Inlite SMART HUB-150 User manual

SMART HUB-150
MANUAL
OUTDOOR LIGHTING

OUTDOOR LIGHTING
2
START SCREEN
WHEN THE IN-LITE APP IS STARTED UP, THE START SCREEN WILL OPEN:
If you do not yet have an account and the transformer is not yet installed, select “I’m
new here”.
If the transformer has already been installed and an account has already been
created, select “I already have an account”. Enter an email address to request your
personal settings code. Enter this code to load the saved settings.
If you want to load the transformer settings shared with another use, select “Use
share code”. This code can be found in the app settings. In the settings, select the
yard for which a share code should be created with the “Share a yard” button. This
code can now be shared
with another in-lite app user.
I’M NEW HERE
If you choose “I’m new here”, the “Start setting your yard” screen will open.
Give the yard a name, such as “Front yard” and press “Next”.
PRESS “SEARCH FOR SMART HUB”
The app will search for a connection to the SMART HUB. Once it has found the
SMART HUB, the SMART HUB number will be shown. See the illustration on the next
page.

OUTDOOR LIGHTING
3
START SCREEN
CONFIRM THE TRANSFORMER
Click on the SMART HUB to identify and configure it.
Check to make sure this is the right SMART HUB.
The blue indicator lighting on the reset button (the
button on the side of the SMART HUB) will start flashing.
To continue, press “Reset button is flashing” once the
right SMART HUB is connected.
A SCREEN WILL NOW OPEN WITH
THE LIGHT ZONES TO BE SET
Press a light zone to set the first light zone.
The screen shown on the right will then open and the
lighting connected
to this light zone will flash a number of times.
Pressing the “Flash again” button will make the
connected lighting in that light zone flash again. Next,
give the light zone a recognizable name and select an
appropriate symbol for the light zone. Repeat these
steps for the two other light zones.
IN THE NEXT SCREEN, PRESS “DONE”
Once all zones have been named,
they will turn green.

OUTDOOR LIGHTING
4
START SCREEN
IF THERE ARE NO OTHER TRANSFORMERS TO SET, YOU CONTINUE BY
PRESSING THE “SAVE SETTINGS” BUTTON.
If there are other transformers that need to be set,
repeat the above steps.
THE FINAL STEP WHEN INSTALLING THE TRANSFORMER IS TO CREATE AN
ACCOUNT FOR SAVING THE SETTINGS.
Enter an email address and press “Save”.
A SCREEN WILL NOW OPEN WITH AN EXPLANATION OF THE APP.
IF DESIRED, PRESS THE “SKIP” BUTTON.
Press the “Continue” button for an explanation of the various options.
Pressing the “Skip” button will cancel the additional explanations.

OUTDOOR LIGHTING
5
ROUTINES
AFTER THE INTRODUCTIONS, THE APP WILL SHOW WHICH ZONES
HAVE BEEN SET AND THE LIGHTING CAN BE
SWITCHED ON AND/OR OFF USING THE APP.
The slider above the word Settings is used to switch o all zones at the same time.
The sliders are used to switch on the lighting in each light zone.
PRESS “ROUTINES” TO OPEN THE “ROUTINES” SCREEN.
In the “Routines” screen, you can add routines for the specific times when the light
zones should be switched on or o automatically. It is also possible to switch the light
zones on or o using a motion detector. This can also be added here as a routine.
Press “Set your first routine”.
ADD A ROUTINE
Here you can set the following routines:
• Sunset automatic: The set zones switch on automatically at sunset and o at the
set time.
• Sunrise automatic:The set zones switch on automatically at a set time and o
again at sunrise.
• SMART MOVE: You can connect a wireless SMART MOVE motion detector to one or
more light zones.
• Sunset adjustable: The set zones switch on and o within a set time period
between 4 pm and 4 am.
• Sunrise adjustable:The set zones switch on and o between 4 am and 10 am.
• Sunrise-sunset:The set zones switch on at sunset and o at sunrise.

OUTDOOR LIGHTING
6
ROUTINE: SUNSET AUTOMATIC AND SUNRISE AUTOMATIC
Give the routine a name and set the start or end time using the slider.
Next, select the light zones for this routine and press the “Add” button.
ROUTINES
SMART MOVE
For a detailed explanation of the SMART MOVE, see
page 13.

OUTDOOR LIGHTING
7
ROUTINE: SUNSET ADJUSTABLE AND SUNRISE ADJUSTABLE
Give the routine a name and set the start and end time using the slider. Next, select
the lines for this routine and press the “Add” button.
ROUTINE: SUNRISE-SUNSET
Give the routine a name. Select the lines for this routine and press the
“Add” button.
ROUTINES

OUTDOOR LIGHTING
8
SETTINGS
This screen is used to manage the various in-lite app settings.
MY YARDS
Select a set yard to change the name of the yard,
transformer or light zone. A transformer or motion
detector can also be added here and/or a share code
generated for sharing parts of the yard with another
smartphone/tablet. If several yards are installed, the
app will also show the names of these yards.
ADD A NEW YARD
“Add a new yard” can be used to add a new yard.
ACCOUNT
In the “Account” section, settings such as the linked
email address can be changed.
Note: The settings will not be lost when logging out.
When you log in again (without resetting the SMART
HUB-150), your settings will be loaded again.
WARRANTY
Here you can find the general warranty conditions for
in-lite products.
MY YARD
This screen shows the SMART HUBs set in the yard and a
new SMART HUB, SMART EXTENDER and/or SMART MOVE
can be added here.
The name of the yard can also be changed and a
share code generated.
Select SMART HUB to view the details of the SMART HUB
and make changes.
Select SMART MOVES to add a new motion detector.
Select “Share yard” to generate a share code for
sharing the yard with another user.

