Inspired Flight IF1200 User manual

Physical Set-Up Guide
IF1200 Hexacopter

1
TABLE OF CONTENTS
..........................................................
..........................................................
..........................................................
..........................................................
..........................................................
..........................................................
..........................................................
..........................................................
1. Unboxing ..........................
2. Attach Legs .....................
3. Unfold Arms ....................
4. Install GPS .......................
5. Install Battery .................
6. Attach Gimbal .................
7. Power On Vehicle ..........
8. Attach Propellers ...........
2
3
5
6
7
8
9
10

Unlock the drone case by unhooking the (7) hatches
by pulling upward.
Lift the top of the case open until it rests upright.
Remove the IF1200 from the case using the two straps
located on top of the drone.
Rest IF1200 on a flat surface (min. 2ft x 2ft)
Remove other the materials inside the case and place
them on a separate table
STEP 1:
STEP 2:
STEP 3:
STEP 4:
STEP 5:
STEP 1 STEP 3 STEP 4
2
UNBOXING
1

3
ATTACH LEGS
Remove the landing gear located in the wide slots within
the drone case.
Locate the two sections of landing gear. The shorter piece
(with rubber caps) are the “feet” of the drone, while the
longer tubes are the “legs.”
Loosen the clamp on the shorter piece (feet).
Insert the longer tube (legs) perpendicularly into the
shorter tube (feet).
Tighten the clamp by twisting the lever until fully tightened.
(Repeat steps 1-5 again for the other landing gear)
Unfold the two arms that are located next to the leg insert
slots on the drone.
Insert the leg into the drone body, ensure the notch at the end of
the tube aligns with the key inside the corresponding socket.
Fully secure the leg by twisting the lever until it is fully tightened.
Ensure the o-rings are on the lower half of the tube assembly,
closer to the feet.
The tightening lever can be repositioned to a convenient
position by pulling it outward and rotating it.
STEP 1:
STEP 2:
STEP 3:
STEP 4:
STEP 5:
STEP 6:
STEP 7:
STEP 8:
STEP 9:
STEP 10:
2

STEP 7 STEP 8
STEP 4 STEP 5 STEP 6
4
ATTACH LEGS
2

5
Unfold the six aircraft arms into upright position by lifting
them until it clicks.
The shoulders should lock the arms securely into place
(metal clips flip up).
STEP 1:
STEP 2:
STEP 1 STEP 2
UNFOLD ARMS
3

6
Lift the GPS up, and locate the two clips on each side of
the GPS base.
Secure the clips onto the main frame & pull upward, locking
the GPS in place.
Make sure clips are securely in place, and not loose.
STEP 1:
STEP 2:
STEP 3:
STEP 1 STEP 2 STEP 3
INSTALL GPS
4

7
Ensure the velcro straps on top of the vehicle are unfastened
& moved out of the way so that the battery can be placed
on top of the vehicle.
Grab your fully charged smart battery and place it securely
in the alignment trays.
Ensure the battery is centered, and the label is facing up.
The battery lead should be on the opposite side of the GPS.
Connect the velcro straps tightly over the battery to secure it
into place.
Connect the battery lead to the corresponding lead on the
vehicle, making sure it is seated fully.
STEP 1:
STEP 2:
STEP 3:
STEP 4:
STEP 5:
STEP 2 STEP 4 STEP 5
INSTALL BATTERY
5

8
Ensure marks on the top & bottom parts of the gimbal are aligned.
The mark on the ring should be aligned with the unlocked icon
shown in the first image (below).
Attach the bottom part to the top part (keep arrows aligned).
Rotate the ring clockwise until the mark on the ring aligns with
the lock icon.
STEP 1:
STEP 2:
STEP 3:
STEP 4:
STEP 2 STEP 3 STEP 4
ATTACH GIMBAL
6

Press the power button on near the rear of the vehicle.
The LED indicator light will turn on when the aircraft is on,
and beeping will occur during the initialization sequence.
The LED on the GPS mast will turn blue as it searches for
a signal.
STEP 1:
STEP 2:
STEP 3:
STEP 1 STEP 2
POWER ON UAV
7
9

Locate the correct propeller for each motor.
Three of the IF1200’s motors spin clockwise, and have
black connecting points. The other threee motors spin
counterclockwise and have silver connecting points.
Attach the prop to the corresponding color of the connector
on the motor (Silver to silver, black to black).
Ensure the white dots line up with the corresponding motor,
place each propeller on its motor.
Make sure each propeller is fully seated, with the bottom of
the aluminum quick-disconnect parallel to the motor face.
Tighten the propellers on the motors to .9Nm using the
provided torque screwdriver.
Twist screwdriver until you hear a loud click, ensuring the
propeller is securely mounted.
STEP 1:
STEP 2:
STEP 3:
STEP 4:
STEP 5:
STEP 6:
STEP 7:
STEP 4 STEP 5 STEP 6
ATTACH PROPS
8
10