Intelligent Home Alecto User manual

-1-
www.intelligenthomeonline.com
Alecto Video Door System
2-wire Series
Installation and User Manual
Digital Touch Screen 7 inch Monitor

-2-
PRECAUTIONS
●Read this manual through before using the product.
●Slots or openings in the back of the monitor, are provided for ventilation
and to ensure reliable operation of the video monitor or equipment and
to protect if from overheating. These openings must not be blocked or
covered. The monitor should never be placed near or over a radiator or
heat register and should not be placed in a built-in installation such as a
bookcase unless proper ventilation is provided.
●All parts should be protected from violence vibration. And not allow be
impacting, knocking and dropping.
●For clean the LCD screen, using hands or wet cloth is forbidden.
●Please do the cleanness with soft cotton cloth, please do not use the
organic or chemical clean impregnate. If necessary, please use pure
water or dilute soap water to clean the dust.
●Image distortion may occur if the video door phone is mounted too close
●Please keep away the video door monitor from wet, high temperature,
dust, and caustic and oxidation gas in order to avoid any unpredictable
damage.
●Do NOT open the device in any condition, call the administrator for help
if there is any problem or mulfunction happens.

-3-
1.Monitor Parts and Functions ...........................................................................................4
2.Monitor Mounting..............................................................................................................5
3.Main Menu. ........................................................................................................................5
4.Answering a Door Call ......................................................................................................5
4.1 Electric Lock Release ..................................................................................................6
5.Monitor Setup Instructions ................................................................................................6
5.1 Sounds Settings............................................................................................................6
5.2 Date & Time Settings...................................................................................................7
5.3 Rename & Monitoring Time Setting............................................................................7
5.4 Do Not Disturb.............................................................................................................8
5.5 Screen Modes and Talk Volume Adjustment ...............................................................8
5.6 Call Record(register of calls) .......................................................................................9
5.7 Pictures and Video Recording......................................................................................9
5.8 Pictures and Video Playback........................................................................................10
5.9 Multi Monitor System..................................................................................................10
5.10 Intercom Function......................................................................................................12
6.Call Divert Function ..........................................................................................................13
6.1 Staircase Light .............................................................................................................14
6.2 Restore to Default ........................................................................................................14
6.3 Languages ....................................................................................................................14
6.4 Changing colour of LED on the button........................................................................15
7.Specications.....................................................................................................................16
CONTENT

-4-
DIP
DIP1&2
DIP3
DIP State
Reserved
Description
Set OFF if monitor is in the middle of the line (daisy chain connection)
Set ON if monitor is at the end of the line (daisy chain) or connected to a DBC4 (star)
There are 3 x DIP switches on the back of the monitor. Only DIP-3 should be set On
or Off depending on the location of the monitor, and the connection method used
DIP switches Settings
Additional call button con-
nection port
Additional Call Button
Additional call button can be connected to
a monitor according to the diagram. Please
note: There will be no video on the monitor
when somebody rings this call button
Set DIP-3 On for a single monitor system
1 2 3
ON
1 2 3
ON
1 2 3
ON
DIPS
ON
1 2 3
Speaker
1. Monitor Parts and Functions
Digital TFT LCD Screen
Talk/MON Button
Menu Button
Unlock Button
Microphone
Mounting Hooks
Cable Connection Port
L1
L2

-5-
145~160 cm
00:30 Front Door
2. Monitor Mounting
1. Use the screws to x the mounting bracket on the wall
2. Hang the Monitor on the mounting bracket rmly
3. Main Menu
Touch the screen anywhere while in-
standby mode. The main menu page will
be shown as pictured
4. Answering a Door Call
When door station is rung, the monitor comes On with video.
To start conversation touch Talk/Monitor on the button
o r Talk icon on the screen
To end conversation touch Talk/Monitor button once again.
Monitor will shut down automatically after 40 seconds

-6-
_
INSTALLER SETUP 123
About
Local Address 00.00
Video Standard AUTO
System Verson 00.01.00
Display Driver 1.0
Front 1.0
UI 1.0
1.Touch icon on
the main menu page
2.Touch UNLOCK
button and hold for 2s
3.A digital keypad will
be shown
5. Monitor Setup Instructions
5.1. Sounds Settings
Touch settings icon and choose “Sounds”.
Here you can set ringtones for door stations and Inter-
com between rooms and Day/Night ring volume.
“United” means same ring tone will be set for eve-
rything, “Separate”- different ring tones. Touch
icon to exit and return to home page
4.1 Electric Lock Release
There are two icons Lock1 and Lock2 which means you can have up to 2 electric locks connected
and opened independently. If system connected to a lock, remember to set unlocking time and
lock mode. Settings are changed on the “Installer Setup” page. To access the page, touch “Intel-
ligent Home” icon on the left hand side, at the bottom. Touch and hold “Unlock” button for 2
seconds to open digital keypad page. Using the keypad, type in the following codes:
8010 # for Power-on-to open lock
8011 # for Power-off-to open lock
To set the unlocking time, use codes 8401-8499 # for 1 to 99 seconds
Example: Type in 8401 # for 1 second unlocking time, 8499 # for 99 secs unlocking time
You can open the lock by touching UNLOCK Button or touching icon on the screen

