Intelligent Home MR9L User manual

Video Door Entry System
user manual
This manual covers MR9L and MR9L/ID Door station
www.intelligenthomeonline.com
1
RF CARD
2 3
4 5 6
7 8 9
*0 #
CALL
UNLOCK
TALK/MON
IN-USE
Use Cat-5 Network Cable

PRECAUTIONS
●Read this manual through before using the product.
●Slots or openings in the back of the monitor, are provided for ventilation and to
ensure reliable operation of the video monitor or equipment and to protect if
from overheating. These openings must not be blocked or covered. The monitor
should never be placed near or over a radiator or heat register and should not
be placed in a built-in installation such as a bookcase unless proper ventilation
is provided.
●All parts should be protected from violence vibration. And not allow be
impacting, knocking and dropping.
●For clean the LCD screen, using hands or wet cloth is forbidden.
●Please do the cleanness with soft cotton cloth, please do not use the organic or
chemical clean impregnate. If necessary, please use pure water or dilute soap
water to clean the dust.
●Image distortion may occur if the video door phone is mounted too close to
magnetic field e. g. Microwaves, TV, computer etc.
●Please keep away the video door monitor from wet, high temperature, dust,
and caustic and oxidation gas in order to avoid any unpredictable damage.
●Do NOT open the device in any condition, call the administrator for help if there
is any problem or mulfunction happens.

CONTENT
1. Door station ----------------------------------------- 1
2. Indoor Monitor --------------------------------------- 3
3. Distributor ------------------------------------------ 4
4. Power Supply ---------------------------------------- 5
5. System Connection ------------------------------------ 6
6. Flat Code and Time Setting ------------------------------ 7
7. Door station Configurations------------------------------ 8
8. Key Fob Settings (only for MR9L/ID)------------------------13
9. Connect 4 Door stations with C5-MDS(Optional) --------------15
10. Specifications ---------------------------------------18

-1-
1. Door station
LCD screen
Night view LED
Camera Lens
Loudspeaker
Digital Keypad
ID car window
Screw cover
Microphone
1
RF CARD
2 3
4 5 6
7 8 9
*0 #
The MR9L Door station is a digital station with 128*128 pixels LCD screen, color CCD
camera, night view LED, and digital keypad.
Visitors can call the apartment by dial the Flat Code (apartment number) on the keypad. If
they don’t know the Flat Code (apartment number), they can search the name list on the
screen. If the door station is in standby, visitors need to press '9#' to display the user name
list. Then, using the '8' / '0' key scroll next/last page. Finally, use the 1 to 7 key to call the
desired flat.
Residents can open the door using their unique Unlock Code (four-digit PIN code). If the
door station is in standby mode, press '#' key, then input the four-digit PIN to open the
door.
1.1 Calling and Unlock Operation

-2-
1. Cut a hole on the wall with the size of 345(H)*115(W)*38(D)mm, and wire the cable.
2. Put the mounting box into the hole and fix it with screws.
3. Connect all the cables, and then fix the Door station body into the mounting box.
4. Fix the front panel on the Door station body.
5. Put back the screw cover on the top of the front panel.
1
2
3
4
5
1.2 Open the Front Panel:
1.3 Mount the Door station:
1. Take off the screw cover 3. Take off the front panel
2. Screw off the screw

2. Indoor Monitor
-3-
145~160 cm
Wire the system correctly (see Connection chapter) then hang the Monitor on the
Mounting Bracket firmly.
CALL
UNLOCK
TALK/MON
IN-USE
LCD Touch Screen
LED indicator
UNLOCK button
CALL button
TALK/MON button
Speaker
Ventilation Vent
Connection Port
C5-MC connector
Microphone
2.1 Parts and Functions
2.2 Monitor Mounting

3. Distributor
-4-
C5-F4 distributor
In-use Data
140mm
88mm
62mm
Power
upward
84mm
70mm
13mm
ABCD
Trunk Bus
P-P+
HI
120
32mm
36mm
A/B/C/D port: Connect to Monitors
Trunk Bus: Bus cable input/output. Connect to last
C5-F4(or doorstation), and connect to next C5-F4
P-: Power negative input. (Ground)
P+: Power positive input. (15~18V DC)
set to 120 for the last C5-F4
on the building, the others
must be set to HI.
The Distributor is used to connect Monitors to the bus line. One Distributor can connect 4
Monitors. There are two mounting measures: bar mounting or dirrect wall mounting.
Bar mounting:
Dirrect wall mounting:

4. Power Supply
Cables and distance:
Power supply cable: RVVP 2*1.0 mm2
Distance: from Door station to the last distributor: 600 m Max.
Data Cable: Catalogue-5 cable, 0.5 mm2or bigger
Distance: from Door station to the last Distributor: 200m Max.
from Distributor to Monitor: 30m Max.
The system uses a PS-2 power supply. It provides the power for the door station,
distributors, monitors and electric lock.
The maximum numbers of monitors it can support is twenty. If there are more than twenty
monitors in the system an additional power supply is needed. Each extra twenty monitors
will require an additional PS-2 power supply .
ML+
ML-
P+
P-
L-
L+
L-
L+
PTR1
SW3
LK-TEST
UNLOCK
AC-IN
DC-OUT
18V-OUT
ON OFF
BAT+
BAT-
AC
AC
VR1
AC
AC
GND
13~15V-OUT
SW1
E-lock (power-on-to-unlock type, 18V DC)
E-lock (power-off-to-unlock type, 13~16V DC)
ML+, ML- of door station
P+, P- of the door
station or distributor
247 mm
287 mm
ON
OFF
100~240 V AC
-5-

5. System Connection
C5-F4
C5-F4
Connect to next C5-F4
ML-
18 V DC lock
L- L+ L-
-
L+
+
ML+
ML- ML+
Power Supply
P- P+
ON
OFF
SW1 P-
P+
Doorstation
1
RF CARD
2 3
4 5 6
7 8 9
*0 #
-6-

6. Flat Code and Time Setting
-7-
Home Intellegent System
monitor
intercom
setup
exit
alarm
Home Intellegent System
Doorstation Tone -- 01
Camera Tone -- 10
Guard unit Tone -- 05
No Disturb Set -- off
Installation...
Exit
Home Intellegent System
8
7
6
#
0
9
3
0
2
1
*
* * *
5
4
Password:
Home Intellegent System
Alarm in/out delay -- 40
Date and Time set...
Room Address...
Other settings...
Informations...
Exit
Home Intellegent System
TIME
DATE
2009 10 21
1 1 3 5
:8
7
6
#
0
9
3
2
1
*
5
4
Every Monitor must be set to a Flat Code, so that
the Door station can identify the Monitor. For
example, if a Monitor is set to a code 0101, when
the visitor press 0101 on the Door station, only the
Monitor with the code 0101 will ring.
1. Power the monitor. Enter into the Main --> setup
--> installation --> (input password: 2412) to open
the configuration page.
2. Select and enter Flat Address... item to modify
the flat code.
3. On the installation screen, select Date and Time
Set item to enter the time setting page, use the
touch screen to input the correct Time and Date.

7. Door station Configurations
-8-
7.1 About Flat code
7.2 About Debug Mode
7.3 About Default Set
The Flat Code (also called monitor address) is a unique code assigned to each monitor, to
identify different monitors; each monitor has a unique flat code.
All settings can be changed by going into the Debug Mode.
When the settings of the door station are significantly wrong, the quickest way to solve the
problem is to revert back to the default settings.
When the screen is Debug State, press '#9009' to exit.
When Door Station is in
standby, press '#' key
In Debug State, press '#'
key twice
In Program Guide, press
'1' key
press '9' key, then input
Admin Code and'#'to
confirm
input '9008', then input the
Admin Code.(66666666 by
default)
Debug State menu is
now launched
Video Entry System
[ 9 0 0 8 ]
1
2
3
4
5
6
7
8
#
0
*
9
Video Entry System
System Ready
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
System Ready
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
Press 1~9 to select
---------------------------
[8] System Maintain
[7] Card Management
[6] Access Security
[5] Operating Options
[4] Information
[3] Monitor Program
[2] Unlock
Setting
>>
P
rogram Guide <<
[1] Configuration
-9. Default Set
---------------------------
[9] Advanced Config
Video Entry System
---------------------------
[1] Configuration
* Back
Press 1~9 to select
---------------------------
-9. Default Set
-8. Admin. Code
-6. Camera Power On [0]
-7. Doorplate Mode [1]
-5. Intercom Video [1]
-4. Monitoring Nbrs [2]
-3. Unlock Timing [1]
-2. Multi DS Mode [0]
-1. Net Address [001]
-9. Default Set

