Insignia NS-RMTSAM21 User manual

3Point your new remote towards the
TV, then press and hold the
power button.
4 As soon as your TV turns o,
immediately release the power
button. The LED blinks twice.
Note: You have three seconds to release
the power button before your remote
sends a dierent code to your TV.
5Use the power button to turn on
your TV, then test the other buttons.
6If one or more buttons don’t work
as you expect, repeat steps 1
through 5 using the MENU or INFO
button instead of the power
button.
Before using your new product, please read
these instructions to prevent any damage.
QUICK SETUP GUIDE
Replacement
Remote
For Samsung TVs
NS-RMTSAM21
SETTING UP YOUR SOUND BAR OR AUDIO RECEIVER VOLUME CONTROL
If you have your TV connected to a soundbar or audio receiver, you can set up your new remote to control the volume
of this device.
2Enter the rst four-digit code for
your sound bar or audio device.
The LED should blink twice on the
last digit.
3 Test volume + and - button and
the (mute) button.
Note: If the volume buttons don’t
work, start again at step 1 using the
next code on the list.
Turning on all devices
If you have set up your soundbar or
audio device using Simple Setup or
Audio Code Setup, you can now turn
your TV and the audio device both on
and o using a single button. Hold
down the power button for three
seconds. Your new remote turns on
both the TV and the audio device or
soundbar. If you press and release the
button, it only turns on the TV.
Simple Setup
If you have a sound bar or audio device
from one of the brands listed above,
complete the following steps:
1Turn your TV and sound bar or
audio device on, and make sure that
there is something playing that you
can hear.
2On your new remote hold down the
volume + and - buttons together
until the LED blinks twice.
3Point your new remote towards
your sound bar or audio devices
and hold down the digit button for
your brand (see table to the left).
4 As soon as your sound bar or audio
device mutes the volume, release
the digit button. The LED blinks
twice. The remote has found the
code for your soundbar or audio
device.
The volume buttons should now
control the volume of your your
sound bar or audio devices.
Audio code setup
If your sound bar or audio device is
not one of the brands listed, you can
also set up the remote to control it by
entering a four-digit code. Locate the
brand of your sound bar or audio
device in the Remote Codes List found
in the separate document.
1Hold down the volume + and -
buttons together until the LED
blinks twice.
PACKAGE CONTENTS
• Replacement Remote
• Quick Setup Guide
INSTALLING BATTERIES
Insert two AAA batteries (not included)
into the remote. Make sure that the +
and – symbols match the + and –
symbols in the battery compartment.
SETTING UP YOUR REMOTE
The Insignia remote is
pre-programmed to control most
Samsung TVs.
If the buttons do not work, complete
the following steps:
1Make sure that your TV is on and not
in standby mode.
2On your new remote, hold down red
A and blue D until the power
button LED blinks twice.
DIGIT BRAND
0Yamaha
1Bose
2Denon
3Samsung / JBL /
Harman / Kardon
4LG / JVC
5Marantz / Philips
6Onkyo
7Panasonic / Technics
8Pioneer
9Sony
Power
button
AAA
+
AAA
+
LED
LED

3Point your new remote towards the
TV, then press and hold the
power button.
4 As soon as your TV turns o,
immediately release the power
button. The LED blinks twice.
Note: You have three seconds to release
the power button before your remote
sends a dierent code to your TV.
5Use the power button to turn on
your TV, then test the other buttons.
6If one or more buttons don’t work
as you expect, repeat steps 1
through 5 using the MENU or INFO
button instead of the power
button.
Before using your new product, please read
these instructions to prevent any damage.
QUICK SETUP GUIDE
Replacement
Remote
For Samsung TVs
NS-RMTSAM21
SETTING UP YOUR SOUND BAR OR AUDIO RECEIVER VOLUME CONTROL
If you have your TV connected to a soundbar or audio receiver, you can set up your new remote to control the volume
of this device.
2Enter the rst four-digit code for
your sound bar or audio device.
The LED should blink twice on the
last digit.
3 Test volume + and - button and
the (mute) button.
Note: If the volume buttons don’t
work, start again at step 1 using the
next code on the list.
Turning on all devices
If you have set up your soundbar or
audio device using Simple Setup or
Audio Code Setup, you can now turn
your TV and the audio device both on
and o using a single button. Hold
down the power button for three
seconds. Your new remote turns on
both the TV and the audio device or
soundbar. If you press and release the
button, it only turns on the TV.
Simple Setup
If you have a sound bar or audio device
from one of the brands listed above,
complete the following steps:
1Turn your TV and sound bar or
audio device on, and make sure that
there is something playing that you
can hear.
2On your new remote hold down the
volume + and - buttons together
until the LED blinks twice.
3Point your new remote towards
your sound bar or audio devices
and hold down the digit button for
your brand (see table to the left).
4 As soon as your sound bar or audio
device mutes the volume, release
the digit button. The LED blinks
twice. The remote has found the
code for your soundbar or audio
device.
The volume buttons should now
control the volume of your your
sound bar or audio devices.
Audio code setup
If your sound bar or audio device is
not one of the brands listed, you can
also set up the remote to control it by
entering a four-digit code. Locate the
brand of your sound bar or audio
device in the Remote Codes List found
in the separate document.
1Hold down the volume + and -
buttons together until the LED
blinks twice.
PACKAGE CONTENTS
• Replacement Remote
• Quick Setup Guide
INSTALLING BATTERIES
Insert two AAA batteries (not included)
into the remote. Make sure that the +
and – symbols match the + and –
symbols in the battery compartment.
SETTING UP YOUR REMOTE
The Insignia remote is
pre-programmed to control most
Samsung TVs.
If the buttons do not work, complete
the following steps:
1Make sure that your TV is on and not
in standby mode.
2On your new remote, hold down red
A and blue D until the power
button LED blinks twice.
DIGIT BRAND
0Yamaha
1Bose
2Denon
3Samsung / JBL /
Harman / Kardon
4LG / JVC
5Marantz / Philips
6Onkyo
7Panasonic / Technics
8Pioneer
9Sony
Power
button
AAA
+
AAA
+
LED
LED

3Point your new remote towards the
TV, then press and hold the
power button.
4 As soon as your TV turns o,
immediately release the power
button. The LED blinks twice.
Note: You have three seconds to release
the power button before your remote
sends a dierent code to your TV.
5Use the power button to turn on
your TV, then test the other buttons.
6If one or more buttons don’t work
as you expect, repeat steps 1
through 5 using the MENU or INFO
button instead of the power
button.
Before using your new product, please read
these instructions to prevent any damage.
QUICK SETUP GUIDE
Replacement
Remote
For Samsung TVs
NS-RMTSAM21
SETTING UP YOUR SOUND BAR OR AUDIO RECEIVER VOLUME CONTROL
If you have your TV connected to a soundbar or audio receiver, you can set up your new remote to control the volume
of this device.
2Enter the rst four-digit code for
your sound bar or audio device.
The LED should blink twice on the
last digit.
3 Test volume + and - button and
the (mute) button.
Note: If the volume buttons don’t
work, start again at step 1 using the
next code on the list.
Turning on all devices
If you have set up your soundbar or
audio device using Simple Setup or
Audio Code Setup, you can now turn
your TV and the audio device both on
and o using a single button. Hold
down the power button for three
seconds. Your new remote turns on
both the TV and the audio device or
soundbar. If you press and release the
button, it only turns on the TV.
Simple Setup
If you have a sound bar or audio device
from one of the brands listed above,
complete the following steps:
1Turn your TV and sound bar or
audio device on, and make sure that
there is something playing that you
can hear.
2On your new remote hold down the
volume + and - buttons together
until the LED blinks twice.
3Point your new remote towards
your sound bar or audio devices
and hold down the digit button for
your brand (see table to the left).
4 As soon as your sound bar or audio
device mutes the volume, release
the digit button. The LED blinks
twice. The remote has found the
code for your soundbar or audio
device.
The volume buttons should now
control the volume of your your
sound bar or audio devices.
Audio code setup
If your sound bar or audio device is
not one of the brands listed, you can
also set up the remote to control it by
entering a four-digit code. Locate the
brand of your sound bar or audio
device in the Remote Codes List found
in the separate document.
1Hold down the volume + and -
buttons together until the LED
blinks twice.
PACKAGE CONTENTS
• Replacement Remote
• Quick Setup Guide
INSTALLING BATTERIES
Insert two AAA batteries (not included)
into the remote. Make sure that the +
and – symbols match the + and –
symbols in the battery compartment.
SETTING UP YOUR REMOTE
The Insignia remote is
pre-programmed to control most
Samsung TVs.
If the buttons do not work, complete
the following steps:
1Make sure that your TV is on and not
in standby mode.
2On your new remote, hold down red
A and blue D until the power
button LED blinks twice.
DIGIT BRAND
0Yamaha
1Bose
2Denon
3Samsung / JBL /
Harman / Kardon
4LG / JVC
5Marantz / Philips
6Onkyo
7Panasonic / Technics
8Pioneer
9Sony
Power
button
AAA
+
AAA
+
LED
LED

3Point your new remote towards the
TV, then press and hold the
power button.
4 As soon as your TV turns o,
immediately release the power
button. The LED blinks twice.
Note: You have three seconds to release
the power button before your remote
sends a dierent code to your TV.
5Use the power button to turn on
your TV, then test the other buttons.
6If one or more buttons don’t work
as you expect, repeat steps 1
through 5 using the MENU or INFO
button instead of the power
button.
Before using your new product, please read
these instructions to prevent any damage.
QUICK SETUP GUIDE
Replacement
Remote
For Samsung TVs
NS-RMTSAM21
SETTING UP YOUR SOUND BAR OR AUDIO RECEIVER VOLUME CONTROL
If you have your TV connected to a soundbar or audio receiver, you can set up your new remote to control the volume
of this device.
2Enter the rst four-digit code for
your sound bar or audio device.
The LED should blink twice on the
last digit.
3 Test volume + and - button and
the (mute) button.
Note: If the volume buttons don’t
work, start again at step 1 using the
next code on the list.
Turning on all devices
If you have set up your soundbar or
audio device using Simple Setup or
Audio Code Setup, you can now turn
your TV and the audio device both on
and o using a single button. Hold
down the power button for three
seconds. Your new remote turns on
both the TV and the audio device or
soundbar. If you press and release the
button, it only turns on the TV.
Simple Setup
If you have a sound bar or audio device
from one of the brands listed above,
complete the following steps:
1Turn your TV and sound bar or
audio device on, and make sure that
there is something playing that you
can hear.
2On your new remote hold down the
volume + and - buttons together
until the LED blinks twice.
3Point your new remote towards
your sound bar or audio devices
and hold down the digit button for
your brand (see table to the left).
4 As soon as your sound bar or audio
device mutes the volume, release
the digit button. The LED blinks
twice. The remote has found the
code for your soundbar or audio
device.
The volume buttons should now
control the volume of your your
sound bar or audio devices.
Audio code setup
If your sound bar or audio device is
not one of the brands listed, you can
also set up the remote to control it by
entering a four-digit code. Locate the
brand of your sound bar or audio
device in the Remote Codes List found
in the separate document.
1Hold down the volume + and -
buttons together until the LED
blinks twice.
PACKAGE CONTENTS
• Replacement Remote
• Quick Setup Guide
INSTALLING BATTERIES
Insert two AAA batteries (not included)
into the remote. Make sure that the +
and – symbols match the + and –
symbols in the battery compartment.
SETTING UP YOUR REMOTE
The Insignia remote is
pre-programmed to control most
Samsung TVs.
If the buttons do not work, complete
the following steps:
1Make sure that your TV is on and not
in standby mode.
2On your new remote, hold down red
A and blue D until the power
button LED blinks twice.
DIGIT BRAND
0Yamaha
1Bose
2Denon
3Samsung / JBL /
Harman / Kardon
4LG / JVC
5Marantz / Philips
6Onkyo
7Panasonic / Technics
8Pioneer
9Sony
Power
button
AAA
+
AAA
+
LED
LED

V1 ENGLISH 20-0415
RESETTING VOLUME
CONTROL
You can reset the volume control back
to the soundbar or audio receiver.
1 Hold down the green Band
yellow Cbuttons until the LED
blinks twice.
2 Press 977.
3 The LED blinks four times and the
remote is now reset.
LEARNING FUNCTIONS
Your new remote can learn any
function from your original remote.
1Place both remotes on a at
surface with the infrared eyes
facing each other and 1–2 inches
(2.5–5 cm) apart.
Note: If you have diculty with the
learning function, install new
batteries.
2On your new remote, hold down
the green Band yellow Cbuttons
until the LED blinks twice.
3Press 975 on your new remote.