-7-
5.2.Date & Time Settings
Touch settings icon and choose “Date & Time”. Here you can set date and time.
“Sync system clock” allows to set date and time on one monitor in multiple monitor system and
sync all monitors to the same settings quickly.
Touch icon to exit and return to home page.
5.3. Rename & Monitoring Time Settings
Touch settings icon and choose “More”. Here you can give descriptions to your door sta-
tions and CCTV cameras i.e. Front Door, Back Door, Gate. Touch the icon of the door station
or CCTV camera you want to rename, the digital keypad will open. Type in your new descrip-
tion and touch the arrow button to save.
You can set duration of manual monitoring time on this page as well. Touch icon to exit
and return to home page
How to set date and time format
Setting should be done via Installer Setup
Code 8008 to set the date format as Month/Day/Year
Code 8009 to set the date format as Day/Month/Year
Code 8012 to set the time format as 12 hour system
Code 8013 to set the time format as 24 hour system

4 screen modes can be selected:
the bottom of a screen shows the remaining time.
-8-
Do Not Disturb function will set the monitor to not react to door station calls. Touch icon
and choose desired settings: Do Not Disturb for 1 hour, 8 hours, Always. Running clock
on
DS-3_
DOOR3 RENAME abc
Do Not Disturb
Normal
For 1 Hour
For 8 Hours
Always
Time remaining: 00:58:32
5.4. Do Not Disturb
5.5. Screen Modes and Talk Volume Adjustment
To adjust them, open video from door station manually and then touch settings icon
Scene mode selection:
Normal, Bright, Soft and
User
You can also adjust Brightness , Colour, Talk Volume

-9-
Call Record 01/05
06-23 15:22 Bedroom
06-18 20:54 Front Door
06-12 11:06 Back Door
05-29 08:39 AlKitchen
05-27 21:43 Front Door
04-20 13:16 Gate
Call Record 01/05
06-23 15:22 Bedroom
06-18 20:54 Front Door
06-12 11:06 Back Door
05-29 08:39 Kitchen
05-27 21:43 Front Door
04-20 13:16 Gate
Maximum number of records: 100
New records will overwrite oldest automatically
5.6. Call Record (register of calls)
All calls received by monitors either from the door station or from other
monitors in the system (if installed) can be viewed in “Call Record”. Missed
calls are marked by red arrows. Missed calls from door station have viewable
pictures or video clips (if SD card was inserted). Calls from other monitors
have no picture/video record; you only can see what time someone called via
Intercom
5.7. Pictures and Video Recording
When door station is rung, the monitor will record a picture of the visitor automatically. The
monitor has built-in memory for 1000+ pictures. An additional Micro SD card (up to 32GB)
can be inserted to increase memory storage. The SD card will enable video clips recording.
Clips are 10s or 15 s each. Video clips with sound can be recorded only when “Talk” button is
activated. Otherwise video clips will not have sound. Pictures and video clips can be down-
loaded fom the monitor via SD card.
Manual recording: if nobody rings the door bell but you see something via manual monitoring
and want to take a picture or video clip of the event, touch “Record” icon. If you want
your manual video recording with sounds, remember to also hit the “Talk” button

Code
-10-
_
INSTALLER SETUP 123
About
Local Address 00.00
Video Standard AUTO
System Verson 00.01.00
Display Driver 1.0
Front 1.0
UI 1.0
1.Touch icon on
the main menu page
2.Touch UNLOCK
button and hold for 2s
3.A digital keypad will
be shown
5.8. Pictures and Video Playback
Touch Playback icon to play recorded pictures or videos
icon to Start/Pause the playback
Touch
Image:008/020 2014/06/23 14:36:55
5.9. Multi Monitor System
There are two ways of connecting multiple monitors:
1. Daisy Chain - each monitor connects to the next monitor
2. Star Connection - all monitors connect to a central point
Up to 16 video monitors can be connected in a house system. Up to 4 monitors in each apart-
ment for Apartment systems. Each monitor in either system must be programmed with a“User
Code”- the address.
How to program the “User Code” (address) for Daisy Chain connection
Go into Installer Setup by touching “Intelligent Home” icon on the left hand side, at the bot-
tom. This will open the “About” page. Touch and hold “Unlock” button for 2 seconds, and the
digital keypad page will open.
Programming of code 8000# for the rst monitor in a chain makes it the Master monitor
8001# to program the monitor as Slave 1
Code 8002# to program the monitor as Slave 2
Code 8003# to program the monitor as Slave 3
If there are more than three Slave monitors in the system, program them as Slave 1, 2, 3 as
well.
Code 8001 # to program the monitor as Slave 4
Code 8002 # to program a monitor as Slave 5 and so on
In addition to User Code programming, last monitor in the chain have to have DIP-3 set On
(end of line)