Innovaid HAPPY REHAB 2 - Small User manual

INSTRUCTIONS FOR USE
HAPPY REHAB 2 – Small
HAPPY REHAB 2 – Medium
HAPPY REHAB 2
–
Large

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 1
TABLE OF CONTENT
PREFACE 3
I. BEFORE USE 4
Included Items 4
Additional Items 5
System Overview 6
Assembly 7
User interface and connections 8
User adjustment 9
rgonomic adjustment 9
II. USING THE HAPPY REHAB 2 SYSTEM 14
Safety 14
PC/ Laptop and external monitor 14
L D Indicators 14
ntering the system 16
xit the system 17
Transportation 17
Foundation Pack 18
III. MAINTANENCE 19
Cleaning the equipment 19
Service and repair 19
Loss of warranty 20
TECHNICAL SPECIFICATIONS 21
Conformity 22
Manufacturer, Distributor/ dealer 22

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 2
WARNING
Read the nstruct ons for use before us ng the
equ pment!
Th s vers on of the nstruct ons for use s val d from
the date pr nted on the front page of t and replaces
any older vers ons of t.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 3
PREFACE
Thank you for choosing the HAPPY R HAB 2 interactive dynamic stand support. For
your safety and to get the most out the system we recommend reading these
Instructions for use carefully.
F g. 1: HAPPY REHAB 2 – w th upper support module and PC.
This instruction for use covers all HAPPY R HAB 2 models printed on the front page
including original accessories described herein.
Details on some illustrations may vary depending model/ size.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 4
I. BEFORE USE
Included Items
Please identify your system components and accessories included in the package
and inspect the contents for any physical damages by visual inspection.
The below listed contents come standard with the HAPPY R HAB 2 system.
ITEM QNT. DESCRIPTION ORDERING
NO.
1
HAPPY R HAB 2 – Small or
HAPPY R HAB 2 – Medium or
HAPPY R HAB 2 – Large
920-002-100
920-002-102
920-002-200
1 Table plate for HAPPY R HAB 2
dynamic stander.
929-200-901
4 Screws for Table plate. 929-210-101
1 Allen key. 5 mm
1 230 V AC POW R ADAPTOR
(Output: 24 V DC, 4.2 A).
929-510-001
1 U mains power cord. 929-610-001
1 USB Magnetic cable, 1.8 m 929-610-002
1 Instructions for use (this user
guide).

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 5
Add t onal Items
Additional items which may be included in the package or ordered separately are
shown in the table below.
Only or g nal accessor es are to be used w th the system.
The above additional items for the HAPPY R HAB 2 system may be
ordered separately from your local dealer.
ITEM DESCRIPTION ORDERING
NO.
C1/C1+/S /M Upper support module
(Only suitable for C1/ S and C1+ / M)
920-000-101
C2 Upper support module
(Only suitable for C2/ L)
920-000-201
FOUNDATION PACK ( nterprise),
Multi lingual
FOUNDATION PACK (Single user),
Multi lingual
920-200-000
920-200-001
Leg/ Knee straps, C1/S and C1+/ M
(Only suitable for C1/ S and C1+/ M)
929-210-010
Leg/ Knee straps, C2/ L
(Only suitable for C2/ L)
929-210-012
Laptop, 10.1"
Laptop, 15.6"
Laptop, 12.1" Touch screen
980-000-002
980-000-001
980-000-003

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 6
System overv ew
The HAPPY R HAB 2 system comprises different components depending on your
configuration. To identify the different components in the system and how to
assemble and interconnect them, please refer to the below illustration and read
the assembly instructions carefully.
F g. 2: System overv ew: HAPPY REHAB 2 system.
Key references (fig. 2):
1 Upper support module – Chest (Additional item).
2 Table plate.
3 Upper support module – Right hip (Additional item).
4 Back support (left).
5 Back support (right).
6 Leg support (right).
7 Transportation wheel (back)
8 Foot platform (right).
9 Transportation wheel (back)
10 Foot platform (left).
11 Transportation wheel (front)
12 lectronic module
13 Leg support (left).
14 Upper support module – Left hip (Additional item).

