Insignia NS-HMSB20 User manual

Before using your new product, please read these instructions to prevent any damage.
USER GUIDE
2.0 Channel Mini
Soundbar
NS-HMSB20

www.insigniaproducts.com
2
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting your sound source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting your soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting the AC adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Positioning your soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Back view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Installing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Setting up your soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Choosing your sound source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connecting your soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Connecting the AC power adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Positioning the soundbar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Mounting your soundbar on a wall (optional) . . . . . . . . . . . . . . . . . . . . . . .17
Using your soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Maintaining your soundbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Cleaning your soundbar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Legal notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ONE-YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Introduction
Congratulations on your purchase of an Insignia 2.0 Channel Mini
Soundbar. The soundbar is designed to be used with today’s flat panel
TVs. It features a variety of connections, including Bluetooth, and it can
either be mounted on the wall or placed on a TV stand.
This user guide explains how to correctly install, operate, and get the best
performance from your soundbar. Read this user guide carefully before
installing your system, and then keep it handy for quick reference.

3
2.0 Channel Mini Soundbar
www.insigniaproducts.com
Getting started
To help you get started quickly, here are the basic steps to setting up your
soundbar. For more detailed information, follow the page numbers listed
below:
Connecting your sound source
Choose a sound source, such as a TV, DVD/Blu-ray player, or smartphone
to connect to your soundbar. The device you select will provide the sound
for the soundbar to play. For more detail, see Choosing your sound source
on page 11.
Connecting your soundbar
Connect your sound source to your soundbar. You may need to find or
purchase the correct cable, depending on the connection. For more
detail, see Connecting your soundbar on page 12.
RCA AUX
IN jacks
Digital
Optical jack
USB port
DC in jack
Back of the soundbar

4
NS-HMSB20
www.insigniaproducts.com
Connecting the AC adapter
Plug your soundbar into an AC power outlet. For more detail, see
Connecting the AC power adapter on page 15.
Positioning your soundbar
You can either place the soundbar on a cabinet or mount it on the wall
(optional) under the TV. For more detail, see Mounting your soundbar on
a wall (optional) on page 17.
Important safety instructions
1Read these instructions.
2Keep these instructions.
3Heed all warnings.
4Follow all instructions.
5Do not use this apparatus near water.
6Clean only with a dry cloth.
7Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Back of the soundbar
You can set your
soundbar on a flat
surface or mount
it on a wall.

5
2.0 Channel Mini Soundbar
www.insigniaproducts.com
8Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly
at plugs, outlets, and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or when unused for
long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as when the
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
15 To reduce the risk of fire or electric shock, do not expose this device to
rain, moisture, dripping, or splashing, and no objects filled with
liquids, such as vases, shall be placed on it.
16 An apparatus with a three-prong, grounding-type plug is a Class I
apparatus, which needs to be grounded to prevent possible electric
shock. Make sure that you connect any Class I device to a
grounding-type, three-prong outlet.
17 DO NOT overload wall outlets or extension cords beyond their rated
capacity as this can cause electric shock or fire.
18 The wall plug is the disconnecting device. The plug must remain
readily operable.
19 No naked flame sources, such as lighted candles, should be placed on
the apparatus.
20 The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains, and
similar.
21 Batteries should not be exposed to excessive heat such as sunshine,
fire, or the like.
WARNING: Danger of explosion if the remote control batteries are incorrectly
replaced. Replace only with the same or equivalent type.

6
NS-HMSB20
www.insigniaproducts.com
22 Keep new and used batteries away from children.
23 If the battery compartment does not close securely, stop using the
product and keep it away from children.
24 If you think batteries might have been swallowed or placed inside any
part of the body, seek immediate medical attention.
Placement
• The soundbar cabinet is made out of plastic and is therefore sensitive
to extreme temperatures and humidity. Do not put it in locations
subject to direct sunlight or in humid places, such as near an air
conditioner, humidifier, bathroom, or kitchen.
• Do not put water or other liquids close to the soundbar. If liquid is
spilled on top of the soundbar, it may be damaged.
• The soundbar should be placed on a sturdy, flat surface that is free
from vibration, or mounted on a wall. Do not put the soundbar on an
uneven or unstable surface, where it may fall and cause damage.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage”within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electrical shock to persons.
The exclamation point, within an equilateral triangle, is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.

