Intelligent Home DT-AKP User manual

User Manual
RF CARD
DT-ENG-AKP-V1 / 201701
• Pleasereadthismanualcarefullytoensuresafeandcorrectoperation.
• Keepthismanualwellforfuturereference.
DT-AKP
2 WIRE SYSTEM
Access keypad panel with scramble keypad

-1-
1.Parts and Functions
1
2
5
4
6
3
7
8
9
2.Terminal Descriptions
L2
EB+
EB-
NO
LK+
LK-
+12V
L1
BUS
SD Card Slot
CN-LK
[1] Front panel
[2] Touch sensitive digital
keypad
[3] LED1 indicator
[4] LED2 indicator
[5] LED3 indicator
[6] ID card window
[7] Mounting hook
[8] Connection port
[9] Screw hole
•SD Card Slot: To insert micro SD card.
•BUS: Connect to the bus line, non polarity.
•+12V: 12VDC power output.
•LK+: Common contact of the relay.
•LK-: Power ground.
•NO: Normally open contact of the relay.
•EB+: Exit button power(+) output.
•EB-: Exit button power(-) output.

-2-
3.Mounting
1 2
43
Use the screws to fix the mounting bracket to the wall.
Attach the panel to the mounting bracket. Use the screwdriver and the screw to fix the panel.
Connect the cable correctly.
4.Electric Lock Connection
4.1 Internal Power Supply Mode
Use the power of the system to supply for the electronic lock, so that the lock can be
connected to the access keypad panel directly, without an additional power supply for the
electronic lock. Note that the access keypad panel can only output 12Vdc power, therefore the
kind of lock is limited.

-3-
•The rated power of the lock must be less than 12Vdc 300mA when using internal power
supply mode.
•The GND must connect to the negative of the lock, and the COM connect to the positive .
•The default unlock time is 3s. If different unlocking time is needed to be configured,
change the Unlock Timing on access keypad panel.
12V 300mA
+
-+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
Set Unlock Relay mode
to Normally Open(0)
A. Connection for Power-on-to-Unlock type:
12V 300mA
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
+
-
Set Unlock Relay mode
to Normally Closed(1)
B. Connection for Power-off-to-Unlock type:
4.2 External Power Supply Mode
When the electronic lock is over 12 Vdc, external power supply for the lock is needed.
•The power supply for the lock must be less than 48Vdc 1.5A.
•The default unlock time is 3s. If different unlocking time is needed to be configured,
change the Unlock Timing on access keypad panel.
+
+
-
-
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
Set Unlock Relay mode to
Normally Open(0)
Note: Cut off this line when
using external power supply
C. Connection for Power-to-Unlock type:

-4-
+12V
LK - (GND)
LK+(COM)
N.O.
EB+
EB -
Set Unlock Relay mode to
Normally Closed(1)
+
+
-
-
Note: Cut off this line when
using external power supply
D. Connection for Power--off-to-Unlock type:
5. Functions Setup
This section explains the settings of each parameter,please refer to the following table:
About the setting mode:
Input the master code to enter the setting mode, and input the corresponding setting code to perform the settings
for the function you want. After settings have been made, input the following setting codes to continue the setting
operation. Press " " to exit the setting mode.
•The example is set as cancel button and # as conrm button, please refer to */# function
setting for detail information.
•Forbid sliding touch to the digital keypad, it may cause mistaken key, the correct operation is
using your nger to press the digital you desired.
• You should press“conrm”button after nish inputting the code number each time, otherwise,
the operation will be canceled automatically after 10s.

Order Setting items Setting code Setting range Default value
1 Reset all settings 00 -1,2,3,4
2 Set master code 01 1 ~ 12 digits
Valid keys:0 ~ 9 1234
3Set digitron display
mode(in standby mode) 02 Valid keys:0 ~ 2 0
5.1 Setting Items and Codes

-5-
4 Set unlock time 03 1 to 99 seconds 1 seconds
5 Set unlock mode 04 0:opened/1:closed opened
6Set touch key prompt
mode 05 0:ashing / 1: beep / 2:ashing + beep 2
7 Reset code settings 06 -1,2,3,4
8&# function settings 07 0:Normal/1:Reverse Normal
9 Tone select 08 0:Disable/1:Enable 1
10 Interference resistant
grade settings 09 Valid keys:0 ~ 5 3
11 Keyboard mode 10 0:standard / 1:scramble 1
12 Unlock work mode 11 Valid keys:0~3 0
13 Backup(master / user
card / password / tone) 12 -1,2,3,4
14 Update(master / user
card / password / tone) 13 -1,2,3,4
15 Device Address 14 Valid keys:0~3 0
16 RLC Control 15 Valid keys:0~4 0
17 Temporary(single use
only) password for relay1 18 Valid keys: 0 - 9 -
18 Temporary(single use
only) password for relay2 19 Valid keys: 0 - 9 -
19 Set the code for user
group 1 20-59 Valid keys: 0 - 9 -
20 Set the code for user
group 2 60-99 Valid keys: 0 - 9 -
21 Register [Manage card] 100 -1,2,3,4
22 Add user card 101 -1,2,3,4
23 Delete user card 102 -1,2,3,4
24 Format user card 103 -1,2,3,4

