Amico Roll Stand INE-0909-12-12-F4-M User manual

Installation Instructions
Infusion Extension Arm

2 Amico Accessories Inc.
Preface
IMPORTANT, PLEASE READ CAREFULLY
Thank you for your purchase with Amico Accessories Inc.
The Amico Roll Stand is designed for long lasting performance, provided the user complies with assembly and
maintenance procedures. This instruction manual is your guide to ensuring that you get the best performance out
your equipment. Amico Accessories is not responsible for any damage as a result of (but not limited to) abuse and
other malfunctions that may be a direct or indirect result of failure to comply with the instructions provided in this
manual.
Please Note these Key Words and Symbols
WARNING: Steps where extra care should be taken to prevent injuries and damage.
NOTE: Steps that point out helpful information.
Medical Facility Responsibilities
Preventive maintenance checks must be performed regularly to maintain the quality and performance of this product.
Any parts that may be broken, missing, worn, distorted, or contaminated in any way should not be used and all
affected parts should be replaced immediately. Should the necessity of any repair be suspected; please contact your
local distributor or call 877-264-2697.

www.amico.com 3
Table of Contents
Section 1: Product Specifications 4-5
Features 4
Specifications 4
Technical Drawings 4
Product Classifications 5
Section 2: Installation Preparation 6-7
What’s in the Box? 6
Parts Legend 6
Tool 7
Section 3: Installation 7-10
Assembling Post to Swivel Disks 7
Identifying Top and Bottom Posts 7
Installation to Mounting Platform 8
Mounting to Monitor Rail System (MRS) (-M) 8
Installation to Horizontal Rail System (ARS) (-AT) 9
Double Rail 9
Single Rail 9
Mounting to Amico Vertical Rail System (-V) 10
Section 4: Device Installation 10-11
Mounting IV Bags 10
Mounting Infusion Pump 11
Section 5: Adjustments 11-12
Rotation of Arms 11
Adjusting Tensions at the Head 12
Hook Adjustment 12
Section 6: Cable Management 13
Section 7: Troubleshooting, Preventative Maintenance, Storage, & Cleaning 13-14
Troubleshooting 13
Preventative Maintenance 14
Storage 14
Cleaning 14
Warranty 15

4 Amico Accessories Inc.
Features
• Available with single or double extension options for customization
• Four (4) optional hooks for mounting IV Bags safely and securely
• 360° post rotation for easy access
• 180° arm rotation for maneuvering and positioning
• Swivel tension adjustable to user preference
• Includes integrated cable management for improved workflow
• Post diameter of 1.25"(3.2 cm) for mounting multiple infusion pumps
• Post length of 12"(30.5 cm) each, providing 24"(61 cm) of total mounting space
• Direct mounting options available for headwall, pendant, and anesthesia machines
• Easy to clean using standard medical grade materials
Specifications
• Single extension (-0900): 19.6"(49.80 cm) L x 28.5"(72.4 cm) H
• Double extension (-0909): 30.7"(78.0 cm) L x 28.5"(72.4 cm) H
• Total product weight rating: 40 lbs (20.41 kg) total
• Weight rating per hook: 5 lbs (2.6 kg)
• Post diameter: 1.25"(3.2 cm)
• Post length: 12"(30.5 cm) each
Technical Drawings
Section 1: Product Specifications
19.6
28.5
11.1
R11.9
R17.5
INE-0900-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
1
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0900-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
DIAMETER 11.1"28.2 cm RADIUS 17.5"44.5 cm
RADIUS 11.9"30.2 cm
19.6
28.5
11.1
R11.9
R17.5
INE-0900-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
1
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0900-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
30.7
28.5
11.1
R28.6
R10.4
R23.0
INE-0909-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
3
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0909-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
19.6
28.5
11.1
R11.9
R17.5
INE-0900-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
1
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0900-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
28.5"72.4 cm
19.6"
49.8 cm
30.7
28.5
11.1
R28.6
R10.4
R23.0
INE-0909-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
3
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0909-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
DIAMETER 11.1"28.2 cm
RADIUS 23"58.4 cm
RADIUS 28.6"72.6 cm
RADIUS 10.4"26.4 cm
30.7
28.5
11.1
R28.6
R10.4
R23.0
INE-0909-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
3
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0909-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
30.7
28.5
11.1
R28.6
R10.4
R23.0
INE-0909-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
3
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0909-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
30.7
28.5
11.1
R28.6
R10.4
R23.0
INE-0909-12-12-F4-M Project #: 0617
NOTE: HOOK CONFIGS WILL NOT FOLD
UP COMPLETELY FLUSH AGAINST WALL
UNLESS SPECIFIED
ALL DIMENSIONS IN INCHES
BREAK ALL EDGES .005 - .010
ANGLE TOLERANCES
1
FRACTIONAL TOLERANCES 1/32
DECIMAL TOLERANCES:
.XX
.03
.XXX
.005
.XXXX
.0005
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
3
4
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
HP
2018-01-15
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
INE-0909-12-12-F4-M
20180115-4406
PROJECTION
www.amico.com
28.5"
72.4 cm
30.7"
78 cm

