the basic magnification.

➢In the home screen, briefly press the Up (6) button to operate the

incremental digital zoom. in loop to switch magnification times and the

status reveal on the top status bar.

13 Photography and Video Recording

Geni series is equipped with a function for video recording and photography

of the observed image which is saved on the built-in 32GB memory storage.

The photo and video files are named with time, so it is suggested to reset

the date and time in the Main Menu before using the photo and video

functions (refers to Main Menu - Settings - Date/Time Setting in this

manual) or to synchronize date and time in the InfiRay Outdoor application.

Photography

➢Press the Photography (4) button in the home screen to take a photo.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

The image freezes for 0.5 sec with

a camera icon appears on

the upper left corner of screen.

➢Photos are stored in the built-in

storage.

Video Recording

➢In the home screen, press and hold down the Photography (4) button

to start video recording.

➢When the video recording starts, the icon and the video recording

timer displayed in the HH:MM: SS (hour: minute: second) format will

appear on the upper right of the screen.

➢When recording, short press the Photography (4) button to take a photo.

➢Press and hold down

Photography (4) button to stop

and save the video recording.

➢All videos and photos will be

saved in the build-in storage.

Tips:

-You can enter and navigate the menu during video recording.

-Recorded photos and videos are saved in built-in memory card of the

device in the format IMG_HHMMSS_XXX.jpg (for photos) and

VID_HHMMSS_XXX.mp4 (for videos). HHMMSS - Hour/Minute/Second；

XXX - three-digit counter (for videos and photos).

-The counter used for the names of multimedia files can’t be reset.

-If a file is deleted from the list, its number is not taken by the other file.

Caution:

-The maximum duration of a recorded video file is 5 minutes. After this

time expires, the video is recorded to a new file automatically.

-The number of the recorded files is limited by the capacity of the internal

memory.

-Check the available space of the built-in storage card regularly and

move the footage to other storage media to free up the memory card

space.

-Graphic data (status bar, icons and menu) in the recorded video and

photo files are not displayed.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

Memory Access

When the device is turned on and connected to a computer, it is

recognized by the computer as a flash memory card, which is used to

access the device's memory and make copies of pictures and videos.

➢Turn on the riflescope and connect it with the computer via Type-C

cable.

➢Double click “my computer” on the desktop - double click to open the

device named “Infiray” - double click and open the device named

‘Internal Storage’ to access built-in memory.

➢There are different folders named by time in the storage.

➢Recorded photos and videos in that day are saved in the folders

➢Select desired files or folders to copy or delete.

14 Status Bar

The status bar is at the top of the screen and shows information on the

actual operating status of the riflescope, from left to right are:

1. Current image mode ( : White Hot; : Black Hot; : Red Hot;

: Target Highlight; : Pseudo color)

2. Actual zeroing type and distance (such as A100m)

3. Ultraclear mode ( : Ultraclear off; : Ultraclear on)

4. Current magnification (such as 3.0×)

5. Calibration mode (a countdown timer will appear instead of

the calibration mode with 5 seconds remaining until automatic

calibration). The timer will appear only after the microbolometer

temperature has stabilized (after 10 minutes of continuous operation of

the riflescope). Immediately after turning on the riflescope the shutter

calibration activates automatically without displaying the timer.

6. Compass (when it is on)

7. Standby status and time

8. Microphone status ( : Mic is off; : Mic is on)

9. Wi-Fi Status ( : Wi-Fi off; : Wi-Fi on)

10. Clock (set clock in the App “InfiRay Outdoor” or the Main Menu)

11. IBP-2 Battery Pack status

12. Replaceable battery status

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

Icon

Color/Status

Battery Status

Green

more than 40%

Yellow

20% - 40%

Red

Less than 20%, need to charge instantly

Lightning icon

inside

External power supply meanwhile charging

the Battery Pack

USB icon

External power supply without Battery Pack

in the riflescope

15 Quick Menu Function

The basic settings (including image mode, display brightness, image

sharpness and zeroing distance) can be changed in the Quick Menu.

➢In the home screen, short press the M (5) button to enter the Quick

Menu.

➢Switch the function items as described below with a short press of Up

(6) / Down (4) button. The selected items will be highlighted in

background:

⚫Image Mode: short press the M (5) button to switch image modes

among White Hot, Black Hot, Red Hot, Pseudo Color and Target

Highlighting mode.

⚫Display Brightness: short press the M (5) button to change

brightness level from 1 to 5.

⚫Image Sharpness: short press the M (5) button to switch the

image sharpness from 1 to 5.

⚫Zeroing Distance: short press the M (5) button to change default

zeroing distance under the current zeroing profile (if you select the

profile A, you can only switch the distance saved in the profile A).

➢Press and hold down the M (5) button to save modifications and exit

the menu or wait 5 seconds to exit automatically.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

16 Main Menu

➢Enter the main menu with a long press of the M (5) button in home

screen.

➢Briefly press the Up (6) / Down (4) button to toggle between the main

menu options.

➢Main menu navigation is cyclical: as soon as the last menu option of the

first tab is reached, the first menu option of the second tab starts.

➢Adjust the current parameters or enter the submenus with a short

press of the M (5) button.

➢In all menu interfaces, long press the M (5) button to save the

modification and exit to the home screen. And short press the Power

(7) button to return to the previous menu without saving.

➢Automatic exiting from the main menu to the home screen will occur

after 15 seconds of inactivity.

➢Upon exit from the main menu the cursor location is stored only for a

single working session (i.e. until the riflescope is turned off). Upon

restarting the riflescope and entering the menu the cursor will be on

the first menu item.

Main Menu Options and Descriptions

Ultraclear

Turn Ultraclear mode on/off

⚫Press and hold down the M (5) button to enter the Main Menu.

⚫Select the Ultraclear menu option with the Up (6) / Down (4) button.

⚫Turn Ultraclear mode on /off with a short press of M (5) button, along with the sound of shutter calibration.

InfiRay Outdoor • Geni Series• Operating Manual www.infirayoutdoor.com

Wi-Fi

Turn Wi-Fi on/off

⚫Press and hold down the M (5) button to enter the Main Menu.

⚫Select the Wi-Fi menu option with the Up (6) / Down (4) button.

⚫Briefly press of the M (5) button to turn Wi-Fi on /off

Microphone

Turn Microphone on/off

⚫Press and hold down the M (5) button to enter the Main Menu.

⚫Select the Microphone menu option with the Up (6) / Down (4) button.

⚫Briefly press of the M (5) button to turn microphone on/off.

Calibration

Select calibration mode

There are three calibration modes: Automatic(A), Manual (M) and Background (B).

The selected calibration mode is displayed in the status bar (see Status Bar section).

⚫Press and hold down the M (5) button to enter the Main Menu.

⚫Select the Calibration menu option with the Up (6) / Down (4) button.

⚫Briefly press of the M (5) button to enter the submenu.

⚫Press Up (6) / Down (4) button to select one mode from the following modes:

-Automatic. The software determines the need for calibration in automatic mode. The

calibration process starts automatically.

-Manual. The user independently determines the need for calibration based on the quality of the observed image.

-Background. Close the lens cover before starting the calibration.

⚫Briefly press M button to confirm your selection.

InfiRay Geni Series User manual

Popular Thermal Camera manuals by other brands