Ingersoll-Rand ARO LM2350E-B Series User manual

OPERATOR’S MANUAL LM2350E-X-B
RELEASED: 8-14-98
REVISED: 6-11-10
(REV. K)
CHOP-CHECK GREASE PUMP
3” AIR MOTOR
50:1 RATIO
0 - 7500 P.S.I. RANGE
INCLUDE MANUAL: S-633 GENERAL INFORMATION (PN 97999-625)
INCLUDING: SPECIFICATIONS, SERVICE KITS, GENERAL INFORMATION, PARTS, TROUBLESHOOTING
LM2350E-XX-B
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
•Use only genuine ARORreplacement parts to assure compatible
pressure rating and longest service life.
•637227-B Pump Rebuild Kit. Includes the necessary soft parts for
normal service of the entire pump.
SPECIFICATIONS
Model Series LM2350E-XX-B....................
Type Air Operated, Chop-Check.......................
Grease Pump
Ratio 50:1..........................
Air Motor Diameter 3” (7.62 cm)...............
Stroke (Double Acting) 3” (7.62 cm)...........
Air Inlet (female)
LM2350E-X1-B 1/4 - 18 N.P.T.F. - 1...............
LM2350E-X2-B Rc 1/4 (1/4 - 19 BSP Taper)............
Material Outlet (female)
LM2350E-X1-B 3/8 - 18 N.P.T.F. - 1.................
LM2350E-X2-B Rc 3/8 (3/8” - 19 BSP Taper)..............
Pump Construction Carbon Steel...............
Dimensional Data see chart................
Weight see chart.........................
PERFORMANCE
Air Inlet Pressure Range 0 - 150 p.s.i. (0 - 10.3 bar)...........
Fluid Pressure Range 0 - 7500 p.s.i. (0 - 517.2 bar)...........
Cycles / Minute Rec’d @ Working Flow 135.
Displacement In3Per Cycle 0.875.........
Volume / Cycle 0.48 oz. (14.33 ml)...................
Cycles Per Lb. 30...................
Maximum Delivery / Min. 7.5 lbs (3.4 kg)...........
Noise Level @ 100 p.s.i. 85 db(A)*............
Accessories Available 61113 Wall Mount Bracket........
66073-1 Air Line Connection Kit
*The pump sound pressure level has been updated to an Equivalent Continuous Sound
Level (LAeq) to meet the intent of ANSI S1. 13-1971, CAGI-PNEUROP S5.1 using four
microphone locations.
GENERAL DESCRIPTION
Model LM2350E-X-B Series chop-check grease pump is intended to be
used primarily for grease delivery systems. It uses carbon steel and oth-
er materials which make it compatible with most petroleum based lu-
brication products.
NOTE: If this pump was purchased separately (not part of a system),
consult your sales representative for compatible dispensing accesso-
ries which will best match the application. All accessories must be able
to withstand the maximum pressure developed by the pump.
PUMP DATA
Figure 1
Air Inlet (female)
See “Specifications”
MODEL LM2350E-XX-B
Material Outlet (female)
See “Specifications”
MODEL “A” (mm) “B” (mm) WEIGHT (kg)
LM2350E-2X-B 27-3/8” (695) 16-1/4” (412.8) 18.0 lbs (8.16)
LM2350E-3X-B 40-1/8” (1019) 29” (736.6) 22.72 lbs (10.31)
LM2350E-4X-B 48-5/8” (1235) 37-1/2” (952.5) 25.76 lbs (11.68)
LM2350E-6X-B 30-1/8” (765) 19” (482) 19.0 lbs (8.62)
LM2350E-7X-B 38-3/8” (795) 27-1/4” (692) 22.07 lbs (10.01)
LM2350E-8X-B 47-5/8” (1210) 36-1/2” (927) 25.39 lbs (11.52)
NOTE:Dimensions are shown in inches and (mm), supplied for reference only and are typical-
ly rounded up to the nearest 1/16 inch.
2” N.P.S.M. Bung Adapter
(not included with LM2350E-6X-B)
5/16” (8 mm) Thru hole
‘‘B”
‘‘A”
1-1/4”
(31.8 mm)
IMPORTANT
This is one of two documents which support the pump. Replace-
ment copies of these forms are available upon request.
=LM2350E-X-B MODEL OPERATOR’S MANUAL
-S-633GENERALINFORMATIONLUBRICATION PISTONPUMPS
WARNING READ THE GENERAL INFORMATION MANUAL
INCLUDED FOR ADDITIONAL OPERATING AND SAFETY PRE-
CAUTIONS AND OTHER IMPORTANT INFORMATION.