www.amico.com 5
Section 1: Product Specifications
Product Classifications
INE - XXXX - 12 - 12 - YY - Z
V
AMICO VERTICAL
RAIL ADAPTER
M
MRS RAIL ADAPTER
AT
AMICO HORIZONTAL
RAIL ADAPTER
00
NO HOOK
F4
FIXED 4 HOOK
0900
SINGLE EXTENSION
0909
DUAL EXTENSION
DOUBLE EXTENSION
PART NUMBER: INE09091212F4M

6 Amico Accessories Inc.
Section 2: Installation Preparation
What’s in the Box?
NOTE: Please ensure that your contents match the list as outlined below. If not, please contact Amico
Accessories at 1-877-264-2697.
Parts Legend
Extension Arm Top Post (4 hooks) OR
Top Post (no hook) Bottom Post
Hardware Kit (2x sets)
Cable Management (2x)
Installation Manual (1x)
MANUFACTURER
PART NUMBER PART DESCRIPTION
H-MPF-1032-12 Screws
4x HOOKS
(X-IVHOOK-31618-J)
CIRCULAR LABEL
TOP POST (X-TRL-125-12)
3x LOCK WASHERS
(H-WLM-10)
BOTTOM SWIVEL DISK
(MON-SWIV-DISK)
BOTTOM POST
(X-TRL-125-12)
3x SCREWS
(H-MPF-1032-12)
3x LOCK WASHERS
(H-WLM-10)
TOP PLATE
(MON-CPU-DISK)
TOP SWIVEL DISK
(MON-SWIV-DISK-T)
BOTTOM PLATE
(MON-CPU-DISK)
3x SCREWS
(H-MPF-1032-12)
MON-CPU-DISK Bottom Plate
MON-SWIV-DISK-T Top Swivel Disk
MON-CPU-DISK Top Plate
H-WLM-10 Lock Washers
X-TRI-125-12 Top Post
MON-SWIV-DISK Bottom Swivel Disk
X-TRI-125-12 Bottom Post
X-IVHOOK-31618-J Hooks
Figure 1 Figure 2

www.amico.com 7
Section 2: Installation Preparation
Section 3: Installation
Tools
NOTE: AMICO DOES NOT PROVIDE TOOLS NECESSARY FOR ASSEMBLY.
Assembling Posts to SWIVEL DISKS
1. Using a #2 Phillips head screwdriver or bit (not provided), insert 3x PAN HEAD SCREWS through 3x LOCK
WASHERS, through BOTTOM PLATE of TOP POST and into TOP SWIVEL DISK as shown in Figure 3.
2. Repeat Step 1 for the BOTTOM POST as shown in Figure 3 (fasteners will go through TOP PLATE of BOTTOM POST
into BOTTOM SWIVEL DISK).
Identifying TOP and BOTTOM POSTS
For no hook configurations, the TOP POST will have a CIRCULAR LABEL on the TOP PLATE.
3. For hook configurations, the TOP POST will have 4x HOOKS instead of a TOP PLATE. (Figure 4)
#2 Phillips Screwdriver 1/8"Hex Key
4x HOOKS
(X-IVHOOK-31618-J)
CIRCULAR LABEL
TOP POST (X-TRL-125-12)
3x LOCK WASHERS
(H-WLM-10)
BOTTOM SWIVEL DISK
(MON-SWIV-DISK)
BOTTOM POST
(X-TRL-125-12)
3x SCREWS
(H-MPF-1032-12)
3x LOCK WASHERS
(H-WLM-10)
TOP PLATE
(MON-CPU-DISK)
TOP SWIVEL DISK
(MON-SWIV-DISK-T)
BOTTOM PLATE
(MON-CPU-DISK)
3x SCREWS
(H-MPF-1032-12)
Figure 3 Figure 4

8 Amico Accessories Inc.
Section 3: Installation
Installation to MOUNTING PLATFORM
WARNING: Do not attempt to mount the Infusion Arm with any devices already installed. Doing so could
result in damage or injury.
WARNING: Ensure RAIL is stable and properly installed before mounting.
Mounting to MONITOR RAIL SYSTEM (MRS) (-M)
1. Lift up the INFUSION ARM and guide the MOUNTING ADAPTER into the top of the MRS RAIL as seen in Figure 5.
2. Once the ARM is positioned at the desired height in the MRS RAIL, tighten all 4x SET SCREWS to the tightest
possible position on the MOUNTING ADAPTER using a 1/8"hex key.
BOTTOM
STOPPER
ONE-WAY
STOPPER
MRS RAIL: LENGTH FOR REPRESENTATIONAL USE ONLY
MRS
MOUNTING
ADAPTER
SET SCREWS
Figure 5 Figure 6

www.amico.com 9
Section 3: Installation
Installation to HORIZONTAL RAIL SYSTEM ARS AT
Double Rail
1. If mounting to a headwall, determine the best location for installation and remove the MOUNTING ADAPTER
CHANNEL COVER to access the 2x SCREWS connecting the CHANNEL to the BOTTOM ARS ADAPTER. Remove
the 2x SCREWS to free the BOTTOM ARS ADAPTERS (Figure 7). Install this BOTTOM ARS ADAPTER into the
BOTTOM RAIL by angling the upper lip into the inside lip of the BOTTOM ARS RAIL, pull the LEVER back against
the ARS ADAPTER and push the ADAPTER into the RAIL. Once secure, release the LEVER. (Figure 8)
2. Mount the Infusion Arm by installing the remaining ARS ADAPTER onto the TOP ARS RAIL in the same way as
step 1, ensuring the 2X HOLES on the BOTTOM ARS ADAPTER can be seen through the MOUNTING ADAPTER
CHANNEL, secure the MOUNTING ADAPTER CHANNEl to the BOTTOM ARS ADAPTER using SCREWS and LOCK
WASHERS you removed in step 1. (Figure 9)
3. Replace the CHANNEL COVER onto the MOUNTING ADAPTER CHANNEL.
Single Rail
1. If mounting to a single rail, angle the upper lip of the ARS ADAPTER of the MOUNTING ADAPTER CHANNEL into
the inside lip of the RAIL, hold the tab on the ARS ADAPTER and push into the RAIL. Once secure, release the tab
and ensure the SUPPORT BLOCK is sitting flush and firmly against the wall. (Figure 10)
2. Install the locking bar by placing it on top of the ARS ADAPTER of the MOUNTING ADAPTER CHANNEL so it is
squeezed by the ADAPTER and ARS RAIL.
SCREW, LOCK
WASHERS
COVER
MOUNTING
ADAPTER
CHANNEL
Figure 7
MOUNTING
ADAPTER CHANNEL
ARS RAIL
SUPPORT BLOCK
MOUNTING ON A
SINGLE ARS
Figure 10
MOUNTING
ADAPTER CHANNEL
ARS ADAPTER
INSTALLED
ARS
RAIL
MOUNTING ON A
HEADWALL
Figure 9
ARS ADAPTER
LEVER ON ARS
ARS RAIL
Figure 8