-6-
5.2 LED Indicator Denitions
5.3 Digitron Display Prompt
Indicator Status Description
LED1 Light on Release the rst/second lock
LED2
Light on Register [Add Manage card] / Add user card
Flash Register [Delete Manage card] / Delete user card
Double ash Format or Conguration switching of DT-ACC and ID card, it waits for
conrmation
LED3
Light on Setting code
Flash Setting value
Digitron display Prompt
OP1 Release the rst lock
OP2 Release the second lock
SUC Setting success
Err Password error / Non-access card
Err
1Setting code input error
Err
2Setting value input error
Err
3Cards have reached the number of rated
Err
4Input rule error

-7-
Err
5Wrong password 10 times in a row, is locked
Err
6Swipe invalid user card(When unlocking need swipe valid user card and password )
ACC The access control is congured for the DT-ACC application
ID The access control is congured for the ID card unlock application
S-A Register [Add Manage card]
S-D Register [Delete Manage card]
ADD Add user card
DEL Delete user card
CLE Format user card
BC1 Backup [Manage card]
BC2 Backup user card
BC3 Backup unlock password
BC4 Backup ringtones
UD1 Update [Manage card]
UD2 Update user card
UD3 Update unlock password
UD4 Update ringtones

-8-
Input the master code.
(Default: [ ] +[#] )
- All settings will restore to their
default value.
- The master code is allowed 1~12
digits,the same code cannot be set
for both the user code and the
master code,it is recommended
that you modify the default master
code.
- The unlock time can be set on
access keypad panel, and the
valid value is the number you set
last time.
(on)(off)(off)
LED1 LED2 LED3
Beep+, Beep
Beep+, Beep Beep+, Beep Beep+, Beep Beep+, Beep
Beep+
Inputting of value(ex.: 0)
range:0~2
Inputting of value (ex.: 09)
range:01~99
3.Set digitron
display mode
4.Set unlock time
(Default: 1s)
2.Set master code
(Default 1234)
Inputting of new master code
(ex.: 4321)(1~12 digits)
Input the setting code.
Inputting of code.
Input the setting code.
1.Reset all settings
00+#
1234+# 4321+#
01+#
0+# 09+#
Input the setting code.
02+#
Input the setting code.
03+#
- Digitron display mode:
0 : The scrolling display;
1 : All digitron display “-” sign;
2 : Only the upper left corner of the
digitron display “-” sign.
-
When the “ cancel” key is pressed, the indicator will show its standby color,
the buzzer beeps, and the system exits the setting mode.
- When there isn’t any operation within 10s, the indicator will show its standby color,
the buzzer beeps, and the system exits the setting mode.
Beep, Beep+
*
(flash)(off)(off)
LED1 LED2 LED3
(on)
(off)(off)
LED1 LED2 LED3
Beep+
(on)
(off)(off)
LED1 LED2 LED3
Beep+
(on)
(off)(off)
LED1 LED2 LED3
(off)
(off)(off)
LED1 LED2 LED3
Beep+
(on)
(off)(off)
LED1 LED2 LED3
(flash)(off)(off)
LED1 LED2 LED3
(flash)(off)(off)
LED1 LED2 LED3
(flssh)(off)(off)
LED1 LED2 LED3
5.4 Setting Steps

-9-
Input the master code.
(Default: [ ] +[#]) Beep+, Beep
7.Reset code setting 8. &# function setting6.Set touch key
prompt mode (Default Normal)(Default 0(opened))
Input the setting code.
Inputting of value
Input the setting code.
5.Set unlock mode
04+# 05+#
range:0:(open)/1:(close)
1+#
0/1 0/1
1+# 1+#1234+#
Input the setting code.
06+#
Input the setting code.
07+#
(ex.: 1)
Inputting of value Inputting of code Inputting of value
range:0~2
(ex.: 1)
range:0:(normal)/1:(reverse)
(ex.: 1)
*
*
*
- The unlock mode can be set on
access keypad panel, and the
valid value is the number you set
last time.
- Cancel all the passwords except
the master code.
- Restore the master code to
default value(1,2,3,4)
- When the item is set to 0, press
the button to cancel the input,
and press the # button to confirm
the input.
- When the item is set to 1, press
the # button to cancel the input,
and press the button to confirm
the input .
(on)(off)(off)
LED1 LED2 LED3
Beep+, Beep
(flash)(off)(off)
LED1 LED2 LED3
Beep+, Beep
(flash)(off)(off)
LED1 LED2 LED3
Beep+, Beep
(flash)(off)(off)
LED1 LED2 LED3
Beep+, Beep
(flash)(off)(off)
LED1 LED2 LED3
Beep+
(on)
(off)(off)
LED1 LED2 LED3
Beep+
(on)
(off)(off)
LED1 LED2 LED3
Beep+
(on)
(off)(off)
LED1 LED2 LED3
Beep+
(on)
(off)(off)
LED1 LED2 LED3
-
When the “ cancel” key is pressed, the indicator will show its standby color,
the buzzer beeps, and the system exits the setting mode.
- When there isn’t any operation within 10s, the indicator will show its standby color,
the buzzer beeps, and the system exits the setting mode.
Beep, Beep+
*
(off)
(off)(off)
LED1 LED2 LED3
- When it is set to 0, pressing the
touch key will blink one time.
- When it is set to 1, pressing the
touch key will sent out a sound of
beep.
- When it is set to 2, pressing the
touch key will blink one time and
sent out a sound of beep.