CCN 99762585
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
[phone] FAX[phone] © 2010
www.ingersollrandproducts.com

LM2350E-X-B
Page2of4
PARTS LIST / LM2350E-XX-B
Item Description (size in inches) Qty Part No. [Mtl] Item Description (size in inches) Qty Part No. [Mtl]
1Carriage Bolt (1/4” - 20 x 9” long) (4) 94333 [C]
2Upper Cap (1) 94390 [Z]
n3Track Gasket (2) 94392 [B]
4Sleeve (2) 94316 [Br]
n5“O” Ring (1/16” x 11/16” o.d.) (4) Y325-15 [B]
n6“O” Ring (1/8” x 3/4” o.d.) (4) Y325-206 [B]
7Spool (2) 94310 [D]
n8“U” Cup (1/8” x 3/4” o.d.) (2) Y240-7 [B]
n9“O” Ring (.106” x .587” o.d.) (2) 15066-PM [B]
10 Cylinder (1) 94306 [A]
11 Adapter models LM2350E-X1-B (1) 94384 [C]
models LM2350E-X2-B (1) 94384-1 [C]
n12 “O” Ring (1/16” x 3/4” o.d.) (1) Y325-16 [B]
n13 “O” Ring (1/16” x 7/16” o.d.) (1) Y325-11 [B]
14 Muffler Housing (1) 94443 [A]
15 Foam Liner (2) 94402
16 Edge Trim (2) 94378-1 [N]
18 Retaining Ring (1) 94406 [C]
19 Washer (1) 94515 [C]
n20 “U” Cup (3/16” x 3” o.d.) (2) 94518 [B]
21 Piston (1) 94403 [D]
23 Piston Adapter (1) 94388 [C]
n24 “O” Ring (3/32” x 1” o.d.) (1) Y325-117 [B]
25 Dowel Pin (1/4” o.d. x 7/8” long) (1) Y148-37 [C]
26 Washer (1) 94785 [C]
n27 “O” Ring (3/32” x 11/16” o.d.) (1) Y325-112 [B]
28 Spring (1) 94705 [C]
n29 Rod Seal (1) 93921 [U]
30 Base models LM2350E-X1-B (1) 67188 [C/Z]
models LM2350E-X2-B (1) 67188-1 [C/Z]
31 Nut (1/4” - 20) (4) 93828 [SS]
32 Ground Screw (#10 - 32 x 1/4”) (1) 93005 [C]
n33 Gasket (1) 70834 [Co]
34 Extension Tube
- LM2350E-2X-B (7.531’’) (1) 94401-2 [C]
- LM2350E-3X-B (20.281’’) (1) 94401-3 [C]
- LM2350E-4X-B (28.781’’) (1) 94401-4 [C]
- LM2350E-6X-B (10.281’’) (1) 94401-6 [C]
- LM2350E-7X-B (18.531’’) (1) 94401-7 [C]
- LM2350E-8X-B (27.781’’) (1) 94401-8 [C]
n35 Gasket (1) 70837 [Co]
36 Piston Rod (1) 94385 [C]
37 Pin (1) 94786 [C]
n38 Cotter Pin (1/16” x 1/2” long) (1) Y15-21 [C]
39 Connector - LM2350E-2X-B (3.457”) (1) 94340-2 [C]
- LM2350E-3X-B (16.207”) (1) 94340-3 [C]
- LM2350E-4X-B (24.707”) (1) 94340-4 [C]
- LM2350E-6X-B (6.207”) (1) 94340-6 [C]
- LM2350E-7X-B (14.457”) (1) 94340-7 [C]
- LM2350E-8X-B (27.707”) (1) 94340-8 [C]
Piston & Tube Ass’y (includes 40 - 44) (1) 71523-1
40 Lower Suction Tube (1) [C]
41 Plunger (1) [C]
42 Ball Stop (1) 83276 [C]
43 Ball (9/32” dia.) (1) Y16-209 [C]
44 Adapter (1) 70817-11 [C]
n45 Guide Washer (1) 71524-1 [Co]
46 Spacer (1) 72392-1 [C]
47 Retaining Ring (.763” o.d.) (1) Y147-68 [C]
48 “U” Cup (3/16” x 11/16” o.d.) (1) Y186-4 [B]
49 Guide Spacer (1) 76705 [T]
50 Valve Body (1) 76704 [SH]
nFoot Valve Ass’y (includes 47 - 50) (1) 60940
n51 Gasket (1) F21-65 [Co]
52 Valve Seat (1) 6797 [C]
53 Primer Rod (1) 94446 [C]
n54 Retainer Ring (1) 94397 [C]
55 Primer (1) 94400 [C]
56 Primer Tube (1) 94399 [C]
:57 Bung Assembly (includes 58) (1) 67145-2 [ZA]
:58 Thumb Screw (1/4”-20x1”) (3) Y66-59-C [C]
:Not included with models LM2350E-6X-B
nDarina “EP” 2 Grease Packet (1) 94833
nParts in Repair Kit 637227-B
OPERATING AND SAFETY PRECAUTIONS
WARNING EXCESSIVE INLET PRESSURE. Can cause ex-
plosion resulting in severe injury or death. Do not exceed maxi-
mum operating pressure of 7500 p.s.i. (517.2 bar) at 150 p.s.i.
