Inspiration Tecotherm Neo User manual

Tecotherm Neo
Quick Set-up Guide

Prior to operation: Refer to Tecotherm Neo Instructions for Use.
You will need:
Tecotherm Neo
TECOmed Coolant Fluid
Fill-Up Set
Connecting Hoses
Aqua Pad/ Wrap Mattress
Interlayer
Pre-Fill Mattress
A minimum volume of 250 ml TECOmed fluid must be filled into mattress
Connect the male mattress connectors to the female connectors of the
fill-up bottle
Turn bottle until cap is directed downwards and keep it in a position 0.5m
higher than the mattress
Fill-Up the Tecotherm Neo with TECOmed fluid
Ensure mattress hoses are disconnected from the lower pair of device ports (6)
Undo fill-up bottle and fill with TECOmed fluid up to the 450 ml mark
Connect fill-up set to refill port connector counterparts at the device interface (7)
Green marked connector always fits in to the right hand side port.
Turn on the Tecotherm Neo, select and start treatment mode
“Constant mattress temperature”
Turn bottle until cap is directed downwards
Wait until the fluid level inside fill-up bottle stops falling
Now quit treatment mode
Attach the prefilled mattress to hoses and connect to lower device ports (6)
Connect the green marked male connector of the fill-up bottle to the right refill
port connector. This time do not connect the left hand male connector
Select “Constant mattress temperature” and fill the Tecotherm with another
100 ml of TECOmed fluid
Disconnect fill up set
Note: Move mattress around to ensure all air bubbles have been removed.
Optional:
Rectal Probe
Skin Probe
Treatment Modes
In the main menu select the treatment mode required by scrolling to one of,
Complete Treatment Mode, Servo Mode or Constant Mattress Temperature Mode
Once selected, scroll down and select the parameters to be changed
as appropriate
Once all parameters are selected press start
Note: If using either servo mode you will be asked to insert a rectal probe into the
patient and connect to the Tecotherm Neo, if doing so it is recommended to do so
by approx 6 cm without forcing the probe so as not to cause internal damage to t
he patient.
Caution: In servo modes the Tecotherm Neo first pre-conditions the mattress
temperature, once rectal probes are inserted press ‘START’ to commence servo
mode otherwise the Tecotherm Neo stays in constant mattress mode.
FEMALE CONNECTORS
NON- RETURN VALVE
GREEN CONNECTOR
(7) FILL UP CONNECTION*
PORTS
(T5) ALARM SILENCER*
(1) POWER ON/OFF*
(6) MATTRESS
CONNECTION PORTS*
*Numbers relate to those shown
in the Instructions for Use.
Tecotherm Neo Quick Set-up Guide

During Treatment
During treatment the screen will display the measured temperature in large
numbers. In Servo Modes it will appear in ‘Green’ if temperature is +/- 0.5 °C
from set or red if it falls outside of this range. In the Constant Mattress
Temperature mode it will appear in Blue (within +/- 0.5 °C) or Black if not.
If at any time all parameters need to be seen press the ‘details’ button
From time to time top-up the mattress with TECOmed fluid as described above
– this can be done without changing the treatment mode or stopping treatment
Note: At any time all parameters can be changed by pressing ‘change settings’,
and selecting the parameter to change.
Shut Down
Once finished, the Tecotherm Neo can be powered off in the main menu
If required, the last treatment can be downloaded to a USB stick by selecting
‘Export treatment data’ on the main menu
Turn the Tecotherm Neo off using the option on the main menu
Unplug hoses and mattress and clean with alcohol wipes
500-400(2)
Inspiration Healthcare Ltd
Gildor House, West Street,
Earl Shilton, Leicester, LE9 7EJ, UK
Tel: [phone]
Fax: [phone]
Email: [email protected]
Web: www.inspiration-healthcare.com
24 hour emergency hire and support call
[phone]
The details given in this leaflet are correct at time of going
to press. The company reserves the right to improve the
products shown.
Distributed by: