Intelligent Home CAT-5 Series User manual

10
SPEAK
NOW
DOOR
SERVICE
OPEN
CALL
House Video Door Entry System
CAT-5 Series
Installation and User Manual
www.intelligenthomeonline.com
Manual covers all Genway models of CAT-5 Video monitors
and Door Stations

●Read this manual through before using the product.
●Slots or openings in the back of the monitor, are provided for ventilation
and to ensure reliable operation of the video monitor or equipment and
to protect if from overheating. These openings must not be blocked or
covered. The monitor should never be placed near or over a radiator or
heat register and should not be placed in a built-in installation such as a
bookcase unless proper ventilation is provided.
●All parts should be protected from violence vibration. Prevent impacts,
knocking and dropping.
●Clean the LCD monitor with Plastic Protection cleaner only.
●Image distortion may occur if the video door phone is mounted too close
to magnetic eld e. g. Microwaves, TV, computer etc.
●Please keep away the video door monitor from wet, high temperature,
dust, and caustic and oxidation gas in order to avoid any unpredictable
damage.
●Do NOT open the device in any condition, call the administrator for help
if there is any problem or mulfunction happens.
PRECAUTIONS

CONTENT
1. Video Monitors ----------------------------- 1
2. Doorbell Cameras- - - - - - - - - - - - - - - - - - - - - - - - - - - 3
3. Power Supply and Distributor ------------------ 5
4. System connections ------------------------- 6
5. Lock connections -------------------------- 12
6. Basic Video Door Phone Operation ------------- 14
7. Mute function ----------------------------- 15
8. Card Reader/Service Button (Doorbell Model B) ---- 15
9. Remote Control programming(Doorbell Model B) --- 16

145~160 cm
The recommended installation heights for both
Monitor and Camera 145~160mm.
Direct wall mounting Mounting with 86 box
Mute button
Reserved
Reserved
1.1 CYGNI Colour Monitor 7” brushed aluminium finish
1.2 LUNA Colour Monitor 7” Piano Black finish
1.3 VELA Colour Monitor 5” glass finish
Dimensions: W220xH150xD25mm
Full Duplex. Handsfree.
Resolution: 480 x 234 pixel
Ding-dong ringtone
Ring time: 30s; Talk time: 120s;
Monitoring time: 15s
Dimensions:W220xH150XD25mm
Full Duplex. Handsfree.
Resolution: 480 x 234 pixel
Ding-Dong ringtone
Ring time: 30s; Talk time: 120s;
Monitoring time: 15s
Dimensions: W220xH150xD25mm
Full Duplex. Handsfree.
Resolution: 320x 234 pixel
Ding-dong ringtone
Ring time: 30s; Talk time: 120s;
Monitoring time: 15s
1. Video Monitors
-1-

145~160 cm
The recommended installation heights for both
Monitor and Camera 145~160mm.
Note: Enure that RJ45
connector has enough
room behind the monitor
and is not under stress
1.4 JUNO Colour Monitor 3.5” in grey finish
1.6 Audio Phone for CAT5 series
1.5 Monitor mounting
1. Use the screws to x the mounting bracket on the wall;
2. Hang the Monitor on the mounting bracket rmly.
Audio phone can be connected instead of a video monitor.
You can combine audio phones and video monitors in one system. There is a
limit of four devices. For example, three video monitors and one audio phone;
or two video monitors and two audio phones.
Dimensions: W70xH215xD30mm
The audio phone has two functions, “Talk” and “Unlock”. Requires only two
wires of CAT5 cable terminated with RG45 connector into 4110S distributor.
Dimensions: W180xH120xD25mm
Full Duplex. Handsfree.
Resolution: 320 x 234 pixel
Ding-dong ringtone
Ring time: 30s; Talk time: 120s;
Monitoring time: 15s
Note: To disable the Alarm function
a) insert 9-pin plug into terminal on the rear of monitor
b) twist together (short) all 9 wires
-2-

Camera Lens
Call Button
Night-view LED
Speaker
Microphone
10
SPEAK
NOW
DOOR
SERVICE
OPEN
CALL
SPEAK
NOW
DOOR
SERVICE
OPEN
CALL
10
SPEAK
NOW
DOOR
SERVICE
OPEN
CALL
Camera Lens
Call Button
Service Button
plastic tag paper
Infrared LED
How to change name tag
Infrared Sensor
Speaker
Microphone
Door open LED
Speak Now LED
Card reader
&Name tag
10
2.1 Doorbell Camera Model A
2.2 Doorbell Camera Model B
2. Doorbell Cameras
-3-

How to adjust camera angle
Mounting with box
-4-

3.1 Power supply 4001
3.2 Distributor 4110s
3. Power Supply and Distributor
AC-DC Input: AC180V~270V 50~60Hz Output: DC35V 1,4A
Wall mount with screws supplied. Connect N L and Earth to the mains, connect GRN and DC+
according to diagram
Working Voltage DC30-35V
Working Current: <90mA
For star connection of up to a 4 video monitors/Audio telephones
Open sliding cover and set DIP switch number 1 into On position.
Power can be connected to either door station or 4110S distributor. If power supply connected to
4110S use DC+ for brown and GND for brown/white
Power Supply 4001
Mains input
DC output
GND
DC+
L
N
Distributor 4110S
ON DIP
LA LB VF- VF+ AF- AF+ GND DC+
to doorbell to monitors
-5-