(10.3 bar) inlet air pressure. Do not run pump without using a
regulator to limit air supply pressure to the pump.
WARNING EXCESSIVE MATERIAL PRESSURE. Can cause
equipment failure resulting in severe injury or property dam-
age. Do not exceed the maximum material pressure of any
component in the system.
Replacement warning label is available upon request, PN \ 94520.
PUMP RATIO X
INLET PRESSURE TO PUMP MOTOR =MAXIMUM PUMP FLUID PRESSURE
Pump ratio is an expression of the relationship between the pump motor area and
the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure is
supplied to the motor of a 50:1 ratio pump it will develop a maximum of 7500 p.s.i.
(517.2 bar) fluid pressure (at no flow) -- as the fluid control is opened, the flow rate
will increase as the motor cycle rate increases to keep up with the demand.
NOTICE: Thermal expansion can occur when the fluid in the materi-
al lines is exposed to elevated temperatures. Example: Material
lines located in a non-insulated roof area can warm due to sunlight.
Install a pressure relief valve in the pumping system.

LM2350E-X-B Page3of4
PARTS LIST / LM2350E-XX-B
16
.TORQUE REQUIREMENTS ,
(11) 80 in. lbs (9 Nm) maximum
(31) 80 in. lbs (9 Nm) minimum
(34, 40, 56) 65 ft lbs (88.1 Nm) minimum
(39) 17 - 25 ft lbs (23.0 - 33.9 Nm)
(44) 50 - 70 ft lbs (67.8 - 94.9 Nm)
(53) 70 - 100 in. lbs (7.9 - 11.3 Nm)
2
3
4
10
7
8
9
9
8
7
6
34 ,
35
40 ,
31 ,
43
21
20
3
47
20
19
18
.11
24
27
41
42
48
36
46
50
52
45
5
33
5
4
15
14
23
29
30
32
54
55
56 ,
49
51
58
57
16
MATERIAL CODE
[A] = Aluminum
[B] = Nitrile
[Br] = Brass
[C] = Carbon Steel
[Co] = Copper
[D] = Acetal
[N] = Neoprene
[SH] = Hard Stainless Steel
[SS] = Stainless Steel
[T] = PTFE
[U] = Polyurethane
[Z] = Zinc
[ZA] = Zinc / Aluminum Alloy
25
37
38
44 ,
26
28
39 ,
53 ,
Figure 2
12
13

LM2350E-X-B
Page4of4
PUMP DISASSEMBLY
NOTE: All threads are right hand. Refer to figure 2 (page 3). Discon-
nect air supply and relieve all system pressure prior to servicing.
Carefully remove the parts, inspect for damage, nicks or excessive wear
and determine if any parts will need replacement.
1. Using a 7/8” wrench, unthread and remove (11) adapter and (12 and
13) ‘‘O” rings, releasing (14) muffler housing.
2. Using a 7/16” wrench, remove (31) nuts.
3. Remove four (1) bolts, (2) upper cap and (3) gasket.
4. Remove (10) cylinder, containing (4) sleeves and (7) spools.
5. Using (1) bolt, push (7) spools and (4) sleeves out “sleeve” end of
(10) cylinder.
6. Remove (18) retaining ring, (19) washer and (21) piston.
7. Remove (25) dowel pin, releasing (23) piston adapter.
8. Remove (3) gasket.
9. Clamp (34) extension tube horizontally in a vise. Unthread and re-
move (30) base, (33) gasket, (28) spring and (26) washer. NOTE:
Remove (29) rod seal only if replacement is necessary.
10. Pull up on (36) piston rod to reveal (38) cotter pin.
11. Remove (38) cotter pin and (37) connecting pin, releasing (36) pis-
ton rod.
12. Using (36) piston rod, push down on (39) connector until it bottoms.
13. Remove (54) retainer ring.
14. Push (55) primer up into (56) primer tube.
15. Lightly wedge a flat blade screwdriver between (55) primer and (56)
primer tube, so (55) primer unthreads with (56) primer tube.
16. Insert a 5/16” diameter rod thru the cross holes in (56) primer tube
and use the rod to unthread and remove (56) primer tube.
17. Remove (46) spacer, (51) gasket and (52) valve seat from (56) prim-
er tube.
18. Remove (47 - 50) foot valve assembly from (53) primer rod.
19. Remove (47) retaining ring, releasing (48) “U” cup. NOTE: Do not
remove (49) guide spacer unless replacement is necessary.