-9-
7.4 Change Admin Code (administrator password)
7.5 Change Unlock Code (door open password)
The Admin Code is the password to access the door station Debug Mode. The default Admin
Code is '66666666'. Note that if the Default Set has been applied, the Admin Code will also
be set to default.
There are two Unlock Codes which can be used. The user can use either one of them to
open the door. They are '1111' and '2222' by default.
On the Debug State, press [# #] to get into the Program Guide, press[2] to open the Unlock
Setting menu, then enter[1] or [2] to change the Unlock Code. as shown below:
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
Press 1~9 to select
---------------------------
[8] System Maintain
[7] Card Management
[6] Access Security
[5] Operating Options
[4] Information
[3] Monitor Program
[2] Unlock
Setting
>>
P
rogram Guide <<
[1] Configuration
-9. Default Set
---------------------------
[9] Advanced Config
Video Entry System
---------------------------
[1] Configuration
* Back
Press 1~9 to select
---------------------------
-9. Default Set
-8. Admin. Code
-6. Camera Power On [0]
-7. Doorplate Mode [1]
-5. Intercom Video [1]
-4. Monitoring Nbrs [2]
-3. Unlock Timing [1]
-2. Multi DS Mode [0]
-1. Net Address [001]
-8. Admin. Code
Video Entry System
* Back
# Save
<********>
--------
Change Admin Code
>>
[1][8]
In Debug State, press '#'
key twice
Input the new Admin Code
and then press '#'key to
confirm
press '1' press '8'
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
Press 1~9 to select
---------------------------
[8] System Maintain
[7] Card Management
[6] Access Security
[5] Operating Options
[4] Information
[3] Monitor Program
[1] Configuration
>>
P
rogram Guide <<
[2] Unlock Setting
---------------------------
[9] Advanced Config
Video Entry System
---------------------------
[2] Unlock Setting
* Back
Press 1~9 to select...
---------------------------
-8. Change Program Code
-7. Code Nbrs [0]
-6. Code Check ...
-5. Code Range ...
-4. Code Mode [1]
-3. Code Error Alert [0]
-2. Unlock Code 2 [2222]
-1. Unlock Code 1 [1111]

-10-
7.6 Change Door station language
7.7 Change Ringtone
There are 8 operating languages can be selected:
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
Press 1~9 to select
---------------------------
[8] System Maintain
[7] Card Management
[6] Access Security
[5] Operating Options
[4] Information
[3] Monitor Program
[1] Configuration
>>
P
rogram Guide <<
[9] Advanced config
---------------------------
[2] Unlock Setting
Video Entry System
---------------------------
[9] Advanced Config
* Back
Press 1~9 to select
---------------------------
-9. Timing
-8. Admin. Code
-6. Monitor Version [0]
-7. Call Mode [0]
-5. HMC [0]
-4. Name List [1]
-3. Voice Memo [0]
-2. Image Memo [0]
-1. Tone Select [11]
-8. Language [1]
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
Press 1~9 to select
---------------------------
[8] System Maintain
[7] Card Management
[6] Access Security
[5] Operating Options
[4] Information
[3] Monitor Program
[1] Configuration
>>
P
rogram Guide <<
[9] Advanced config
---------------------------
[2] Unlock Setting
Video Entry System
---------------------------
[9] Advanced Config
* Back
Press 1~9 to select
---------------------------
-9. Timing
-6. Monitor Version [0]
-7. Call Mode [0]
-5. HMC [0]
-4. Name List [1]
-3. Voice Memo [0]
-2. Image Memo [0]
-1. Tone Select [11]
-8. Language [1]
Video Entry System
>>[9][8]
* Back #Save
Language
-
(0~7)
In Debug State, press '#'
key twice
Input the number for each
language according to the
language table, press '#' to
confirm.
press '9' press '8'
0. Chinese
1. English
2. French
3. Portuguese
4. Spanish
5. German
6. Italian
7. Dutch
There are 15 different ringtones, as shown below:

7.8 Name List function
The name list can be edited by using the digital keypad of the door station. The input
method is similar to mobile phones. By default the name list function is ON.
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
Press 1~9 to select
---------------------------
[8] System Maintain
[7] Card Management
[6] Access Security
[5] Operating Options
[4] Information
[3] Monitor Program
[1] Configuration
>>
P
rogram Guide <<
[9] Advanced config
---------------------------
[2] Unlock Setting
Video Entry System
---------------------------
[9] Advanced Config
* Back
Press 1~9 to select
---------------------------
-9. Timing
-8. Admin. Code
-6. Monitor Version [0]
-7. Call Mode [0]
-5. HMC [0]
-4. Name List [1]
-3. Voice Memo [0]
-2. Image Memo [0]
-1. Tone Select [11]
-4. Name List [1]
Video Entry System
>>[9][4]
* Back #Save
Name List
-
(0~2)
Video Entry System
>>[9][4].2 Name List
* Back #Save
1. Add
2. Modify
3. Initialise
Press 1~3 to select
Video Entry System
[Add_008]
* Back #Save
Line 1:
Line 2:
_ [ ]
[ ]
(123)
To use the namelist function, the Name List item must be set to '1'(enable), which is default.
Press '2#' to enter Press '1' to add new
names, press '2' to modify
the existing names, press
'3' to initialise to default.
Flat code and Name
input page.
The first 4 digits are for the Flat Code input (the address of the flat). After 4 digits have
been input, it will switch to Line 1 and the input mode will switch to ABC input mode
automatically. Line 2 is for the names that are too long for one line. After the name has
been input, press '#' to save.
Button 1: Switch the letter between
capitalization and lowercase.
Button 2: A, B, C, (a, b, c)
Button 3: D, E, F, (d, e, f)
Button 4: G, H, I, (g, h, i)
Button 5: J, K, L, (j, k, l)
Button 6: M, N, O, (m, n, o)
Button 7: P, Q, R, S, (p, q, r, s)
Button 8: T, U, V, (t, u, v)
Button 9: W, X, Y, Z, (w, x, y, z)
Button * : Cancel
Button 0: Space blank, İ, Ş, Ç, Ü, Ğ, Ö
-11-

Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
* Back
Press 1~8 to select
---------------------------
[8] Simulate Calling...
[7] Voltage Measuring...
[6] Monitor Property
[5] Online Searching...
[4] < >Display Alarm
[3] < >Display Net
[1] < >Volume Adjust
---------------------------
[2] < >Auto Dial Back
Video Entry System
---------------------------
>>Online Searching<<
>>Debug Tools<<
#Search
[----]~[----]
(Search Range)
* Back
Video Entry System
---------------------------
>>Online Searching<<
[0101] Online
[0102] Online
[0103] Linking Error
[0104] Online
[0201] Online
[0202] Online
[0203] Online
[0204] Linking Error
[0301] Linking Error
* Back
* Back
“Online Search” is a very useful function that can help the installer to easily check the
connectivity of all the Monitors. Please note, Online does not mean via the internet. In
Debug Mode, press [2 #] to get into the Debug Tools, press [5] to open the “Online Search”
menu, as shown below:
Search Range: input the Flat Codes and the end Flat codes.
The first two digits of the Flat Code are the floor number;
the last two digits are the Maximum flats quantity on each
floor. For example, input the range from 0101 to 0804, will
search 8 floor and 4 flats on each floor. You will see the
connection status of the selected apartments.
7.9 Using software
-12-