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 7
Assembly
Before us ng the HAPPY REHAB 2 system the table plate and
Upper support module ( f appl cable) must be mounted onto the
upper frame of HAPPY REHAB 2.
The table plate shall be mounted with the four screws as shown in Fig. 3 below.
nsure the table plate is oriented with the countersunk of the holes upwards as
illustrated.
F g. 3: Mount ng the table plate.
The Upper support module shall be mounted (if applicable) as shown in Fig. 2.
The PC/ Laptop computer may be placed on top of the table.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page
User nterface and connect ons
F g. 4: Connect ons, sw tches and LED nd cators.
For further description see chapter L D Indicators.
Connect the HAPPY R HAB 2 to the mains power supply adaptor via the “DC IN”
connector (B, Fig. 4). Connect the mains power supply adaptor to the mains power
via the power cord. Connect the HAPPY R HAB 2 to the PC/ Laptop computer via
the included Magnetic USB cable (A, Fig. 5) using the “USB” connector (C, Fig. 4)
on the electronic module of the system and a spare USB port on the computer/
laptop. Note the mark (B, Fig. 5) on the Magnetic USB connector must be
orientated upward as shown.
REF. TEXT TYPE DESCRIPTION
A
ON / OFF
Switch
Mains Power Switch
B DC IN Connector 24V DC input
C USB Connector Magnetic USB connector
D - Switch mergency STOP
E FUS Fuse Safety Fuse
F 24V Green 24V power supply
G 5V Green 5V power supply
H OK Green System ready
I RR Red rror
J
STOP
Red
Stop
( mergency stop or power failure)
K R S T Reset Reset internal overload protection
L 0/1 SW A 3.5 mm Jack 0/1 Switch input A (optional)
M 0/1 SW B 3.5 mm Jack 0/1 Switch input B (optional)

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 9
F g. 5: Magnet c USB connector.
Turn on the mains power and switch on the PC/ Laptop computer.
User adjustment
Before us ng the HAPPY REHAB system, the system must be
adjusted to f t the user n all aspects. Th s ncludes both all
the ergonom c aspects as well as the user prof le on the PC/
Laptop computer.
For instructions on how to create a user profile please refer to below section
“Create a User Profile”. These adjustments shall only be carried out by
professionals and certified personnel.
Ergonom c adjustment
The HAPPY R HAB 2 system must fit the user in all the ergonomic aspects. It
should be considered, if the user needs any additional means of support or
adjustments, e.g. an upper support module, additional foot or knee straps or alike.
F g. 6: Adjustment of table he ght.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 10
The height of the table can be adjusted by loosen the two hand wheels (A, Fig 6)
and slide the table up- or downwards, then fasten the two hand wheels (A, Fig 6)
again tightly. Verify the table is in place and the two hand wheels (A, Fig 6) are
properly tightened.
F g. 7: Adjustment of he ght of back support.
The height of the back and hip supports (if applicable) can be adjusted by loosen
the two hand wheels (A, Fig 7) and slide the inner frame up- or downwards, then
fasten the two hand wheels (A, Fig 7) again tightly. Verify the inner frame is in
place and the two hand wheels (A, Fig 7) are properly tightened.
F g. 8: Adjust the pos t on of the back supports.
To adjust the position of the back support (back and forth), loosen the hand wheel
(A, Fig. 8) in each side. The back support can be moved back and forth to fit the
user in a correct upright position. After adjusting the position of the back support,
verify the back support is in place and the according hand wheels (A, Fig. 8) are
properly tightened.
The back support s NOT a seat! The back support may only be
used to support the back of the user n an upr ght pos t on.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 11
F g. 9: Adjustment of he ght of the leg supports.
The height of the leg supports can be adjusted individually by loosen the according
hand wheel (A, Fig. 9) and slide the leg support up or downwards, then fasten the
hand wheel (A, Fig. 9) again tightly. After adjusting the height of the leg support,
verify the leg support is in place and the according hand wheel (A, Fig. 9) is
properly tightened.
F g. 10: Rotat on and hor zontal pos t on of leg supports.
The rotation and horizontal position of the two leg supports -hence the distance
between them- can be adjusted by loosen the according hand wheel (A, Fig. 10).
After adjusting the rotation and position of the leg support, verify the leg support
is in place and the according hand wheel (A, Fig. 10) is properly tightened.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 12
Adjustments of the support cushions (back, hip and chest supports) can be done
as illustrated below in Fig. 11.
F g. 11: Adjust the support cush ons.
To rotate and/ or move the cushion in/ out, use the hand wheels A and B, Fig. 11.
To move the cushions along the bar, use hand wheel B, Fig. 11 only.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 13
F g. 12: Alternat ve or entat on of support cush ons.
If special requirements are needed, the support cushions can be orientated
differently as illustrated above in Fig 12. To do so you’ll need a 2.5 mm Allen key.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 14
II. USING THE HAPPY REHAB 2 SYSTEM
Safety
The HAPPY REHAB 2 s equ pped w th d fferent means to ensure
max mum safety dur ng operat on.
DO NOT ATTEMPT TO DISABLE OR ALTER ANY OF THESE SAFETY
FUNCTIONS!
EMERGENCY SWITCH
The HAPPY R HAB 2 is equipped with an emergency stop switch. To identify the
emergency stop switch, please refer to D, Fig. 4. To activate the emergency stop
switch (D, Fig. 4), press down the red button (D, Fig. 4). This will stop all motors
immediately!
The red “STOP” L D will be lid during an emergency stop.
To release the emergency stop switch (D, Fig. 4), ensure the hazard causing the
activation of the emergency stop has been eliminated, then resetting and reinforce
the motors by turning the emergency stop switch (D, Fig. 4) clock-wise and let it
release in an upward direction from its position.
OVERLOAD PROTECTION
The HAPPY R HAB 2 is equipped with a build-in overload protection of the
actuators (motors). This is to ensure the maximum force exerted by the actuators
(motors) does not exceed the following limits:
HAPPY R HAB 2 - Small / Medium: 100N (approx. 10 kg.)
HAPPY R HAB 2 - Large: 400N (approx. 40 kg).
If any of the actuators (motors) meets a resistance to the movement beyond the
above mentioned limits, the internal overload protection circuit will be activated,
causing all actuators (motors) to stop immediately! The red “STOP” L D will be lid
while the system is in protection mode.
To release the system from the internal protection mode, ensure the hazard
causing the activation of the internal protection mode has been eliminated, then
resetting and reinforce the motors by pressing the “R S T” button on the panel of
the HAPPY R HAB 2.
PC/LAPTOP, EXTERNAL MONITOR
External equ pment such as PC / Laptop computer, external
mon tor must only be powered by batter es. By connect ng these
dev ces d rectly to the ma ns, the HAPPY REHAB 2 system w ll
not conform to the safety regulat ons of EN12182:2002
(electr cal safety for med cal dev ces).