10 Amico Accessories Inc.
Section 4: Device Installation
Mounting IV Bags
NOTE: The Infusion Extension Arm is rated for 40 lbs total
with a maximum of 5 lbs per HOOK (hook configurations
only) and 15 lbs mounted to the BOTTOM POST.
• To mount IV Bags (hook configurations only), carefully hang IV
Bags from HOOKS attached to the TOP POST using the IV Bag
mounting space. It is advised to only mount 1x IV Bag per HOOK.
Section 3: Installation
Mounting to Amico VERTICAL RAIL SYSTEM V
WARNING: To prevent the V-ADAPTER from falling down the CHANNEL, ensure that the SCREWS are
fastened as tight as possible. Verify no movement is present between the ADAPTER and the RAIL.
NOTE: Before installation, ensure 2x NUTS and 2x KNOBS are loose to the tip of the V-ADAPTER SCREWS.
This will allow the HEAD OF THE V-ADAPTER SCREWS to adjust into the profiles of the VERTICAL RAIL.
1. Angle the Infusion Arm from either side and guide the HEADS OF THE TOP AND BOTTOM SCREWS into the
channel of the RAIL. (Figure 11-13)
2. Ensure the FLANGE on the ADAPTER is properly aligned with the RAIL.
3. Position the ARM to the desired height and fasten 2x KNOBS and 2x NUTS (12 mm) to the tightest possible
position. Cover the NUTS with the 2x PLASTIC CAPS provided. (Figure 14)
VERTICAL
RAIL
END CAP
SCREW
KNOBS
TIGHTEN
THUMB
SCREWS AND
NUTS
FLANGE
HEAD OF
THE TOP SCREW
HEAD OF THE
BOTTOM SCREW
V-ADAPTER SCREW
SIDE OF THE
V-ADAPTER
SIDE OF
THE VRS
Figure 11 Figure 12 Figure 13 Figure 14
4x HOOKS
(X-IVHOOK-31618-J)
POST (TOP)
[X-TRI-125-12]
POST (BOTTOM)
[X-TRI-125-12P)
Figure 16

www.amico.com 11
Mounting Infusion Pump
Follow the Infusion Pump manufacturer’s instruction to mount device onto the 1.25"(3.2 cm) diameter post.
Section 4: Device Installation
Section 5: Adjustments
Rotation of Arms
WARNING: The Infusion Arm has approximately 180° rotation. Ensure proper clearance to avoid collision.
NOTE: If the Arm becomes too difficult to rotate or too loose, please contact Amico Accessories.
NOTE: Adjusting the rotational tension of the Extension Arms can be done by loosening or tightening the
BOLT at the joints of the Arms and the ADAPTER using a 12"socket at the HEAD, and ¾"socket wrench or
equivalent tool at the ADAPTER end. Be careful not to over loosen.
To rotate the PRIMARY ARM, push on the side of the PRIMARY ARM (near the center). To rotate the SECONDARY ARM
(double extension configurations only), hold the PRIMARY ARM and push the side of the SECONDARY ARM.
Figure 17 shows the product in the straight position while Figure 18 shows the product in folded position
(SECONDARY ARM folded in).
HEAD
[X-LPM-ADA]
BOTTOM POST
[X-TRI-125-12]
3 x SCREWS
[H-MPF-1032-12]
3 x WASHERS
[H-WLM-10]
PLATE
[MON-CPU-DISK]
SWIVEL DISK
[MON-SWIV-DISK]
NUT
[H-LNUT-M8-NYL-FL]
Figure 2
PRIMARY ARM
Figure 1
PRIMARY ARM
SECONDARY ARM
PROJECT #: 617
FOR USE WITH INE-___-12-12-__
CUSTOMER
Adjustments:
WARNING: The
INE ARM(s) has approximately 180 rotation. Ensure proper clearance to avoid collision.
ARM Rotation:
To rotate the
PRIMARY ARM , push on the side of the PRIMARY ARM (near the center). To rotate the SECONDARY ARM (INE-
0909-12-12-__-__ configurations only), hold the
PRIMARY ARM and push on the side of the SECONDARY ARM . Figure 1
shows the product in the straight position while Figure 2 shows the product in folded position (
SECONDARY ARM folded in)
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
3
6
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
-
HP
2018-01-19
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
-
INE-___-12-12-__-__
20180119-4415
PROJECTION
www.amico.com
Figure 17 Figure 18
PRIMARY ARM
PRIMARY ARM
SECONDARY ARM