4 On your new remote, press the
button you want to learn a new
function (for example, the volume +
button).
5On the original remote, press the
button with the function you want
to teach to the button you pressed
in Step 4.
If the LED button blinks twice on your
new remote, your new remote learned
the function.
Notes:
• If the LED shows one long blink, the
function was not learned correctly. Try
again from step 4.
• Some remotes send commands
dierently. If you nd a function can’t be
learned, try holding down the button on
the original remote instead of pressing
and releasing.
6Repeat steps 4 and 5 to add another
function to your new remote.
Note: You can learn from multiple
remotes, but only one function per
button.
7After you teach your new remote all
the functions you want it to learn,
press and hold ENTER until the LED
blinks twice.
Note: If you nd one or more buttons
don’t work as you expect, start again at
step 1.
DELETING A LEARNED
FUNCTION
1On your new remote hold down the
green Band yellow Cbuttons until
the LED blinks twice.
2Press 976.
3Press the button on your new
remote you want to reset twice, the
LED should blink twice. The learned
function has been deleted.
ADDING AN APP TO A
SHORTCUT BUTTON
Your new remote has three App
Shortcut buttons which can be used to
immediately open Netix, HBO Now,
Rakuten TV, or Hulu on your Smart TV.
If you don’t have shortcut app buttons,
you can program them to open apps
immediately.
To program the shortcut app buttons,
you need to know the sequence of
buttons you press to bring up the app
(for example, Home > Menu > Down
(twice) > OK).
1Make sure that your TV is on (not in
standby mode) and that the new
remote is operating the TV.
2Hold down an App Shortcut button
until the LED blinks twice.
3Press the sequence of buttons
exactly as you would normally to
open the Streaming Service App.
Note: It might take a few seconds for
the TV to react. Wait for your device to
respond rst. The remote remembers
the timing.
4 After you nish the sequence and
the Streaming Service App starts on
your TV, hold down the App
Shortcut button until the LED blinks
twice and goes o. The shortcut
button is now programmed.
Note: If you nd the sequence doesn’t
work as expected, you can repeat the
same sequence to reprogram.
LEGAL NOTICES
FCC Statement:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
ONE-YEAR LIMITED
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT INSIGNIA:
For customer service, call
1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated
companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
App Shortcut
buttons
Original
remote
New
remote

V1 ENGLISH 20-0415
RESETTING VOLUME
CONTROL
You can reset the volume control back
to the soundbar or audio receiver.
1 Hold down the green Band
yellow Cbuttons until the LED
blinks twice.
2 Press 977.
3 The LED blinks four times and the
remote is now reset.
LEARNING FUNCTIONS
Your new remote can learn any
function from your original remote.
1Place both remotes on a at
surface with the infrared eyes
facing each other and 1–2 inches
(2.5–5 cm) apart.
Note: If you have diculty with the
learning function, install new
batteries.
2On your new remote, hold down
the green Band yellow Cbuttons
until the LED blinks twice.
3Press 975 on your new remote.
4 On your new remote, press the
button you want to learn a new
function (for example, the volume +
button).
5On the original remote, press the
button with the function you want
to teach to the button you pressed
in Step 4.
If the LED button blinks twice on your
new remote, your new remote learned
the function.
Notes:
• If the LED shows one long blink, the
function was not learned correctly. Try
again from step 4.
• Some remotes send commands
dierently. If you nd a function can’t be
learned, try holding down the button on
the original remote instead of pressing
and releasing.
6Repeat steps 4 and 5 to add another
function to your new remote.
Note: You can learn from multiple
remotes, but only one function per
button.
7After you teach your new remote all
the functions you want it to learn,
press and hold ENTER until the LED
blinks twice.
Note: If you nd one or more buttons
don’t work as you expect, start again at
step 1.
DELETING A LEARNED
FUNCTION
1On your new remote hold down the
green Band yellow Cbuttons until
the LED blinks twice.
2Press 976.
3Press the button on your new
remote you want to reset twice, the
LED should blink twice. The learned
function has been deleted.
ADDING AN APP TO A
SHORTCUT BUTTON
Your new remote has three App
Shortcut buttons which can be used to
immediately open Netix, HBO Now,
Rakuten TV, or Hulu on your Smart TV.
If you don’t have shortcut app buttons,
you can program them to open apps
immediately.