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 15
STABILITY
Before using the HAPPY R HAB 2 system ensure it stands stable on a horizontal
floor. Lock the two transportation wheels at the back by pressing down the lock
into position B “locked” (B, Fig. 32) as illustrated below.
F g. 32: Lock ng the transportat on wheels.
LED Ind cators
The L D indicators are placed on the lower frame of the HAPPY R HAB 2,
illustrated as F – J in Fig. 4). The functions of the five L D indicators (24V, 5V, OK,
RR and STOP) are shown in the table below.
LED SIGNAL DESCRIPTION
24V Solid green 24V power supply is connected
5V Solid green 5V power supply is connected (via USB or
24V)
OK Solid green The system is ready
Slow flashing green The system is resetting
Fast flashing green Setup Mode (when using the Setup Utility)
ERR Solid Red rror. A system error has occurred
STOP Solid Red The actuators has been stopped
The R S T button (K, Fig. 4) is used for resetting the internal overload protection
circuit (see section “Safety” above).

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 16
Enter ng the system
To enter the HAPPY R HAB 2 system open the back support by lifting up the
support and turn it out and backwards as illustrated in Fig. 33. If needed turn the
back support cushion a little backward by loosing hand wheel B in Fig. 11.
F g. 33: Open ng the back supports.
To ease the entrance the heel caps may be detached by lifting them up (hold at
positions A, Fig. 34) and lift upward.
F g. 34: Detach the heal caps.
Place the feet on the foot platforms and close the back supports, mount the heel
caps and tighten the foot straps by pressing them together at the points A, Fig. 35.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 17
F g. 35: T ghten the foot straps.
Ex t ng the system
To get out of the HAPPY R HAB 2 system, loosen the foot straps by pressing the
release button on the buckle and pull the strap (A, Fig. 36) to open. Detach the
heel caps (Fig. 34) and open the back supports as shown in Fig. 33. If needed turn
the back support cushion a little backward by loosing hand wheel B in Fig. 11.
F g. 36: Loosen the foot straps.
Transportat on
The HAPPY R HAB 2 has two transportation wheels hidden under the user panel
and two larger wheels at the back. To unlock the two back wheels lift the brake on
each of the wheels to position A (unlocked) as illustrated in figure 32.
Always lock the transportat on wheels wh le a person s
us ng the system.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 1
Foundat on Pack
For instructions on how to use the Foundation Pack software, we refer to the online
e-user manual.

HAPPY REHAB 2. INSTRUCTIONS FOR USE (EN) Rev. 1.0 Page 19
III. MAINTANENCE
Clean ng the equ pment
The HAPPY R HAB 2 system shall be cleaned on a regular basis depending on the
use of the system, typically between 1- 7 times a week. To clean the device, use a
soft cloth and a little warm water. For disinfection the device methylated spirits
may be used temporary.
Clean ng may only be carr ed out when the dev ce s
d sconnected from the power source (ma ns).
Special caution shall be taken for cleaning the laptop computer and other interface
devices (please refer to their respective instructions for use).
Serv ce and repa r
The HAPPY R HAB 2 system contains no serviceable parts inside. Please refer
servicing to qualified and authorized service personnel.
Refer to the serial number label of the product for product details.
F g. 45: Ser al number label nformat on.
Key references (fig. 45):
A Product type name (common for all similar products).
B Product type ordering number (common for all similar products).
C Manufacturing year.
D AN. Unique barcode for all similar products.
LOT. Production LOT number.
F SN. Unique serial number for this product.
G SN barcode. Unique serial number barcode for this product.
A
B
C
D
E
F
G