20. Remove (45) guide washer.
21. Clamp (40) lower suction tube horizontally in a vise. Unthread and
remove (34) extension tube and (35) gasket.
22. Using a 7/32” diameter rod in the cross hole in (39) connector and a
9/16” wrench on the flats of (41) plunger, unthread and remove (39)
connector from (41) plunger. NOTE: Do not damage the o.d. of (41)
plunger in any way.
23. Using a 7/16” wrench on flats of (44) adapter and a 1/4” wrench on
flats of (53) primer rod, unthread and remove (53) primer rod.
24. Clamp on flats of (41) plunger and, using a 1/4” wrench on flats of
(44) adapter, unthread and remove (44) adapter, releasing (43) ball
and (42) ball stop.
PUMP REASSEMBLY
NOTE: Thoroughly clean and lubricate all seals and bores with
Shell Darina “EP” 2 upon assembly. Replace all soft parts with new
ones included in the repair kit. Note: Refer to the illustration (figure 2,
page 3) for “U” cup lip seal direction.
1. Assemble (42) ball stop and (43) ball into (41) plunger, securing with
(44) adapter. NOTE: Torque (44) adapter to 50 - 70 ft lbs (67.8 - 94.9
Nm).
2. Assemble (53) primer rod to (44) adapter, using wrenches on flats to
tighten. NOTE: Torque (53) primer rod to 70 - 100 in. lbs (7.9 - 11.3
Nm).
3. Thread (39) connector to (41) plunger, using a 7/32” diameter rod
thru the cross hole to tighten. NOTE: Tighten (39) connector to 17 -
25 ft lbs (23.0 - 33.9 Nm).
4. Assemble (49) guide spacer and (48) “U” cup into (50) valve body,
securing with (47) retaining ring. NOTE: Assemble chamfered cor-
ner of (49) guide spacer into (50) valve body first.
5. Assemble (45) guide washer and (47 - 50) foot valve assembly onto
(53) primer rod.
6. Assemble (46) spacer, (51) gasket and (52) valve seat onto (53)
primer rod.
7. Thread (55) primer onto (53) primer rod, securing with (54) retainer
ring.
8. Thread (56) primer tube to (40) lower suction tube and tighten.
NOTE: Torque (56) primer tube to 65 ft lbs (88.1 Nm).
9. Assemble (36) piston rod to (39) connector, securing with (37) con-
necting pin and (38) cotter pin.
10. Assemble (35) gasket and (34) extension tube to (40) lower suction
tube and tighten. NOTE: Torque (34) extension tube to 65 ft lbs(88.1
Nm).
11. Assemble (27) “O” ring, (29) rod seal, (26) washer, (28) spring and
(33) gasket into (30) base and assemble (30) base to (34) extension
tube. Clamp (30) base horizontally in a vise and tighten (34) exten-
sion tube. NOTE: Torque (34) extension tube to 65 ft lbs (88.1 Nm).
12. Push up on (55) primer, exposing (36) piston rod.
13. Assemble (3) gasket to (30) base.
14. Assemble (24) “O” ring to (23) piston adapter and assemble (23) pis-
ton adapter to (36) piston rod, securing with (25) dowel pin.
15. Replace (20) “U” cups on (21) piston and assemble (21) piston onto
(23) piston adapter, securing with (19) washer and (18) retaining
ring.
16. Replace (5) “O” rings on (4) sleeves and assemble (4) sleeves into
(10) cylinder. NOTE: Assemble each sleeve into the end of the cylin-
der nearest the exhaust hole.
17. Replace (6 and 9) “O” rings and (8) “U” cups on (7) spools and as-
semble (7) spools into (10) cylinder from the opposite end as the (4)
sleeve went in.
18. Assemble (10) cylinder onto the pump, being careful when sliding
over the lips of (20) “U” cups. NOTE: Be sure (3) gasket is seated
properly.
19. Replace (3) gasket on (2) upper cap and assemble (2) upper cap to
(10) cylinder.
20. Assemble (1) bolts to pump, securing with (31) nuts. NOTE: Torque
(31) nuts to 80 in. lbs (9 Nm).
21. Replace (12 and 13) “O” rings on (11) adapter.
22. Assemble (15) foam liners and (16) edge trims to (14) muffler hous-
ing.
23. Assemble (14) muffler housing to (10) cylinder, securing with (11)
adapter. NOTE: Torque (11) adapter to 80 in. lbs (9 Nm).
TROUBLE SHOOTING
If the pump will not cycle or will not deliver material.
•Be certain to check for non-pump problems including kinked, restric-
tive or plugged inlet / outlet hose or dispensing device. Depressurize
the pump system and clean out any obstructions in the inlet/outlet
material lines.
•Check all seals, including track gaskets.
•Check direction of “U” cup lips.
PN 97999-825