7
2.0 Channel Mini Soundbar
www.insigniaproducts.com
Package contents
Features
Front view
# ITEM DESCRIPTION
1 Speaker Left and right speakers
2 Status
indicator
Different color LEDs indicate the following:
• Red - Standby mode
• Green - On in digital optical mode
• Yellow - On in AUX IN mode
• Blue - On in Bluetooth mode (blinks while pairing)
• Purple - On in USB mode
3 Remote
control
sensor
Detects signals from the remote control.
Soundbar
Remote Control
AC Power Adapter
RCA Audio Cable
Batteries (2-AAA) Mounting Screws and
Wall Anchors
Mounting Template
3.5 mm to RCA Cable Adapter
User Guide

8
NS-HMSB20
www.insigniaproducts.com
Side view
Back view
# ITEM DESCRIPTION
1 (Power)
button
Press to turn on the soundbar. The status indicator turns green,
yellow, blue, or purple to indicate that the soundbar is on and
what input is selected.
Press again to return the soundbar to standby mode. The status
indicator turns red.
2+(volume up)
button
Press to increase the volume of the soundbar.
3-(volume down)
button
Press to decrease the volume of the soundbar.
4 (sound
source selector)
Press to cycle through the available sound sources. The status
indicator will light:
• Green - Digital optical
• Yellow - AUX IN
•Blue-Bluetooth
•Purple-USB
# ITEM DESCRIPTION
1AUX IN jacks Connect an RCA audio cable (included) to these jacks,
red to red and white to white.
2USB port You can play WAV files from a USB source and charge the
USB device with the 0.5 A connection output.

9
2.0 Channel Mini Soundbar
www.insigniaproducts.com
Remote control
3DIGITAL OPTICAL
jack
If your TV (or other audio source device) has an Optical
OUT jack, connect a digital optical cable (not included)
to your source device and this jack. Make sure that the
sound output from the source is set to PCM format.
4DC IN jack Connect the AC power adapter to this jack to power the
soundbar.
#BUTTON DESCRIPTION
1 (Power) Press to turn on the soundbar. Press again to put the soundbar
into standby mode.
2SOURCE Press repeatedly to cycle through the available sound sources.
3VOL + Press to increase the volume of the soundbar.
4 (previous) In Bluetooth mode, press to skip to the previous track.
5
(play/pause)/
PAIR
• In Bluetooth mode, press to start or pause playback.
• Press and hold this button for three seconds to disconnect
Bluetooth.
6VOL – Press to decrease the volume of the soundbar.
# ITEM DESCRIPTION

10
NS-HMSB20
www.insigniaproducts.com
Using the remote control
Point the remote control directly at the IR sensor on the front of the
soundbar. You must be within approximately 26 ft. (8 m) of the soundbar
and within 30° on either side.
Installing the remote control batteries
1Remove the battery compartment cover from the back of the remote
control.
2Insert two AAA batteries into the battery compartment, making sure
that the polarity on the batteries matches the + and - symbols inside
the battery compartment.
7THEATER Press to enter the THEATER sound mode to optimize music played
in a theater setting. The status indicator on the soundbar blinks
white three times.
8STANDARD Press to enter the STANDARD sound mode to optimize general
music. The status indicator on the soundbar blinks white three
times.
9 (Mute) Press to mute the sound from the soundbar. Press again to restore
the sound.
10 (next) In Bluetooth mode, press to go to the next track.
11 NEWS Press to enter the NEWS sound mode to optimize the spoken
voice. The status indicator on the soundbar blinks white three
times.
#BUTTON DESCRIPTION
IR Sensor