12 Amico Accessories Inc.
1. Remove BOTTOM POST by removing the
3x SCREWS and 3x WASHERS to expose
NUT.
2. Tighten or loosen NUT using a ½"socket
(not provided) until desired tension is
achieved (tighten for higher tension and
loosen for lower tension).
3. Reassemble BOTTOM POST by inserting
the 3x SCREWS through 3x WASHERS
through PLATE in BOTTOM POST and into
SWIVEL DISK. Ensure all SCREWS are tight.
Section 5: Adjustments
Hook Adjustment
The HOOKS can be rotated 360°.
To Rotate HOOKS
• Grasp 2x HOOKS and carefully rotate to desired position. Figure 20 shows
the HOOKS rotated 45°.
NOTE: If rotating HOOKS is difficult, see previous section (Adjusting
Tension at the Head).
HEAD
[X-LPM-ADA]
BOTTOM POST
[X-TRI-125-12]
3 x SCREWS
[H-MPF-1032-12]
3 x WASHERS
[H-WLM-10]
PLATE
[MON-CPU-DISK]
SWIVEL DISK
[MON-SWIV-DISK]
NUT
[H-LNUT-M8-NYL-FL]
ADAPTER END
PROJECT #: 617
FOR USE WITH INE-___-12-12-__
CUSTOMER
Adjustments:
WARNING: The
INE ARM(s) has approximately 180 rotation. Ensure proper clearance to avoid collision.
NOTE: If the arm becomes difficult to rotate, or too loose, please contact Amico Accessories: 1-877-264-2697
NOTE: Adjusting the rotational tension of the extension arms can be done by loosening or tightening the bolt at
the joints of the arms and the adapter using a 1/2" socket at the
HEAD and 3/4” socket wrench or equivalent tool at the adapter
end. Be careful not to overloosen.
Adjusting Tension at the
HEAD :
WARNING: Do not attemp to adjust the tension with any devices mounted to the
INE, unload the INE before proceeding.
Remove
BOTTOM POST by removing the 3 x SCREWS and 3 x WASHERS to expose NUT .1.
Tighten or loosen
NUT using a 1/2" socket (not provided) until desired tension is achieved (tighten for higher tension and 2.
loosen for lower tension).
Reassemble
BOTTOM POST by inserting the 3 x SCREWS through 3 x WASHERS, through PLATE in BOTTOM POST 3.
and into SWIVEL DISK . Ensure all SCREWS are tight.
.
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
4
6
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
-
HP
2018-01-19
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
-
INE-___-12-12-__-__
20180119-4415
PROJECTION
www.amico.com
HEAD
[X-LPM-ADA]
BOTTOM POST
[X-TRI-125-12]
3 x SCREWS
[H-MPF-1032-12]
3 x WASHERS
[H-WLM-10]
PLATE
[MON-CPU-DISK]
SWIVEL DISK
[MON-SWIV-DISK]
NUT
[H-LNUT-M8-NYL-FL]
ADAPTER END
PROJECT #: 617
FOR USE WITH INE-___-12-12-__
CUSTOMER
Adjustments:
WARNING: The
INE ARM(s)
has approximately 180
rotation. Ensure proper clearance to avoid collision.
NOTE: If the arm becomes difficult to rotate, or too loose, please contact Amico Accessories: 1-877-264-2697
NOTE: Adjusting the rotational tension of the extension arms can be done by loosening or tightening the bolt at
the joints of the arms and the adapter using a 1/2" socket at the
HEAD
and 3/4” socket wrench or equivalent tool at the adapter
end. Be careful not to overloosen.
Adjusting Tension at the
HEAD
:
WARNING: Do not attemp to adjust the tension with any devices mounted to the
INE,
unload the
INE
before proceeding.
Remove
BOTTOM POST
by removing the 3 x
SCREWS
and 3 x
WASHERS
to expose
NUT
.1.
Tighten or loosen
NUT
using a 1/2" socket (not provided) until desired tension is achieved (tighten for higher tension and
2.
loosen for lower tension).
Reassemble
BOTTOM POST
by inserting the 3 x
SCREWS
through 3 x
WASHERS,
through
PLATE
in
BOTTOM POST
3.
and into
SWIVEL DISK
. Ensure all
SCREWS
are tight.
.
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
4
6
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
-
HP
2018-01-19
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
-
INE-___-12-12-__-__
20180119-4415
PROJECTION
www.amico.com
ADAPTER END
3x SCREWS
[H-MPF-1032-12]
BOTTOM POST
[X-TRI-125-12]
3x WASHERS
[H-WLM-10]
PLATE
[MON-CPU-DISK]
NUT
[H-LNUT-M8-NYL-FL]
SWIVEL DISK
[MON-SWIV-DISK]
HEAD
[X-LPM-ADA]
Figure 19
HEAD
[X-LPM-ADA]
BOTTOM POST
[X-TRI-125-12]
3 x SCREWS
[H-MPF-1032-12]
3 x WASHERS
[H-WLM-10]
PLATE
[MON-CPU-DISK]
SWIVEL DISK
[MON-SWIV-DISK]
NUT
[H-LNUT-M8-NYL-FL]
Figure 1
PROJECT #: 617
FOR USE WITH INE-___-12-12-F4-__
CUSTOMER
Adjustments:
HOOK Adjustment:
The HOOKS can be rotated 360 .
To rotate HOOKS:
Grasp 2 HOOKS and carefully rotate to desired position. Figure 1 shows the HOOKS rotated 45
1.
NOTE: If rotating HOOKS is difficult, see section "Adjusting Tension at the HEAD" from previous page.
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
5
6
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
-
HP
2018-01-19
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
-
INE-___-12-12-__-__
20180119-4415
PROJECTION
www.amico.com
Figure 20
WARNING: Do not attempt to adjust the tension with any devices mounted. Unload the INFUSION ARM
before proceeding.
Adjusting Tension at the Head