To program the shortcut app buttons,
you need to know the sequence of
buttons you press to bring up the app
(for example, Home > Menu > Down
(twice) > OK).
1Make sure that your TV is on (not in
standby mode) and that the new
remote is operating the TV.
2Hold down an App Shortcut button
until the LED blinks twice.
3Press the sequence of buttons
exactly as you would normally to
open the Streaming Service App.
Note: It might take a few seconds for
the TV to react. Wait for your device to
respond rst. The remote remembers
the timing.
4 After you nish the sequence and
the Streaming Service App starts on
your TV, hold down the App
Shortcut button until the LED blinks
twice and goes o. The shortcut
button is now programmed.
Note: If you nd the sequence doesn’t
work as expected, you can repeat the
same sequence to reprogram.
LEGAL NOTICES
FCC Statement:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
ONE-YEAR LIMITED
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT INSIGNIA:
For customer service, call
1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated
companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
App Shortcut
buttons
Original
remote
New
remote

V1 ENGLISH 20-0415
RESETTING VOLUME
CONTROL
You can reset the volume control back
to the soundbar or audio receiver.
1 Hold down the green Band
yellow Cbuttons until the LED
blinks twice.
2 Press 977.
3 The LED blinks four times and the
remote is now reset.
LEARNING FUNCTIONS
Your new remote can learn any
function from your original remote.
1Place both remotes on a at
surface with the infrared eyes
facing each other and 1–2 inches
(2.5–5 cm) apart.
Note: If you have diculty with the
learning function, install new
batteries.
2On your new remote, hold down
the green Band yellow Cbuttons
until the LED blinks twice.
3Press 975 on your new remote.
4 On your new remote, press the
button you want to learn a new
function (for example, the volume +
button).
5On the original remote, press the
button with the function you want
to teach to the button you pressed
in Step 4.
If the LED button blinks twice on your
new remote, your new remote learned
the function.
Notes:
• If the LED shows one long blink, the
function was not learned correctly. Try
again from step 4.
• Some remotes send commands
dierently. If you nd a function can’t be
learned, try holding down the button on
the original remote instead of pressing
and releasing.
6Repeat steps 4 and 5 to add another
function to your new remote.
Note: You can learn from multiple
remotes, but only one function per
button.
7After you teach your new remote all
the functions you want it to learn,
press and hold ENTER until the LED
blinks twice.
Note: If you nd one or more buttons
don’t work as you expect, start again at
step 1.
DELETING A LEARNED
FUNCTION
1On your new remote hold down the
green Band yellow Cbuttons until
the LED blinks twice.
2Press 976.
3Press the button on your new
remote you want to reset twice, the
LED should blink twice. The learned
function has been deleted.
ADDING AN APP TO A
SHORTCUT BUTTON
Your new remote has three App
Shortcut buttons which can be used to
immediately open Netix, HBO Now,
Rakuten TV, or Hulu on your Smart TV.
If you don’t have shortcut app buttons,
you can program them to open apps
immediately.
To program the shortcut app buttons,
you need to know the sequence of
buttons you press to bring up the app
(for example, Home > Menu > Down
(twice) > OK).
1Make sure that your TV is on (not in
standby mode) and that the new
remote is operating the TV.
2Hold down an App Shortcut button
until the LED blinks twice.
3Press the sequence of buttons
exactly as you would normally to
open the Streaming Service App.
Note: It might take a few seconds for
the TV to react. Wait for your device to
respond rst. The remote remembers
the timing.
4 After you nish the sequence and
the Streaming Service App starts on
your TV, hold down the App
Shortcut button until the LED blinks
twice and goes o. The shortcut
button is now programmed.
Note: If you nd the sequence doesn’t
work as expected, you can repeat the
same sequence to reprogram.
LEGAL NOTICES
FCC Statement:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
ONE-YEAR LIMITED
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT INSIGNIA:
For customer service, call
1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated
companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
App Shortcut
buttons
Original
remote
New
remote

V1 ENGLISH 20-0415
RESETTING VOLUME
CONTROL
You can reset the volume control back
to the soundbar or audio receiver.
1 Hold down the green Band
yellow Cbuttons until the LED
blinks twice.
2 Press 977.
3 The LED blinks four times and the
remote is now reset.
LEARNING FUNCTIONS
Your new remote can learn any
function from your original remote.