11
2.0 Channel Mini Soundbar
www.insigniaproducts.com
3Replace the battery compartment cover.
Setting up your soundbar
Choosing your sound source
• Look at your sound source device, such as a TV, DVD/Blu-ray player, or
cable box, to identify your audio OUT ports. Choose one connection
option below that fits your sound source. You can connect several
devices and switch the sound source as required.
You can also choose a USB thumbdrive or Bluetooth device as your sound
source. See USB sound source on page 13, or Bluetooth sound source on
page 14.
CAUTIONS:
• Do not spill water or any liquid on the remote control.
• Do not place the remote control on a wet surface.
• Do not place the remote control in direct sunlight or near sources of
excessive heat.
• If the remote control is not going to be used for a long time, remove the
batteries to avoid any damage that may be caused by leakage and
corrosion.
CAUTIONS:
• Turn off or unplug all devices while you are making connections.
• If you mounted your soundbar on a wall, you must use right-angle cable
connectors for the RCA cable (AUX IN) connection.
AUDIO
QUALITY
JACK
TYPE CABLE
Best Digital Optical cable (not included). See Digital
Optical connection (best) on page 12.
Good RCA audio cable (included). See RCA
connection (good) on page 12.
Good 3.5 mm to RCA audio cable adapter (included).
See RCA connection (good) on page 12.

12
NS-HMSB20
www.insigniaproducts.com
Connecting your soundbar
Digital Optical connection (best)
1Connect one end of the digital optical cable (not included) to your
soundbar.
2Connect the other end into the Digital Optical Output port on your
source device.
3Change the device’s audio output to 'PCM' format (typically found in
audio settings). Refer to the documentation that came with your
sound source for more information.
4Go to Connecting the AC power adapter on page15.
5After your soundbar is plugged in and turned on, press the SOURCE
button repeatedly on your soundbar or remote control until the
source indicator turns green.
RCA connection (good)
1Plug the red and white RCA connectors on the RCA audio cable
(included) to the AUX IN jacks on your soundbar, red to red and white
to white.
Important: Make sure that the device you connect and select as your sound
source is outputting sound to the soundbar. See your device's user manual for
more information.
Digital optical cable
(not included)
Back of the soundbar
Audio source (TV, Blu-ray
player, or cable box)

13
2.0 Channel Mini Soundbar
www.insigniaproducts.com
2Connect the other end of the RCA audio cable into the Audio Output
ports on your sound source.
3Go to Connecting the AC power adapter on page15.
4After your soundbar is plugged in and turned on, press the SOURCE
button repeatedly on your soundbar or remote control until the
source indicator turns yellow.
USB sound source
1Plug a USB thumbdrive (with WAV files) into the USB port on the back
of your soundbar.
2Go to Connecting the AC power adapter on page15.
3After your soundbar is plugged in and turned on, press the SOURCE
button repeatedly on your soundbar or remote control until the
source indicator turns purple.
Note: If your sound source does not have RCA audio output jacks (for example a
smartphone, tablet, or iPad), use the included 3.5 mm to RCA cable adapter.
Important: Make sure that the device you connect and select as your sound
source is outputting sound to the soundbar. See your device's user manual for
more information.
Note: If you mount your soundbar on a wall, you will not be able to use a USB
thumbdrive as a sound source.
RCA cable (included)
Audio source (TV, Blu-ray
player, or cable box)
Back of the soundbar
OR
RCA cable (included)
3.5 mm to RCA cable
adapter (included)
Audio source with 3.5 mm
jack (smartphone, tablet,
iPad)