www.amico.com 13
SYMPTOM POSSIBLE CAUSE SOLUTION
Adapter is loose in rail Loose mounting configuration Tighten set screws and refer to instructions
(Installation to Mounting Platform).
Top or bottom post is loose on extension Improper installation to posts Remove screws and refer to instructions (Assembling
Posts to Swivel Disks).
Adapter cannot raise or lower Channel stoppers engaged Ensure channel stopper is unfastened and removed
prior to rail installation. Reinstall upon completion.
Section 6: Cable Management
Section 7: Troubleshooting, Preventive Maintenance,
Storage, & Cleaning
NOTE: Double extension configurations may use up to 2x CORD HOLDERS while single extension
configurations may only use 1x CORD HOLDER as shown below in Figures 21 and 22.
HEAD
[X-LPM-ADA]
BOTTOM POST
[X-TRI-125-12]
3 x SCREWS
[H-MPF-1032-12]
3 x WASHERS
[H-WLM-10]
PLATE
[MON-CPU-DISK]
SWIVEL DISK
[MON-SWIV-DISK]
NUT
[H-LNUT-M8-NYL-FL]
CORD HOLDER
[X-AHM-CRDHLDR]
ARM
[X-AHM-EXT-35]
PROJECT #: 617
FOR USE WITH INE-___-12-12-__-__
CUSTOMER
Cable Management:
For cable management please refer to
AHM-FIT_-___-__-__ (Project 481) user manual for routing cables through
CORD HOLDER. Please note however that the
CORD HOLDER sits on the ARM instead of on the AHM arm.
INE-0909-12-12-__-__ configurations may use up to 2 CORD HOLDERS while INE-0900-12-12-__-__ configuartions may
only use 1 as shown below in FIgures 1 & 2 respectively.
Figure 1 Figure 2
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
66
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
-
HP
2018-01-19
-
-/-/-
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
-
INE-___-12-12-__-__
20180119-4415
PROJECTION
www.amico.com
ARM
[X-AHM-EXT-35]
CORD HOLDER
[X-AHM-CRDHLDR]
Troubleshooting
Figure 21 Figure 22