1Place both remotes on a at
surface with the infrared eyes
facing each other and 1–2 inches
(2.5–5 cm) apart.
Note: If you have diculty with the
learning function, install new
batteries.
2On your new remote, hold down
the green Band yellow Cbuttons
until the LED blinks twice.
3Press 975 on your new remote.
4 On your new remote, press the
button you want to learn a new
function (for example, the volume +
button).
5On the original remote, press the
button with the function you want
to teach to the button you pressed
in Step 4.
If the LED button blinks twice on your
new remote, your new remote learned
the function.
Notes:
• If the LED shows one long blink, the
function was not learned correctly. Try
again from step 4.
• Some remotes send commands
dierently. If you nd a function can’t be
learned, try holding down the button on
the original remote instead of pressing
and releasing.
6Repeat steps 4 and 5 to add another
function to your new remote.
Note: You can learn from multiple
remotes, but only one function per
button.
7After you teach your new remote all
the functions you want it to learn,
press and hold ENTER until the LED
blinks twice.
Note: If you nd one or more buttons
don’t work as you expect, start again at
step 1.
DELETING A LEARNED
FUNCTION
1On your new remote hold down the
green Band yellow Cbuttons until
the LED blinks twice.
2Press 976.
3Press the button on your new
remote you want to reset twice, the
LED should blink twice. The learned
function has been deleted.
ADDING AN APP TO A
SHORTCUT BUTTON
Your new remote has three App
Shortcut buttons which can be used to
immediately open Netix, HBO Now,
Rakuten TV, or Hulu on your Smart TV.
If you don’t have shortcut app buttons,
you can program them to open apps
immediately.
To program the shortcut app buttons,
you need to know the sequence of
buttons you press to bring up the app
(for example, Home > Menu > Down
(twice) > OK).
1Make sure that your TV is on (not in
standby mode) and that the new
remote is operating the TV.
2Hold down an App Shortcut button
until the LED blinks twice.
3Press the sequence of buttons
exactly as you would normally to
open the Streaming Service App.
Note: It might take a few seconds for
the TV to react. Wait for your device to
respond rst. The remote remembers
the timing.
4 After you nish the sequence and
the Streaming Service App starts on
your TV, hold down the App
Shortcut button until the LED blinks
twice and goes o. The shortcut
button is now programmed.
Note: If you nd the sequence doesn’t
work as expected, you can repeat the
same sequence to reprogram.
LEGAL NOTICES
FCC Statement:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
ONE-YEAR LIMITED
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT INSIGNIA:
For customer service, call
1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated
companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
App Shortcut
buttons
Original
remote
New
remote

V1 ENGLISH 20-0415
RESETTING VOLUME
CONTROL
You can reset the volume control back
to the soundbar or audio receiver.
1 Hold down the green Band
yellow Cbuttons until the LED
blinks twice.
2 Press 977.
3 The LED blinks four times and the
remote is now reset.
LEARNING FUNCTIONS
Your new remote can learn any
function from your original remote.
1Place both remotes on a at
surface with the infrared eyes
facing each other and 1–2 inches
(2.5–5 cm) apart.
Note: If you have diculty with the
learning function, install new
batteries.
2On your new remote, hold down
the green Band yellow Cbuttons
until the LED blinks twice.
3Press 975 on your new remote.
4 On your new remote, press the
button you want to learn a new
function (for example, the volume +
button).
5On the original remote, press the
button with the function you want
to teach to the button you pressed
in Step 4.
If the LED button blinks twice on your
new remote, your new remote learned
the function.
Notes:
• If the LED shows one long blink, the
function was not learned correctly. Try
again from step 4.
• Some remotes send commands
dierently. If you nd a function can’t be
learned, try holding down the button on
the original remote instead of pressing
and releasing.
6Repeat steps 4 and 5 to add another
function to your new remote.
Note: You can learn from multiple
remotes, but only one function per
button.
7After you teach your new remote all
the functions you want it to learn,
press and hold ENTER until the LED
blinks twice.
Note: If you nd one or more buttons
don’t work as you expect, start again at
step 1.
DELETING A LEARNED
FUNCTION
1On your new remote hold down the
green Band yellow Cbuttons until
the LED blinks twice.
2Press 976.
3Press the button on your new
remote you want to reset twice, the
LED should blink twice. The learned
function has been deleted.