14
NS-HMSB20
www.insigniaproducts.com
4Control USB playback by pressing the (play/pause) PAIR,
(previous), and (next) buttons on the remote control.
Bluetooth sound source
Before you can use your soundbar with a Bluetooth device, you need to
pair your device to the soundbar. Go to Connecting the AC power adapter
on page 15. After your soundbar is plugged in and turned on, do the
following:
Pairing your devices
1Select Bluetooth as the input source by pressing the SOURCE button
on the soundbar or on the remote control. The status indicator blinks
blue.
2Navigate to your device's Bluetooth settings, turn on Bluetooth, then
search for available devices. For additional information on pairing
your device, see your device’s documentation.
3On your Bluetooth device, select “NS-HMSB20” from the device list.
Repeat steps 1-2 if “NS-HMSB20” is not displayed.
4If a PIN code is requested, enter “0000.”
5When the Bluetooth connection has been established, the status
indicator turns solid blue.
Disconnecting your devices
• Turn off the Bluetooth function on your device.
Note: If playback does not begin immediately, press the (play/pause)/
PAIR button on the remote control.
Notes:
• Your soundbar must be on to make a Bluetooth connection.
• Place the Bluetooth device within 33 ft. (10 m) of your soundbar.
Notes:
• Some devices, such as an iPhone, connect immediately after pairing so the
status indicator on your soundbar remains on. Other devices, such as
notebook computers, may ask you if you wish to connect. In this instance,
the status indicator continues to blink until a connection is established.
• Your soundbar saves pairing information for up to eight devices. However,
it can only be connected and play content from one device at a time.
• When you turn on your soundbar, it automatically connects to the last
connected device if that device is in range. To connect to a different paired
device, turn off Bluetooth or unpair from the currently paired device and
manually connect to the other paired device.
Important: Make sure that the device you connect and select as your sound
source is outputting sound to the soundbar. See your device's user manual for
more information.

15
2.0 Channel Mini Soundbar
www.insigniaproducts.com
Reconnecting to a paired device
When your soundbar is not paired to a device, the LED indicator blinks.
Connecting to a different device
1On your Bluetooth device you are currently connected to, turn off the
Bluetooth function or unpair the soundbar in your Bluetooth device
list. The soundbar can now be connected to another Bluetooth
device.
2Follow the section Positioning the soundbar on page 16 to connect a
new device.
Receiving a phone call while playing music
• When you receive a call while playing music through your phone, the
music stops automatically.
• When you hang up, depending on the setting of your phone, the
current track may resume playback.
Connecting the AC power adapter
After you have connected your soundbar to an audio source, you need to
connect the AC adapter and plug it in.
1Connect the AC power adapter to the DC IN jack on the back of the
soundbar.
Your soundbar loses the Bluetooth
connection if you…
To reconnect...
Turn it off. Turn on your soundbar. Your soundbar
searches for the last connected Bluetooth
device and reconnects.
Move the Bluetooth device out of range. Move your Bluetooth device within 33 ft.
(10 m) of your soundbar.
Turn off your Bluetooth device. Turn on your Bluetooth device, then make
sure that Bluetooth is on.
Turn off Bluetooth on your Bluetooth
device.
Turn on Bluetooth on your Bluetooth
device.
Connect your Bluetooth device to
another Bluetooth device.
Disconnect your Bluetooth device from the
other Bluetooth device, then set your
device to pairing mode. Select
“NS-HMSB20” on your Bluetooth device.
Note: If a device does not automatically reconnect, you may need to reselect
“NS-HMSB20” on your Bluetooth device.
CAUTION: Make sure that the electrical outlet matches the input requirements
of 100-240 V, 50/60 Hz before connecting.

16
NS-HMSB20
www.insigniaproducts.com
2Plug the other end of the AC power adapter into a power outlet or
surge protector.
Positioning the soundbar
• You can set the soundbar on a flat surface or mount it on a wall.
WARNING: Improper installation can result in serious injury or damage to your
soundbar. If necessary, seek the assistance of a professional.
Note: If you are installing screws into drywall or concrete, use wall anchors
(provided) designed for that type of surface.
Back of the soundbar
OR

17
2.0 Channel Mini Soundbar
www.insigniaproducts.com
Mounting your soundbar on a wall (optional)
You will need (not included with your soundbar):
1Select a location close to your TV and directly in front of the
viewing/listening position. For best sound quality, choose a location
where sound waves are not blocked by furniture or other obstacles.
2If you are mounting your soundbar to drywall, use the stud finder to
find the studs and mark the locations.
3Drill two 15/64” holes into the wall 11.4" (29 cm) apart and make sure
they are level.
Notes:
• Make all connections to your soundbar before mounting the soundbar on a
wall.
• If you mount your soundbar on a wall, you will not be able to use a USB
thumbdrive as a sound source.
• If you mount your soundbar on a wall, you must use right-angle cable
connectors for the RCA cable (AUX IN) connection.
Level Stud finder
(optional for wood
stud installation)
Drill and
drill bit Hammer Screwdriver
Tape measure Tape Screws (2) - 9/16”(3.6 mm) self-tapping, at
least 1 1/8”(28.5 mm) long
Wall anchors (2)
11.4”(29 cm)