14 Amico Accessories Inc.
Section 7: Troubleshooting, Preventive Maintenance,
Storage, & Cleaning
Preventive Maintenance
It is recommended that once every three (3) months, all locks, bolts, and screws are visually inspected for signs of
product wear and tear or damage. Check the product for device looseness in the mount or orientation, and ensure the
adapter is secured to the rail or wall channel system. Ensure the set screws on the channel and two thumb screws are
fastened to the tightest possible position and ensure device is secure.
Storage
DO NOT place the transformer in any damp or dripping location. It should be stored in a ventilated and dry location.
Cleaning
WARNING: The cleaning chemicals and methods below are not meant for controlling any infections. It shall
be the responsibility of the hospital or the hospital’s infection control officer to sanitize the equipment.
WARNING: Please do not spray any chemical directly onto the Infusion Extension Arm. Apply onto a soft cloth
and wipe clean to prevent chemicals getting into the internal components of the Infusion Extension Arm.
The mounting assembly can be cleaned with most mild, non-abrasive solutions commonly used in the hospital
environment (e.g. diluted bleach, ammonia, alcohol). The surface finish will be permanently damaged by strong
chemical and solvents such as acetone and trichloroethylene. Steel wool or other abrasive material should never be
used. Damage caused by the use of unapproved substances or processes will not be warranteed. It is recommended
that you test any cleaning solution on a small area of the RS model that is not visible to verify compatibility. Never
submerge the RS model and do not allow liquids to enter. Wipe any cleaning agents off of the RS models immediately
using a water-dampened cloth. Dry thoroughly after.
No Acetone
Acetone is a colorless,
mobile, flammable
liquid.
ACETONE
Figure 23
No Trichloroethylene
Trichloroethylene is a
chlorinated hydrocarbon
commonly used as an
industrial solvent.
TRICHLOROETHYLENE
Figure 24

www.amico.com 15
www.amico.com
Amico Accessories Inc. warrants all mounting accessories to be free from defects in material and workmanship for a period of
twelve (12) months from the date of shipment. Within this period Amico Accessories Inc. will repair or replace any part which is
proven to be defective.
Amico Accessories Inc. will warrant its materials to be free from defect for an additional period of four (4) years, (five [5] years from
the date of shipment). Within this period, Amico Accessories Inc. will replace any part which is proven to be defective, at no charge.
Shipping and Installation costs after the first twelve (12) months will be borne by the Customer.
This warranty is valid only when the product has been properly installed according to Amico Accessories Inc. specifications, used
in a normal manner and serviced according to factory recommendations. It does not cover products that are not manufactured by
Amico Accessories Inc. It does not cover failures due to damage which occurs in shipments or failures which result from accidents,
misuse, abuse, neglect, mishandling, alteration, misapplication or damage that may be attributable to acts of God.
Amico Accessories Inc. shall not be liable for incidental or consequential damages resulting from use of equipment.
All claims for warranty must first be approved by Amico Accessories Inc. A valid Return Goods Authorization (RGA) number must
be obtained from Amico Accessories Inc. prior to commencement of any service work. Warranty work, which has not been pre-
authorized by Amico Accessories Inc., will not be reimbursed.
AMICO ACCESSORIES INC. DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY.
The distributor and/or dealer are not sanctioned to create verbal warranties about the product described in this agreement. Any
statements will not be honored or be made part of the agreement of sale. This document is the final complete and exclusive terms
of the agreement.
THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES.
Amico Accessories Inc. shall not, under any circumstances be liable for incidental or consequential damages including, but not
limited to, profit, loss of sales or injuries to person(s) or property. Correction of noncompliance as noted above will result in
completion of all liabilities of Amico Accessories Inc., whether based on agreement, neglect or changed materials, designs or
specifications without notice.
All claims for warranty must first be approved by Amico Accessories Inc. Service Department: [e-mail] or
1.877.264.2697. A valid Return Goods Authorization number must be obtained from Amico Accessories Inc. prior to commencement
of any warranty claim.
Amico Accessories Inc. | 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada
Tel: [phone] | Fax: [phone]
Warranty Policy - Equipment Mounting Solutions
AA-WARRANTY 08.16.2017
Warranty

www.amico.com
AAIMINFUSIONEXTENTIONARM 09.26.2022
Amico Accessories Inc. | 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada
Toll Free Tel: [phone] | Tel: [phone] | Fax: [phone]
Email: [email protected] | www.amico.com