4.1 Doorbell A single monitor connection
System requires CAT-5 or CAT-6 cabling and RG45 connectors (not supplied by default)
Working distance up to 100m with one power supply
Over 100m and up to 150m an additional power supply recommended.
Maximum number of video monitors or Audio handsets in one system: 4
Second door station can be added; requires additional LAN switch
4. System connections
Monitor
1 ~ 8
Note 1
Note 2 Note 3
Note 1: For distance over 50m, the doorbell needs to be connected to a 4001 power supply. Note 2: With single monitor systems, place jumper supplied into position shown. Note 3: This connector is for lock connection. See lock connection diagram.
Power supply
+
-
12345678
8. Brown 7. Brown/white 6. Green 5. Blue/white 4. Blue 3. Green/white 2. Orange 1. Orange/white
12345678
12345678
8. Brown 7. Brown/white 6. Green 5. Blue/white 4. Blue 3. Green/white 2. Orange 1. Orange/white
12345678
Power supply
Cat-5
Doorbell
Monitor
-6-

4.2 Doorbell B single monitor connection
Monitor
1 ~ 8
Brown
Brown/white
Blue
Blue/white
Green
Green/white
Orange
Orange/white
Note 1: Keep this jumper on for single monitor systems. Note 2: This connector is for lock connection. See lock connection diagram.
LA LB VF- VF+ VF- AF+ GND DC+
10
SPEAK
NOW
DOOR
SERVICE
OPEN
CALL
Note 1
Note 2
12345678
8. Brown 7. Brown/white 6. Green 5. Blue/white 4. Blue 3. Green/white 2. Orange 1. Orange/white
12345678
Power supply
+
-
Power supply
Cat-5
Doorbell
Doorbell back view
Monitor
-7-

4.3 Doorbell A multiple monitors connection
Doorbell
Camera
Power
Supply
Distributor 4110S
Distributor 4110S
Power
Supply 4# Monitor
1# Monitor
3# Monitor
2# Monitor
2# Monitor
4# Monitor
1# Monitor
3# Monitor
PORT4
DC+ GND AF+ AF- VF+ VF- LB LA
PORT3 PORT2 PORT1
+
-
Note 5
Note 1
Note 4
Note 2 Note 3
Note 1: For distance over 50m, the doorbell needs to be connected to a power supply. You can connect the power either from a 4001 power supply or 4110s distributor. Note 2: Remove the jumper for multiple-monitor systems. Note 5: Open the cover and set the DIP switch 1 to “On”.
12345678
8. Brown 7. Brown/white 6. Green 5. Blue/white 4. Blue 3. Green/white 2. Orange 1. Orange/white
12345678
Note 3: This connector is for lock connection. See lock connection diagram. Note 4: All RJ45 connectors have to be wired according to diagram.
-8-

4.4 Doorbell B Multiple monitors connection
Doorbell
Power
Supply
Distributor 4110S
Distributor 4110S
Power
Supply 4# Monitor
1# Monitor
3# Monitor
2# Monitor
2# Monitor
4# Monitor
1# Monitor
3# Monitor
PORT4
DC+ GND AF+ AF- VF+ VF- LB LA
PORT3 PORT2 PORT1
+
-
Brown
Brown/white
Blue
Blue/white
Green
Green/white
Orange
Orange/white
LA LB VF- VF+ VF- AF+ GND DC+
Note 4
Note 1
Note 1: Power to the doorbell can be connected either from 4001 power supply or 4110s distributor. Note 2: Remove the jumper for multiple monitor systems. Note 4: Open the cover and set the DIP switch 1 to “On”.
12345678
8. Brown 7. Brown/white 6. Green 5. Blue/white 4. Blue 3. Green/white 2. Orange 1. Orange/white
12345678
10
SPEAK
NOW
DOOR
SERVICE
OPEN
CALL
Note 2
Note 3
Doorbell back view
Note 3: This connector is for lock connection. See lock connection diagram.
-9-

4.5 Two Doorbell A multiple monitors connection
Power
Supply
Distributor 4230
1# Monitor
3# Monitor 2# Monitor
PORT3
Down linkUp link
Power
DC+ GND AF+ AF- VF+ VF- LB LA
PORT2 PORT1
doorbell2 doorbell1
DC+ GND AF+ AF- VF+ VF- LB LA PS GND DC+
+
-
Note 1
Note 3
Note 3
Note 2
12345678
8. Brown 7. Brown/white 6. Green 5. Blue/white 4. Blue 3. Green/white 2. Orange 1. Orange/white
12345678
2# Doorbell 1# Doorbell Distributor 4110S
Power
Supply 3# Monitor 2# Monitor 1# Monitor
Note 4
Note 1: For distance over 50m, the doorbell needs to be connected to a power supply. You can connect the power either from a 4001 power supply or 4110s distributor. Note 4: Open the cover and set the DIP switch 1 to “On”.
Note 3: This connector is for lock connection. See lock connection diagram. Note 2: All RJ45 connectors have to be wired according to diagram.
-10-

