Inovus Medical bozzini Hysteroscopy User guide

accessible affordable functional accessible affordable functional

P1.
1| Begin by placing the U-shaped bracket
 onasuitableatsurface.Then,place
the top portion of the small clamp
through the opening at the front of the
 bracket,asillustratedhere.
2| Onceinposition,turnthehandleuntil
 theclampgripsrmlytothe
 bracketandatsurface.
3 |Place the retaining case onto
the U-shaped bracket as shown.

P2.
4| The set-up should now look similar to this
image.
5| You are now ready to place a uterus
model inside the case. Hook the loops of
 themodelontotheinternalxingssothat
it is held securely in place.
6| At this stage you may introduce
 pathologiesintotheuterus,ifyour 
selected model allows you to do so.
Adhesions are inserted by placing the
thread through one of the top holes and
then pulling it through the
corresponding hole below.
 Polypsareinsertedinthesameway, 
however they do not need to be pulled
all the way through the uterus.

7| You are now ready to assemble the
monitor bracket. Begin by removing
the C-clamp from the package.
If your simulator was purchased in a
 hardshellcarrycase,themonitor
bracket will be assembled already and
you may skip to Step 15.
8| Usingthethreeblackboltsprovided,
attach the black post to the
C-clamp.
9| Just so that we know where they are
 forlater,identifythetwoAllenkeys
 alongwiththepushtclampprovided.
Snap this to the post and move to the
 nextstep.
P3.

10 |The swivel arm should be pre-
assembled. Slide this onto the black
 post,thenmovetothenextstep.
11 | Atthedesiredheight,usethelargest
Allen key to lock into position by turning
the bolt in a clockwise direction. Once
 thisstepiscomplete,youmayinsert
the end cap.
P4.
12 | Push the end cap into position.

P5.
14 |Take the screen bracket and screw this
to the back of the monitor using the
bolts provided.
15 | Slide the monitor into position and
screw the bolt into place.
13 | Withthebracketfullyassembled, 
anchor it to your chosen work surface
by turning the handle until it is tight.

P6.
16 | All wiring can be completed using the
numbered stickers attached to the
ends of each adapter. For additional
 support,usethisvisualguide.
Start by plugging in the 12V power
adapter.
17 | Connect the USB splitter to the rear of
the monitor as shown.
18 |Connect the USB to 5V adapter to one
of the USB ports. Connect the female
end of the BNC cable to the male end of
the 5V adapter.

P7.
19 | Connect the female end of the BNC
 extendertothescreen.
20 |Locate the endoscopic camera in the
package. Connect the opposing ends
of the BNC cable to the camera
connectors.
21 | Connect the USBA/B cable to the
remaining USB port on the USB
splitter.

P8.
22 | Now connect this wire to the bozzini
light source.
23 | Pluginthemaleendofthebreoptic
cable into the light source.
24 | Whenthescreenispoweredon,you
should be able to turn the knob on the
front of the light source to activate the
light. Test the light at this stage and
switch off.

P9.
25 |Remove the introducer from the
packaging. Ensure the introducer is
placed inside of the sheath as
 illustratedhere.Inmostcases,this
step will already have been completed
for you.
26 | Rotate the latch in a clockwise
direction to ensure the two
components are securely connected.
27 | You are now ready to insert the
scope into the introducer. Once the
 scopeisfullyinside,ensureitis
locked in place using the latch.

P10.
28 |You may use the apertures in the
U-shaped bracket to hold the assembly
in place as shown here.
29 | Connect the endoscopic camera to the
scope by pinching the two clasps as
shown here.
30 | Attachtheotherendofthebreoptic
cable to the connector on the scope by
 screwingitintoplace.Atthisstage,you
are ready to turn the light source on.

31 | Set-up is now complete and you may
begin operating.
Designed and manufactured by
accessible affordable functional
E: [email protected]
T: [phone]
W: www.inovus.org