8. Key Fob Settings (only for MR9L/ID)
This chapter explains how to configure the key fob function on MR9L/ID. Please note: for
the Door station without the Key Fob function (the MR9L), keep the settings by default.
The key fob is used to open the lock. Total 500 key fobs can be registered with one Door
station. When swiping the fob on the fob reader on the Door station, the distance must be
less than 3 millimetres.
Key Fobs must be registered on the Door station. Only then can fobs be recognised and
open the door.
To use the key fobs:
1. Enable the ID card/key fob function;
2. Register the Fobs.
8.1 Enable the ID card/key fob function
8.2 Register the Key Fobs
Video Entry System
---------------------------
>> DEBUG STATE <<
---------------------------
1-# Download from PC
0-# Redial Last Nbrs
#-# Program Guide
<
●
> Display Alarm
< > Display Net Data
< > Auto Dial Back
< > Volume Adjust
---------Options----------
< > Guard Unit Online
2-# Debug Tools
Video Entry System
* Back
Press 1~9 to select
---------------------------
[8] System Maintain
[7] Card Management
[6] Access Security
[5] Operating Options
[4] Information
[3] Monitor Program
[2] Unlock
Setting
>>
P
rogram Guide <<
[1] Configuration
---------------------------
[9] Advanced Config
V i d e o E n t r y S y s t e m
------------------------- - -
[ 6 ] A c c e s s S e c u r i t y
* Back
P r e s s 1 ~ 5 t o s ele c t
------------------------- - -
-5. U n l o c k V e r i f y [0]
-4. Clo c k ...
-3. ACS A d d r e s s [121 ]
-2. P a s s i v e A d dre s s [1]
- 1 . A cce s s F u n c tion [ 1 ]
-1. Access Funtion [1]
When the Door station is in standby, press [#] --> [9008] -->Password([66666666 by
default]) to get into the Debug Mode Menu, as shown below.
All the registered key fobs are called User Cards/User Key Fobs. New fobs/cards need to be
registered one by one to the Door station to become a User Card/User Key Fob; and every
User Card/User Key Fob is related to a certain Monitor Address (Flat code).
Registered User Cards/Key Fobs can be deleted from the Door station and once unregistered
will not open the door anymore. They can also be re-registered again to become a valid
User Card/User Key Fob. There are two ways to delete User Cards/User Key Fobs:
1. Delete by card: show the unwanted card(s) when the Door station is in Delete Card Mode
2. Delete by Flat Code: will delete all the registered User Cards related to that Flat Code.
Press [##] --> [1] -->[1] to get into the Access Function page and set the value to 1, the
function is now enabled.
Note: the 4. Clock... item is for time setting (which will display on the top of standby
welcome screen, clock function is only available for MR9L/ID).
-13-

8.3 Delete User Cards
V i deo E n t r y S y s t e m
>>[ 7 ][1]
* B a c k # S a v e
P l e a se i n put M . C o d e
[--- - ]
A d d C a r d
C a r d : 15977131
Updated
Vide o Ent r y Sys t e m
>>[7 ] [ 1 ]
* Bac k # S a v e
S h o w t h e C a r d
0101
A d d C a r d
C a r d : 159771 3 1
U p d a t e d
V i d e o E n t r y S y s t e m
>>[7 ] [ 1 ]
* B a c k # S a v e
0101
A d d C a r d
Card: 1 5977131
Upd a t e d
C a r d : 15977131
Updated
Vide o Ent r y Sys t e m
>>[7 ] [ 2 ]
* Bac k # S a v e
Show the Card
Delete By Card
C a r d : 159771 3 1
U p d a t e d
V i d e o E n t r y S y s t e m
>>[7 ] [ 2 ]
* B a c k # S a v e
M.Code: 0101
Card 1382428255
Upd a t e d
Delete By Card
C a r d : 15977131
Updated
Vide o Ent r y Sys t e m
>>[7 ] [ 3 ]
* Bac k # S a v e
Please input M.Code
[----]
Delete By M.Code
C a r d : 159771 3 1
U p d a t e d
V i d e o E n t r y S y s t e m
>>[7 ] [ 3 ]
* B a c k # S a v e
0101
Upd a t e d
Delete By M.Code
When the Doors tation is standby, press [#] --> [9008] -->Password([66666666 by default])
to get into the Debug Mode Menu, then Press [##] --> [7] Card Management -->[1] Add
Card to get into the Add Card page as shown below.
Flat Code is asked. input the flat code Show the card on the a
Updated will show on
the screen, then show
next card.
Delete by Card/Fob: goto [# #]
Program Guide -->[7] Card
Management --> [2] Delete by
Card, to enter delete by card
page, as shown on the right, then
show the cards you want to delete
one by one.
Delete by Flat code: goto [# #]
Program Guide -->[7] Card
Management --> [3] Delete
by M.Code, to enter delete by
flat code page, as shown on the
right, then input the flat code
to which the cards are related,
Updated will show on the screen
if delete successfully. Note that all
registered cards related to the flat
code will be deleted.
-14-

