INNOSILICON T2-BTC User manual

T2-BTC
USER MANUAL
INNOSILICON CONFIDENTIAL

Table of Contents
1. OVERVIEW 1
2. ASSEMBLE THE MINER 2
2.1 Check the miner before power on 2
2.2 Connect the PSU 3
3. OPERATE THE MINER 4
3.1 Enter the miner console 4
3.2 Set up the pool 4
3.3 Check the hashrate of the miner 5
3.4 Network configuration 5
3.5 Other pages 6
3.5.1 Overview 6
3.5.2 Upgrade 6
3.5.3 Modify the password 7
3.5.4 Reboot 7
3.5.5 Factory reset 7
INNOSILICON CONFIDENTIAL
INNOSILICON T2-BTC
INNOSILICON CONFIDENTIAL

1
1. OVERVIEW
INNOSILICON CONFIDENTIAL
T2-BTC
Part Number T2
Algorithm Sha256
Hash Rate 17.2Th/s (±5% )
Power 1430W +10%
Size (L×W×H) 405mm*185mm*165mm
Net Weight 7.2KG (with PSU)
Operating Temperature 0-40 ℃
Network Connection Ethernet
INNOSILICON CONFIDENTIAL

2
2. ASSEMBLE THE MINER
2.1 CHECK THE MINER BEFORE POWER ON
·Check the warranty sticker is well or not, especially the hashboards PSU port side. If the warranty sticker
is damaged when you received the miner, please contact our After-sales.
·Before you power on the miner, shake the miner softly, if you can hear the sound of metal banging on
metal, please contact our After-sales.
·Check if the fan work well, if you find the fans broken please contact our After-sales.
·The cable connection should be same as the follow picture.
Note:
There is a led on each hashboard, which can show the work status of the hashbaord.
When the miner start to work, the led
Solid---workig well
Blink---the hashboard overheat, please check the fans of the miner and the room temp
Off---the hashboard don’t work, please try to reboot the miner or change the data cable. You can contact
our after-sales team if the problem is still exist.
INNOSILICON CONFIDENTIAL
T2-BTC
INNOSILICON CONFIDENTIAL

3
2.2 CONNECT THE PSU
Note: The sequence of the PSU cable should be same with the follow picture。Change the sequence of the
PSU cable will void the warranty.
IP SET button:
Press it 1—4 seconds, it will (1) show the IP of the miner in the “Set IP” tool; (2) change the miner to Static
IP mode and modify the IP to the IP range you set in the “Set IP” tool
Press it 4—15 seconds, the miner will become to DHCP and the settings of the miner should be restore to
default.
Press it more than 20 seconds to switch the Dynamic (Static) IP to Static (Dynamic)
RESET button: Your miner will restart if you press it..
Connect the miner and the router by the Ethernet cable, then the miner can start to run after power on
the miner.
INNOSILICON CONFIDENTIAL
T2-BTC
INNOSILICON CONFIDENTIAL

4
3. OPERATE THE MINER
3.1 ENTER THE MINER CONSOLE
DHCP is the default IP mode of the miner, find the IP via the router or the IP scanner.Enter the IP of the
miner on the browser and press the Enter button. Chrome is the suggested browser. (Please try with
dragonadmin If the password admin is invalid)
INNOSILICON CONFIDENTIAL
T2-BTC
INNOSILICON CONFIDENTIAL
3.2 SET UP THE POOL
Please use the suggested pool as below:
1 ckpool。cn.ckpool.org:443 or pool.ckpool.org:3333
2 slushpool。stratum.slushpool.com:3333
3 f2pool。btc-65536.f2pool.com:3333
4 btc.top。t2.btc.top:8888
or bak.t2.btc.top:3333
5 poolin: stratum+tcp://btc-bj.ss.poolin.com:1800 or
stratum+tcp://btc-sz.ss.poolin.com:1800
6 bitfury: hashrate of the pool maybe low.

5
INNOSILICON CONFIDENTIAL
T2-BTC
3.3 CHECK THE HASHRATE OF THE MINER
After set up the pool, the miner will mine for you.
3.4 NETWORK CONFIGURATION
INNOSILICON CONFIDENTIAL

6
3.5 OTHER PAGES
3.5.1 OVERVIEW
3.5.2 UPGRADE
INNOSILICON CONFIDENTIAL
T2-BTC
INNOSILICON CONFIDENTIAL

7
INNOSILICON CONFIDENTIAL
T2-BTC
3.5.3 MODIFY THE PASSWORD
3.5.4 REBOOT
3.5.5 FACTORY RESET
INNOSILICON CONFIDENTIAL