18
NS-HMSB20
www.insigniaproducts.com
4If you are mounting on drywall without studs or on concrete, install
wall anchors (included) into the holes you drilled.
5Secure two screws (included) to the wall or wall anchors (if required).
The screws must protrude from the wall by about 5/32" (4 mm). Use a
9/16” (3.6 mm) self-tapping wood screw (or similar), 1-1/8" (28.5 mm)
in length. The screw head must be approximately 9/32" (7 mm).
6Align the speaker hanging brackets with the screws, then hang the
soundbar on the screws.
WARNING: Improper installation can result in serious injury or damage to your
soundbar. If necessary, seek the assistance of a professional.
Approx.
5/32"
(4 mm)
Wall
11.4" (29 cm)

19
2.0 Channel Mini Soundbar
www.insigniaproducts.com
Using your soundbar
This system lets you access four different sound sources, including
Optical, AUX IN (RCA), Bluetooth, and USB.
Listening to your soundbar
1Press the (Power) button to turn on your soundbar. The power
indicator turns off.
2Turn on the audio source device connected to your soundbar and
begin playback.
3Press the button on the soundbar repeatedly to select the audio
source or press the selected source button on the remote control
until you hear sound from your soundbar.
4Adjust the volume on your soundbar or the source audio device to a
comfortable level.
5Press the (Power) button again to turn off your soundbar. The
status indicator lights red.
Maintaining your soundbar
Cleaning your soundbar
Notes:
• If you use the OPTICAL connection, you must change your device’s audio
output setting to “PCM” format. Refer to the manual you received with the
output device for additional information.
• Make sure that your sound source is set to output sound to the soundbar
(whichever connection method you choose). Refer to your device’s manual
for additional information.
WARNING: Continuous use of high volume sound may permanently damage
your hearing.
CAUTION: Only use a soft and clean rag to clean the outside of the soundbar.
Never clean it with chemicals, detergents, or abrasives.

20
NS-HMSB20
www.insigniaproducts.com
Troubleshooting
Check this list for a possible troubleshooting solution before calling for
service.
PROBLEM POSSIBLE SOLUTIONS
The power does not
come on.
• Make sure that the AC power adapter is securely plugged
into the power outlet and the soundbar.
• Make sure that the soundbar is turned on. It does not turn
on automatically when you turn on your TV or other
sound source.
The remote control
does not work.
• Remove any obstacles between the remote control and
the IR sensor on the soundbar.
• The remote control batteries may be exhausted, replace
them.
• Move closer to the soundbar. The remote control is only
effective to approximately 26 ft. (8 m) of the soundbar
and within 30° on either side.
The sound is breaking
up or buzzing.
• Make sure that you are connected to an audio OUT jack
on your sound source. The port will not send audio out if
it is an INPUT jack.
• Make sure that all connections are secure and cables are
not broken or damaged.
• If you are using the OPTICAL connection, make sure that
the source device’s audio source is set to “PCM” format.
Refer to the documentation you received with the audio
source device (such as a TV or DVD/Blu-ray player) for
additional information.
• Connect to a different source device (such as a TV or
DVD/Blu-ray player) to see if the buzzing still occurs. If it
does not, this may indicate an issue with the original
source device.
• Use a different connection method (for example, try
Optical instead of AUX IN) between the soundbar and the
source device to make sure that the jacks on both devices
are still working.
• Make sure that the audio cable you are using is not
damaged or broken. Try using another one.
I can hear sound from
both my TV and my
soundbar.
• Turn off or mute the internal speakers of your TV. Refer to
the TV’s manual for instructions.
My TV remote does
not control my
soundbar.
• Universal remotes will only control your soundbar’s
volume. Use the controls on your soundbar or the remote
that came with it to change the soundbar’s audio source
or sound mode.
• Make sure that you aim your universal remote at the
remote sensor on the front of your soundbar.
• Make sure that you select the correct source on your
universal remote.