4.6 Two Doorbell B Multiple monitors connection
Power
Supply
Distributor 4230
1# Monitor
3# Monitor 2# Monitor
PORT3
Down linkUp link
Power
DC+ GND AF+ AF- VF+ VF- LB LA
PORT2 PORT1
doorbell2 doorbell1
DC+ GND AF+ AF- VF+ VF- LB LA PS GND DC+
+
-
Brown
Brown/white
Blue
Blue/white
Green
Green/white
Orange
Orange/white
LA LB VF- VF+ VF- AF+ GND DC+
Note 1
Note 1
Brown
Brown/white
Blue
Blue/white
Green
Green/white
Orange
Orange/white
LA LB VF- VF+ VF- AF+ GND DC+
Note 1: Power to the doorbell can be connected either from 4001 power supply or 4230 LAN switch. Note 2: Remove the jumper for multiple monitor systems.
12345678
8. Brown 7. Brown/white 6. Green 5. Blue/white 4. Blue 3. Green/white 2. Orange 1. Orange/white
12345678
Note 2
Doorbell back view
Note 2
Doorbell back view
Note 3
Note 3: This connector is for lock connection. See lock connection diagram.
-11-

4.7 Audio phone connection
5.1 Doorbell A lock connection
5. Lock connections
NONCCOM
NONCCOM
NONCCOM
+-
Note 1
Electric lock
Magnetic lock
Note 1: Reverse diode not used only for electric gate system.
Must be connected for all other locks.
Normal open connection
Normal open connection-2 locks
Normal closed connection
+-
Note 1
+-
Note 1
Electric lock
Doorbell Model A
-12-
Doorbell Distributor 4230
Power
Supply 1# Monitor
Audio phone Audio phone
2# Monitor
12345678
5. Blue/white
4. Green
12345678
Note: Connect 1 to 4th, 2 to 5th. No polarity

5.2 Doorbell B lock connection
GS INDOOR GND NO NC COM 12V OUT
+-
GS INDOOR GND NO NC COM
12V OUT
+-
GS INDOOR GND NO NC COM
12V OUT
+-
GS INDOOR GND NO NC COM
12V OUT
Note 1
Note 2
Note 2
Note 2
Electric lock
Electric lock
Magnetic lock
Electric lock
Electric lock
Note 2
Note 2
Note 1: Short COM and 12V OUT if lock doesn't have it's own power supply.
Note 2: Reverse diode not used only for electric gate system.
Must be connected for all other locks.
-13-

1. When a visitor presses the 'Call' button, the monitor rings and screen
shows the visitor.
2. Press Button to talk. If you choose not
to answer, the system will automatically
reset to standby after 60 seconds. Press
Button again to end the conversation; the
conversation will be cut off automatically after
120 seconds.
3. During ringing or talking, press Button to
unlock the door. (A Di~ sound will prompt to
indicate the door is opened)
4. In standby mode, press Button to monitor
outside. If two doorbells were installed,
pressing Button shows view of Doorbell 1,
press to end; press one more time to
view Doorbell 2. (Monitoring time is limited to
60 seconds)
6. Basic Video Door Phone Operation
-14-

SERVI
1. When you do not want to be disturbed
by any calling, you can turn on the mute
function.
2. Adjust the [Ring Volume
Adjustment] to the lowest, the ring will
be completely turned off, and the
indicator will be turned on.
●Card: Swipe any registered card on the card reader to release the door.
●Service/Trade Button: During the time specified for allowing trades-people or maids
access, press SERVICE button on the doorbell to release the door. This button is especially for
deliverymen or other service people. The function has to be programmed by the remote control.
See next section for remote control details.
7. Mute function
8. Card Reader/Service Button (Doorbell Model B)
Ring Volume Adjustment
Mute
indicator
-15-

Requires 2 x 1.5V AAA Batteries
(not supplied)
Working distance for programming
< 1m
9. Remote Control programming(Doorbell Model B)
9.1 Key panel discriptions
-16-

To be able to do programming, rst get into the programming mode.
9.2 Programming
9.2.1 Get into the system
-17-
1. Press (FN) + password (4 digits) + (ENTER). Note: default password is 1234
2. The door station will sound a long beep and DOOROPEN LED will flash slowly. You
have 7s to enter the password, otherwise system will exit automatically.
3. If wrong password was used the door station will say “Sorry, wrong number. Please try
again”. Repeat step 1 with correct password.
4. To exit programming mode, press (EXIT). Or system will exit automatically if no activity
in 2min.
5. During programming bell button and service button are not responsive.
1. Press FN + new password ( 4 digits) + repeat new password + ENTER
2. The door station will sound a long beep and DOOROPEN LED will ash slowly.
3. If you hear “Sorry, wrong number. Please try again” then repeat step 1
Note: Please memorize your new password. If you forget your new password please call
Distributor for help to reset a password
9.2.2 Change password