ADDING AN APP TO A
SHORTCUT BUTTON
Your new remote has three App
Shortcut buttons which can be used to
immediately open Netix, HBO Now,
Rakuten TV, or Hulu on your Smart TV.
If you don’t have shortcut app buttons,
you can program them to open apps
immediately.
To program the shortcut app buttons,
you need to know the sequence of
buttons you press to bring up the app
(for example, Home > Menu > Down
(twice) > OK).
1Make sure that your TV is on (not in
standby mode) and that the new
remote is operating the TV.
2Hold down an App Shortcut button
until the LED blinks twice.
3Press the sequence of buttons
exactly as you would normally to
open the Streaming Service App.
Note: It might take a few seconds for
the TV to react. Wait for your device to
respond rst. The remote remembers
the timing.
4 After you nish the sequence and
the Streaming Service App starts on
your TV, hold down the App
Shortcut button until the LED blinks
twice and goes o. The shortcut
button is now programmed.
Note: If you nd the sequence doesn’t
work as expected, you can repeat the
same sequence to reprogram.
LEGAL NOTICES
FCC Statement:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
ONE-YEAR LIMITED
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT INSIGNIA:
For customer service, call
1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated
companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
App Shortcut
buttons
Original
remote
New
remote

V1 ENGLISH 20-0415
RESETTING VOLUME
CONTROL
You can reset the volume control back
to the soundbar or audio receiver.
1 Hold down the green Band
yellow Cbuttons until the LED
blinks twice.
2 Press 977.
3 The LED blinks four times and the
remote is now reset.
LEARNING FUNCTIONS
Your new remote can learn any
function from your original remote.
1Place both remotes on a at
surface with the infrared eyes
facing each other and 1–2 inches
(2.5–5 cm) apart.
Note: If you have diculty with the
learning function, install new
batteries.
2On your new remote, hold down
the green Band yellow Cbuttons
until the LED blinks twice.
3Press 975 on your new remote.
4 On your new remote, press the
button you want to learn a new
function (for example, the volume +
button).
5On the original remote, press the
button with the function you want
to teach to the button you pressed
in Step 4.
If the LED button blinks twice on your
new remote, your new remote learned
the function.
Notes:
• If the LED shows one long blink, the
function was not learned correctly. Try
again from step 4.
• Some remotes send commands
dierently. If you nd a function can’t be
learned, try holding down the button on
the original remote instead of pressing
and releasing.
6Repeat steps 4 and 5 to add another
function to your new remote.
Note: You can learn from multiple
remotes, but only one function per
button.
7After you teach your new remote all
the functions you want it to learn,
press and hold ENTER until the LED
blinks twice.
Note: If you nd one or more buttons
don’t work as you expect, start again at
step 1.
DELETING A LEARNED
FUNCTION
1On your new remote hold down the
green Band yellow Cbuttons until
the LED blinks twice.
2Press 976.
3Press the button on your new
remote you want to reset twice, the
LED should blink twice. The learned
function has been deleted.
ADDING AN APP TO A
SHORTCUT BUTTON
Your new remote has three App
Shortcut buttons which can be used to
immediately open Netix, HBO Now,
Rakuten TV, or Hulu on your Smart TV.
If you don’t have shortcut app buttons,
you can program them to open apps
immediately.
To program the shortcut app buttons,
you need to know the sequence of
buttons you press to bring up the app
(for example, Home > Menu > Down
(twice) > OK).
1Make sure that your TV is on (not in
standby mode) and that the new
remote is operating the TV.
2Hold down an App Shortcut button
until the LED blinks twice.
3Press the sequence of buttons
exactly as you would normally to
open the Streaming Service App.
Note: It might take a few seconds for
the TV to react. Wait for your device to
respond rst. The remote remembers
the timing.
4 After you nish the sequence and
the Streaming Service App starts on
your TV, hold down the App
Shortcut button until the LED blinks
twice and goes o. The shortcut
button is now programmed.
Note: If you nd the sequence doesn’t
work as expected, you can repeat the
same sequence to reprogram.
LEGAL NOTICES
FCC Statement:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
ONE-YEAR LIMITED
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT INSIGNIA:
For customer service, call
1-877-467-4289 (U.S. and Canada) or
01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated
companies.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
App Shortcut
buttons
Original
remote
New
remote