OUTDOOR LIGHTING
9
SETTINGS
ADD A TRANSFORMER
Select the three dots in the top right corner:
• Select “Change name” to change the name of
the yard.
• Select “Remove yard” to remove the yard.
In order to make changes, there must be a connection
to the yard. It is possible, however, to change the
yard name, remove and share the yard without this
connection. (Important: This requires an
Internet connection!)
If you want to change the settings in an inactive yard,
you can switch to a dierent yard. The app will then
search for a connection with the yard. Once the app
has connected to the yard, the settings for this yard can
be changed.
It is still possible, however, to share the yard, change the
name or remove the yard without this connection.

OUTDOOR LIGHTING
10
SETTINGS
SMART HUB
This screen shows all of the SMART HUBs located in the
yard.
Select a SMART HUB to view the details and make
changes. The screen shown on the right shows all the
options.
In this screen, you can change the names of the light
zones and the name of the SMART HUB.
Click on “Light zone name” to change the name of the
light zone and the icon.
The firmware version of the SMART HUB is shown at the
bottom of the screen.
ADD A SMART HUB
Press “Add a SMART HUB” to find a SMART HUB and then
add it. Follow the instructions and give the light zones a
name to add them.

OUTDOOR LIGHTING
11
SHARE A YARD
The share code is used to share all settings configured
with another user. The other user must enter this code
under “Use share code” in the app start screen.
This share code can be easily sent with various apps by
pressing “Share”.
The share code can also be used if a user with an
account adds a yard.
SETTINGS
ADD A YARD
A new yard can be set manually by giving the new yard
a name and continuing with “Next”.
A share code for a yard that is already installed can
also be used. If the share code is used, the new yard will
be added automatically.
I ALREADY HAVE AN ACCOUNT
Enter the email address previously used and press
“Next”.
An email with an access code will be sent to the email
address entered. Use the “Open app email” button to
read the email.
If the code is not accepted, request a new code by
pressing “Send again”.
Aer the correct code is entered, the yard will be
installed automatically in the app and a connection
made to the transformer(s).

OUTDOOR LIGHTING
12
SETTINGS
USE A SHARE CODE
Enter the share code that you received from another
app user. Aer the correct code is entered, the yard will
be installed automatically in the app and a connection
made to the transformer(s).
WARRANTY
Here you can find the general warranty conditions for
in-lite products.

OUTDOOR LIGHTING
13
ADD A SMART MOVE:
A SMART MOVE can be added in two locations in the
app:
a. Settings - My yards - Accessories
SMART MOVE?
b. Routines - SMART MOVE
THE SAME SCREEN IS SHOWN FOR BOTH START
LOCATIONS:
If the SMART MOVE is not found, aer around one
minute, the app will show the second screen once the
red indicator light stops flashing.
Repeat the same steps for connecting the SMART MOVE
by clicking on “Try again”. Hold in the reset button the
SMART MOVE for five seconds and then click again to
restart the installation process.

OUTDOOR LIGHTING
14
SELECT THE LIGHT ZONE(S) TO BE ACTIVATED BY THE
SMART MOVE:
SMART MOVE?
Scroll down to confirm the
settings: “Done”.
! TIP:
If an exclamation point is shown next to a light zone
(per SMART HUB), this means that there is currently no
connection with the transformer. This light zone cannot
be selected and the SMART MOVE settings cannot be
saved and/or changed. Reduce the distance to this
SMART HUB to restore the connection.
Changes can now be saved.
If an update is available for the SMART MOVE, a button
will be shown. Click on “Update” to install the update.

OUTDOOR LIGHTING
15
ADD A SMART EXTENDER:
A SMART EXTENDER can be used to increase the signal
to your phone.
The SMART EXTENDER first needs to be connected to the
power supply. It must then be added to your yard. This
can be done in Settings > Yard > Accessories, where you
will find the Smart Extenders.
In the next screen, click on “Add a Smart Extender”.
The app will then search for the SMART EXTENDER.
SMART EXTENDER
Once the SMART EXTENDER has been found, it must
be configured. You do this by clicking on the SMART
EXTENDER.
Check to make sure this is the right SMART EXTENDER.
The button for the SMART EXTENDER found will start
flashing blue. Click on the “Reset button is flashing” if the
right SMART EXTENDER is flashing.
The SMART EXTENDER has now been added to the yard.
An extra SMART EXTENDER can be added by clicking
on “Add a Smart Extender”. Follow the installation steps
described above.

OUTDOOR LIGHTING
16
GENERAL
GENERAL:
Where can I find the soware version of my
transformer?
Go to Settings – My yards > Select a transformer, such
as Backyard. Scroll down to find the soware version: 32
in this case.
Do the same for the other transformers, such as Front
yard. Every transformer has its own soware, so the
versions may be dierent.
UPDATE A SMART HUB
If an update is available, a button will be shown in the
zone screen. Click on “Update” to install the update.
WHERE CAN I FIND THE VERSION NUMBER OF MY APP?
Go to Settings. Scroll down to find the version number:
1.1.15 in this case.