InFocus LP260 User manual

009-0550-00
QUICK START
video S-video
computer
PC control
audio OUT
computer IN
reset AV
audio
IN
Y ––– Pb ⁄ Cb – Pr ⁄ Cr
It's easy to connect your computer or video player to the
LP260 and start presenting.
Adjust the height or focus of the image. Refer to the for more information.LP260 User's Guide
To connect a computer, plug one end of the VGA cable into the
video connector on your computer and the other end into the Computer In connector
on the projector. If you want sound with your presentation, connect the audio cable.
NOTE: If you are connecting an older Macintosh computer that does not have aVGA 15-pin
connector, you must use Mac adaptors.
Plug the power cord into the projector and into an electrical outlet. Press the Power button
on the keypad or remote to turn the projector on.
Position the projector the desired distance from the screen to get
the desired image size.
If necessary, access the menus by pressing the menu button on the keypad or remote and use
the point buttons to further adjust the image.
5
1
2
4
6
3Turn on your computer or video player.
If you're using a laptop, activate its external video by pressing
the correct activation commands (sometimes the activation
button is labeled with an icon like ).
Audio output
Video audio In
Computer input
4.6’ 7.8’ 20’
2.5’
4.2’
10.4’
to video
output
VGA cable
to AUDIO IN
to audio
output
to COMPUTER
IN
S-video input
lens cap
Computer audio In
Computer mouse input
Composite and
component
video input
qs-eng.fm Page 1 Tuesday, October 10, 2000 3:49 PM
All manuals and user guides at all-guides.com
all-guides.com

QUICK START
Safety Definitions:
•Warning: Statements identify conditions or practices that could result in
permanent personal injury.
•Caution: Statements identify conditions or practices that could result in
damage to your equipment.
Safety Terms:
•Warning: Don’t look directly into the lens when the projector is turned on.
•Warning: Don’t block ventilation openings.
•Warning: To replace the lamp, turn the power off and unplug the
power cord. To avoid burns, wait 45 minutes before opening the
lamp door. Follow all instructions provided in the User’s Guide.
•Warning: Please use the power cord provided. Connect the power
cord to a receptacle with a protective safety (earth) ground terminal.
•Warning: Refer all service to qualified service personnel. Servicing your
own projector will void the warranty. See below for the customer service
contact information.
•Caution: Don’t set liquids on the projector. Spilled liquids may damage your
projector.
•Caution: Don’t place the projector on a hot surface or in direct sunlight.
•Caution: Do not drop the projector. Transport the projector in an InFocus-
approved case; see the Appendix of the User’s Guide for a list of cases.
Safety Symbols:
Attention: For information about usage of a feature, please refer to the
User’s Guide.
Warning: Hot surface. Do not touch.
An arrow pointing to the lamp door of the projector.
Customer Service
If you need assistance, call InFocus Customer Service directly at
1-800-799-9911. Support is free between 6 a.m. and 6 p.m. PST, Monday through
Friday. Support is available in North America after hours and weekends for a fee
at 1-888-592-6800.
Or, send us an e-mail at [e-mail]
In Europe, call InFocus in The Netherlands at (31) 35 6474 010 between 8 a.m.
and 6 p.m. Central European Time. Support is available in Europe after hours and
on weekends for a fee at (31) 35-6474001.
In Singapore, call (65) 332-0659.
SAFETY INSTRUCTIONS:
Please read and follow all safety
instructions provided in this quick
start and your User’s Guide
BEFORE using your new projector.
Failure to comply with safety
instructions may result in fire,
electrical shock, or personal injury
and may damage or impair
protection provided by equipment.
Please save all safety instructions.
qs-eng.fm Page 2 Tuesday, October 10, 2000 3:49 PM
All manuals and user guides at all-guides.com