9.1 Configure the Multi Door station Mode
9. Connect 4 Door stations with C5-MDS(Optional)
The C5-MDS is designed for the C5-800 apartment intercom system, to connect multiple
Door stations(Maximum 4) ) in one system.
To connect the C5-MDS, 3 steps must be done:
1. Configure the Multi Door station Mode for each Door station.
2. Enable the MDS function.
3. Configure the monitoring time for each Door station
ABCD
OUTIN
P-P+
A: input of the 1st doorstation
B: input of the 2nd doorstation
C: input of the 3rd doorstation
D: input of the 4th doorstation or input of the Slave C5-MDS.
OUT: output for the distributor.
IN: reserved.
P-: Power negative input. (Ground)
P+: Power positive input. (16~18V DC)
Video Entry System
---------------------------
[ 1 ] Configuration
* Back
Press 1 ~ 9 to select
---------------------------
- 9 . Default Set
- 8 .
- 6 . Camera Power On [ 0 ]
- 7 . Doorplate Mode [ 1 ]
- 5 . Intercom Video [ 1 ]
- 4 . Monitoring Nbrs [ 2 ]
- 3 . Unlock Timing [ 1 ]
- 1 . Net Address [001 ]
- 2 . [ ]Multi DS Mode 0
Change admin code
When the Door station is standby,
press [#8001] then input the
password [66666666], then you will
see Configuration menu. Press [2]
to enter the Multi DS Mode item,
then input the number for the Door
station and press [#] to save the
change, then press [*] to exit.
Set to 1 in the first door station, set
to 2 in the second door station, set
to 3 in the third door station, and so
on.
-15-

Video Entry System
---------------------------
[ 9 ] Advanced Config
*
Press 1 ~ 8 to select
---------------------------
- 1 . Tone Select[11]
- 2 . Image Memo [ 0 ]
- 3 . Voice Memo [ 0 ]
- 4 . Name List [ 1 ]
- 5 . HMC [ 2 ]
- 6 . Monitor Version [ 0 ]
- 7 . Call Mode [ 1 ]
- 8 . Language
- 9 . Timing [30]
Back
When the Door station is standby,
press [#8009] on the Door station
keypad, then input the password (the
default password is [66666666]),the
Advanced Configuration screen will
be displayed. Press [5] to enter the
Multi DS Mode item, then input [2]
and press [#] to enable the HMC
function, and the screen will back to
Advanced Config screen.
Video Entry System
>>[ 9 ][5 ]
*
HMC
( 0 ..4 )
－
# SaveBack
Video Entry System
>>[ 9 ][5].4 MR-MDS
*
Addr [ - ]
# SaveBack
Ch1T [--]
Ch2T [--]
Ch3T [--]
Ch4T [--]
When on the Advanced Config screen,
press [5] to enter the HMC item, press
[4] and then press [#] key to enter
the MR-MDS screen. The Addr item is
for the C5-MDS setting, if the current
Door station is connected to the
Master C5-MDS, set the Addr to [1], if
the current Door station is connected
to the Slave C5-MDS, set the Addr to
[2].
The Ch1T, Ch2T, Ch3T and Ch4T is for the monitoring time (seconds)setting for each port. .
If less than 4 door stations connected, set to [0] for the ports that are not used.
Note that all the Door stations which are connected to the same C5-MDS should be have
the same setting on the HMC item.
9.2 Enable the MDS function
9.3 Configure the monitoring time for each door station
-16-

C5-MDS
1st
doorstation
2nd
doorstation
3rd
doorstation
4th
doorstation
Monitor
Monitor
Monitor
Monitor
The switch should
be set to Master
C5-F4 Distributor
Connect to next C5-F4
ML-
L-
L+
L-
L+
ML+
PS2
P-
P+
ON
OFF
SW1
M
S
1
RF CARD
2 3
4 5 6
7 8 9
*0 #
1
RF CARD
2 3
4 5 6
7 8 9
*0 #
1
RF CARD
2 3
4 5 6
7 8 9
*0 #
1
RF CARD
2 3
4 5 6
7 8 9
*0 #
9.4 System Connection
-17-