InSinkErator Water Dispenser User manual

instant hot water dispenser
filter system
owner’s
manual
manuel d’utilisateur
manual del usuario
système de filtre
sistema de filtro
43386 Filter Owner's Manual.qxd 9/26/02 11:58 AM Page 2 Greg Leber Jobs:39237 ISE HWD Owner's Manual:43386 HWD Filter

With all of the components secured in place,
the tubing connections can be made. When
routing the tubing between components,
several guidelines should be observed:
•Tubing runs should generally follow the
contour of the cabinet rather than interfere
with the cabinet storage area.
•Arrange the tubing so that there are no
sharp bends. Leave some extra length in the tubing for ease of servicing,
then cut tubing to the desired length.
•Insert tubes completely into all quick-connect fittings to the stop
(minimum depth of 1/2"). Completely insert 3/8" polyethylene tubing
into inlet and outlet sides of the filter head.
•The polyethylene tubes can be cut, but caution should be exercised to
ensure that a clean (burr-free) cut is made, perpendicular to the tube.
1. Mount the Head & Filter Bracket
Install the head and bracket assembly so that all
plumbing connections can be made without
stretching, kinking, or pinching the 3/8" polyethylene
tubes.The tubes can be cut to make installation
easier.Make sure the mounting location allows for
the filter cartridge to be removed and replaced.
The filter system is equipped with a vent line that
opens when the filter cartridge is removed. Under
normal conditions,approximately 2 ounces (~60 cc)
of water is discharged from the vent. To conveniently redirect this discharge, a 6”section of gray
tubing is provided. If you wish to install, simply slide one end of the gray tube over the vent and
the other end into the hole on the head & bracket assembly.
With a pencil, mark the mounting hole locations. Pre-drilling pilot holes (1/8
" dia.) may be
required.
Attach the mounting bracket using the screws provided.
Note: Do not locate the filter directly above an electrical outlet or other electrical components.
Installing the In-Sink-Erator Filter System
2. Connect Filter into Filter Bracket
Remove the cap from cartridge. Inspect the
cartridge for any damage. Make sure the O-
rings are present and positioned correctly in
the grooves. Moisten the O-rings with water.
Do not use petroleum products to lubricate
the O-rings. Insert the filter cartridge into the
head & bracket assembly.
Align the“IN/OUT” mark on the filter cartridge with the mark on the
head & bracket assembly and rotate until the“LOCK” mark on the filter
aligns with the mark on the head & bracket assembly (approx.90˚).
Note: If the O-ring is breached, water will leak from the head and bracket
assembly.To remedy, remove the filter cartridge, inspect O-ring and
reinstall.
3. Make Plumbing Connections
43386 Filter Owner's Manual.qxd 9/26/02 11:58 AM Page 3 Greg Leber Jobs:39237 ISE HWD Owner's Manual:43386 HWD Filter

Completely insert 3/8" polyethylene tubing from the outlet side of filter head into the 3/8" to
1/4" divider ("Y" quick-connect fitting).This divider allows the system to supply one or two
plumbing fixtures with filtered water.
To connect one plumbing fixture:
Completely insert the plumbing fixture's 1/4" copper tubing into one of the outlets of the "Y"
fitting. In the other outlet of the "Y" fitting, insert the provided plug.
To connect two plumbing fixtures:
Completely insert both plumbing fixture's 1/4" copper tubes into both outlets of the "Y" fitting.
Discard the provided plug.
To remove a tube from its quick-connect fitting, depress the release ring
into the fitting and gently pull the tube away from the fitting.
3. Make Plumbing Connections ( continued)
4. Connect to Cold Water Supply Line
Supplied with the unit is a brass nut, ferrule and tube insert to
connect the polyethylene tube from the input side of the filter
to a standard 3/8" compression fitting. Other plumbing
connections are possible – check with a qualified plumber
should you have questions.
Slide the nut and ferrule over the tube and then push in the
tube insert. Insert the tube into a standard 3/8" compression
fitting (not supplied) and tighten. Be careful not to overtighten.
Note:Connect the filter to the cold water supply only.
5. Test the Water Connection
Test the water connection to see if it is watertight. If it is not, relieve water pressure by
turning off the water supply, and adjust or tighten fittings as necessary.
43386 Filter Owner's Manual.qxd 9/26/02 11:58 AM Page 6 Greg Leber Jobs:39237 ISE HWD Owner's Manual:43386 HWD Filter

