Intel ISP2150 - Server Platform - 0 MB RAM User manual

ISP2150 2U Rack Server Platform
Quick Start Guide
A Guide for Technically Qualified Assemblers of Intel®Identified
Subassemblies/ Products
Before You Begin
FCC Declaration of Conformity.................................................................................................. 4
Cautions and Warnings...............................................................................................................6
Product Regulation Compliance..................................................................................................7
Safety Compliance......................................................................................................................7
Electromagnetic Compatibility (EMC)....................................................................................... 7
ISP2150
Opening and Closing the Front Bezel .........................................................................................8
Locking and Unlocking the Front Bezel .....................................................................................9
Attaching and Removing the Front Bezel...................................................................................9
Installation
Open the Cover...........................................................................................................................9
Installing a Microprocessor....................................................................................................... 10
Installing Memory..................................................................................................................... 11
Installing a Hard Drive..............................................................................................................13
Installing Add-in Cards............................................................................................................. 14
Installing a Slim-Line CD-ROM Drive.....................................................................................16
Removing a Diskette Drive.......................................................................................................17
Re-Installing a Diskette Drive...................................................................................................17
Close the Cover......................................................................................................................... 17
Installing the Front Bracket and Racking Your System............................................................18
Installing the Front Bracket in a Cabinet...................................................................................18
Installing the Front Bracket in a Center-Mount, Relay Rack .................................................... 20
Installing the Rail Kit and Racking Your System (Optional Accessory)...................................21
Technical Reference
Front Panel Controls and Indicators..........................................................................................25
Back Panel Connectors.............................................................................................................26
Jumpers..................................................................................................................................... 27
Server Board Components........................................................................................................ 29
Getting Help.......................................................................................................................................30
Order Number: A13687-001

4 ISP2150 2U Rack Server Platform Quick Start Guide
The ISP2150 2U Rack Server Platform Product Guide can be found at http://channel.intel.com/isp/
Copyright © 2000 Intel Corporation. All rights reserved. No part of this document may be copied, or reproduced in any form,
or by any means without prior written consent of Intel.
Intel Corporation (Intel) makes no warranty of any kind with regard to this material, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. Intel assumes no responsibility for any errors that may
appear in this document. Intel makes no commitment to update nor to keep current the information contained in this
document.
†Third-party brands and trademarks are the property of their respective owners.
Before You Begin
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation
5200 N.E. Elam Young Parkway
Hillsboro, OR 97124
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment to an outlet on a circuit other than the one to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.

ISP2150 2U Rack Server Platform Quick Start Guide 5
ICES-003 (Canada)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils
numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils
Numériques”, NMB-003 édictée par le Ministre Canadian des Communications.
(English translation of the notice above) This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the interference-causing equipment standard entitled
“Digital Apparatus,” ICES-003 of the Canadian Department of Communications.
BSMI (Taiwan)
The following EMC Warning along with the BSMI ID number 3882B139 is located on the outside rear
area of the product:
VCCI (Japan)
(English translation of the notice above.) This is a Class B product based on the standard of the Voluntary
Control Council For Interference (VCCI) from Information Technology Equipment. If this is used near a
radio or television receiver in a domestic environment, it may cause radio interference. Install and use the
equipment according to the instruction manual.
When used near a radio or TV receiver, it may become the cause of radio interference.
Read the instructions for correct handling.
This equipment has been tested for radio frequency emissions and has been verified to meet CISPR 22
Class B.

6 ISP2150 2U Rack Server Platform Quick Start Guide
Cautions and Warnings
WARNINGS
Pressing the power button does not turn off power to this server. Disconnect the
server from its power source and from any telecommunications links, networks, or
modems before doing any of the procedures described in this guide. Failure to do
this can result in personal injury or equipment damage. Some circuitry in the server
may continue to operate even though front panel power button is off.
This guide is for qualified technical personnel with experience installing and
configuring servers.
Read and adhere to all warnings, cautions, and notices in this guide and the
documentation supplied with the chassis, power supply, and accessory modules. If
the instructions for the chassis and power supply are inconsistent with these
instructions or the instructions for accessory modules, contact the supplier to find out
how you can ensure that your computer meets safety and regulatory requirements.
CAUTION
Electrostatic discharge (ESD) can damage server components. Do the described
procedures only at an ESD workstation. If no such station is available, you can provide
some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of
the computer chassis.

ISP2150 2U Rack Server Platform Quick Start Guide 7
Product Regulation Compliance
See the ISP2150 2U Rack Server Platform Product Guide for all applicable safety standards,
electromagnetic compatibility (EMC) regulations, and product certification markings.
Intended uses: This product was evaluated for use in computer rack cabinets within computer rooms and
similar locations. Other uses may require further evaluation.
Safety Compliance
USA: UL 1950 – CSA 950-95
Canada: UL certified to CSA 950-95 for Canada (product bears the single UL mark for U.S. and
Canada)
Europe: German GS Mark – ERG to EN60950
International: IEC60 950
Australian /
New Zealand:AS/NZ 3260 (IEC60 950 including national AU deviations)
Electromagnetic Compatibility (EMC)
USA: FCC CFR 47 Part 15, Class B
Canada: ICES-003 Class B
Europe: EN55022, Class B
EN55024 (Immunity)
EN61000-3-2 Limit for Harmonic Current Emissions
International: CISPR 22, Class B
Australian /
New Zealand:AS/NZ 3548, Class B limits (CISPR 22)
Japan: VCCI Class B (CISPR 22 B limit)