F201 Chemical & Mechanical Reduction Filter Specifications:
(Use replacement cartridge F-201R) This cartridge (included with the system) provides
mechanical and chemical reduction of dirt/rust, taste/odor, chlorine and particulates.
Pressure: 30-125 psi
Temperature: 33˚F–100˚F
Flow Rate: 0.75 gpm
Capacity: 500 gallons
Filter Capacity: 500 gallons, depending on local water conditions.Note that while the testing was
performed under standard laboratory conditions,actual performance may vary.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system.For cold water use only.Systems must be installed and
operated in accordance with the Manufacturer’s recommended procedures and guidelines.See
warranty card for warranty.For service and parts, contact your local dealer or In-Sink-Erator directly at
1-800-558-5700.
Application guidelines/Water Supply Parameters for NSF Testing: Service flow of 0.75 gpm, community or
private well water supply, water pressure of 30-125 psi, water temperature of 33˚F–100˚F . Except as noted,
all testing performed at pH = 7.5±0.5, Flow: 0.75 gpm, Pressure: 60 psi, Temp:20˚±3˚C.
Contact an authorized In-Sink-Erator service agent for repairs or replacement components.
System is tested and certified by NSF International
against ANSI/NSF Standard 42 for the reduction of
Particulate Class I, Chlorine Class I, Taste and Odor.
Full 1 Year Warranty: Covers all replacement parts and repair labor to correct defects in
material or workmanship in the filter system, excluding the replaceable filter cartridge,for the
full warranty period from the date of installation in your home. If warranty service is required
during the warranty period, contact an authorized In-Sink-Erator service agent to replace or
repair the unit in your home at no cost to you.
This warranty gives you specific legal rights and you may also have other rights which vary. If
the manufacturer determines that the unit should be replaced rather than repaired, the
warranty on the replacement unit will be limited to the unexpired term of the original
warranty. No other expressed warranty, written or oral, applies.
Warranty is determined by the serial number of the unit installed and the date of installation. A
purchase or installation receipt may be required to verify warranty status.The foregoing
warranty does not apply to damage or inoperation resulting from accident, alteration, misuse,
abuse, improper installation, any installation not in accordance with these instructions, or
installations not in accordance with local plumbing codes.We do not assume any
consequential damage.Warranty will be voided if installed in a commercial or industrial
situation.
If you have questions concerning your unit or when service is needed, please call for the name
of the nearest authorized service center.
If Your Unit Does Not Operate, contact your authorized service center or In-Sink-Erator.
When writing or calling, give the following information: date, your name, address and phone
number. Describe the product by model number, serial number, date purchased, place
purchased, service history (include name and address of service agent) and clearly describe the
problem and service required.
Warranty Information
Contaminant Average Product Average USEPA NSF
Reduction Influent ppm Water ppm Reduction Recommendation Test
Taste/Odor/ 2.10 0.05 97% N/A 500180-00
Chlorine
Particulates 286667 1683 99% N/A 500181-00
43386 Filter Owner's Manual.qxd 9/26/02 11:58 AM Page 7 Greg Leber Jobs:39237 ISE HWD Owner's Manual:43386 HWD Filter

F-201R
for reduced chlorine
taste and odor
...replace every
3 months
F-501R
for better tasting
and healthier water
...replace every
6 months
REMEMBER!
Replace your filter
regularly with only
genuine In-Sink-Erator®
Filter Cartridges
To replace filter cartridges, call the In-Sink-Erator Answerline,
or visit our website at www.insinkerator.com.
Lasts Twice
as Long!
43386 Filter Owner's Manual.qxd 9/26/02 11:58 AM Page 4 Greg Leber Jobs:39237 ISE HWD Owner's Manual:43386 HWD Filter

In-Sink-Erator Division
Emerson Electric Co.
4700 21st Street
Racine,WI 53406-5093
http://www.insinkerator.com 43386 0902
Other Products Available from In-Sink-Erator:
Household Food Waste Disposers, Food Service Equipment, Filtration Systems, Hot
Water Dispensers, Compact Electric Water Heaters, International Products
In-Sink-Erator® is a registered
trademark of In-Sink-Erator, a
division of Emerson Electric
Co.All other trademarks are
property of their respective
companies.
©2002 In-Sink-Erator
Autres produits disponibles auprès de In-Sink-Erator :
Broyeurs de déchets alimentaires, équipement de service d’alimentation, systèmes de
filtration, distributeurs d’eau chaude, chauffe-eau électriques compacts,
produits internationaux
In-Sink-Erator® est une
marque de commerce
déposée de In-Sink-Erator,
une filiale de Emerson Electric
Co.Toutes les autres marques
déposées sont la propriété de
leurs entreprises respectives.
©2002 In-Sink-Erator
Otros productos de In-Sink-Erator:
Trituradoras de desperdicios domésticos, equipos para servicio de alimentos, sistemas
de filtración, dispensadores de agua caliente, calentadores eléctricos de agua
compactos, productos internacionales
In-Sink-Erator® es una marca
comercial registrada de In-
Sink-Erator, una división de
Emerson Electric Co. El resto
de las marcas comerciales son
propiedad de sus respectivas
compañías.
©2002 In-Sink-Erator
43386 Filter Owner's Manual.qxd 9/26/02 11:58 AM Page 1 Greg Leber Jobs:39237 ISE HWD Owner's Manual:43386 HWD Filter