8 ISP2150 2U Rack Server Platform Quick Start Guide
ISP2150
Congratulations on the purchase of your new Intel®ISP2150 system. This Quick Start introduces you to
your new system, guides you through rack kit installation, and helps you get the system started.
The following procedures describe how operate the system’s front bezel, which covers the front panel
controls and indicators. For a description of the front panel features, refer to Front Panel Controls and
Indicators.
Opening and Closing the Front Bezel
With the bezel open you have access to all
of your system's front panel functions and
indicators. With the bezel closed you can
protect critical functions and still view the
system's indicators.
To open the bezel, do the following:
1. Stand in front of the chassis and grasp
the edges of the bezel from each side.
2. Gently pull the bezel towards you
until it begins to separate from the
chassis.
3. As the bezel separates from the
chassis, allow it to swing to its open
position situated below the chassis.
To close the bezel, gently raise it upwards.
The hinging mechanism will guide the
bezel into the correct position where it will
snap shut.

ISP2150 2U Rack Server Platform Quick Start Guide 9
Locking and Unlocking the Front Bezel
The bezel can be locked and unlocked to prevent unwanted access to the system.
To lock the bezel:
1. Remove the keys from inside the bezel (they should be taped to the inside).
2. Close the bezel and insert the key into the lock. Turn the lock counterclockwise until it stops (about a
quarter turn). The bezel is now locked and cannot be opened.
To unlock the bezel, insert the key into the lock and turn the lock clockwise until it stops (about a quarter
turn). The bezel is now unlocked and can be opened again.
Attaching and Removing the Front Bezel
The front bezel can be installed or removed from the system.
To attach the bezel:
1. With the LED light tunnels located at the top of the bezel, push in the arms on either side of the bezel
far enough so that the tabs on the ends of the arms can be inserted into the holes in the chassis.
2. Insert the tabs into the holes in the handles on the chassis. Make sure the tabs on each side of the
bezel are completely in the holes in the handles.
To remove the bezel:
1. With the bezel opened, gently push the metal hinge arms located on each side of the bezel in towards
the middle of the unit.
2. Push the arms far enough in so that the tabs on the end of the arms are completely out of the holes in
the handles on the chassis. The bezel should now be able to be removed.
3. The bezel should now be able to open and close easily and completely.
Installation
Follow these instructions to get your sever to the point where you can load an operating system on it.
Open the Cover
1. Loosen the three screws on the rear of the system.
2. Pull the cover back and remove it from the chassis.

10 ISP2150 2U Rack Server Platform Quick Start Guide
Installing a Microprocessor
The server supports up to two Intel®Pentium®II or Pentium III processors (with 100 MHz system bus).
If you are installing two processors, make sure they are the same speed, voltage, and stepping.
OM09315
C
E
F
D
A
B
OM09328
B
A
1. Remove the new processor from its
anti-static package and place it on a
grounded, static free surface or
conductive foam pad.
2. Attach the small end of the power
cable to the fan connector on the
S.E.C. cartridge, then attach the large
end (B) to the 3-pin connector on the
server board.
3. Orient the processor so that the heat
sink faces the I/O connectors. Slide
the processor into the retention module.
Push down firmly, with even pressure
on both sides of the top, until the
processor is seated.
4. To lock in the processor, push the
latches inward on the retention module
until they click into place. The latches
must be secured for proper electrical
connection of the processor.
5. After you have installed the processor,
you must configure its speed in BIOS
set-up.
CAUTION, Single-Processor
Configurations
If you install only one processor in a
system, it must go in the primary
connector (closest to the DIMM
sockets). With a single-processor
configuration, you must install a
termination board and termination
latch assembly (A) in the empty
secondary connector (B) to ensure
proper operation of your system. A
termination board is provided with
your system.

ISP2150 2U Rack Server Platform Quick Start Guide 11
Installing Memory
OM09318
The server only supports 100 MHz
PC/100-compliant SDRAM.
•Install from 32 MB to 2 GB of
unbuffered memory, using up to four
single or double-banked DIMMs
Or
•Install from 32 MB to 2 GB of
registered memory, using up to four
single or double-banked DIMMs

12 ISP2150 2U Rack Server Platform Quick Start Guide
Installed DIMMs must be the same speed and either all registered or all unbuffered. For a list of supported
memory, call your service representative or visit the Intel Support website:
http://support.intel.com/support/motherboards/server/l440gx/compat.htm
CAUTION
Use extreme care when installing a DIMM. Applying too much pressure can damage the socket.
DIMMs are keyed and can be inserted in only one way.
Mixing dissimilar metals may cause later memory failures resulting in data corruption. Only install
DIMMs with gold-plated edge connectors in gold-plated sockets.
To install your memory:
1. Open your server.
2. Holding the DIMM only by its edges, remove it from its anti-static package.
3. Orient the DIMM so that the two notches in the bottom edge of the DIMM align with the keyed
socket.
4. Insert the bottom edge of the DIMM into the socket, and press down firmly on the DIMM until it
seats correctly.
5. Gently push the plastic ejector levers on the socket ends to the upright position.
6. Repeat the steps to install each DIMM.
7. Ensure that no cables are protruding from the server chassis and then close the server.
8. Connect all external cables and the power cord to the server.
9. Turn on the monitor and then the server.