Intellinet IDC-757IR Manual

Network Mini Dome Camera
Hardware Installation Guide

Package Contents
Dome Camera IDC-757IR Outdoor Megapixel Night-Vision
Network Dome Camera
Quick Installation Guide Brief product information and quick
installation
Software CD
IP Surveillance Software Intelligent IP Installer
User Manuals
Language Packs
Accessories 6 pin terminal cable for DI/DO and audio
Screw pack for wall and ceiling mounting (2
screws, 2 plastic wall anchors)
Focus Adjustment
Drill Template
Hardware Description
Built-in Microphone Slide cover
Top cover
Dome bubble

Factory Reset
Reset: With the camera turned on, press the reset button briefly to reboot the camera,
or hold the reset button for 10 seconds to set all settings back to factory default values.
Mounting
hole
Routing hole
Focus Adjustment Ring
MicroSD/SDHC
Ethernet / PoE Connector
Reset Button Power LED Indicator
Network LED Indicator
External I/O connector
180°
mark

I/O Terminal Block
The Intellinet Network Camera provides an external I/O terminal block
which is used to connect input / output devices such as alarms or sensors.
The pin definitions are described below
PIN Definition Description Max. V/A
1 Ground -
2 + 5V DC 5V DC
0.5W
3 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -
4 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block
-
5 Digital Output
1
Uses an NPN transistor with the emitter connected to
the GND pin. If used with an external relay, a diode
must be connected in parallel with the load for
protection against voltage transients.
100 mA
24V
7 Digital Input 1 Connected to GND to activate, or leave floating (or
unconnected) to deactivate. 30V DC

LED Indicators
LED Color Indication
Network Blue Network activity is indicated by a flashing blue LED.
Power
Red Steady red during booting up process
Blue Turns blue upon completion of start-up
Purple Flashing during firmware upgrade
Unlit Off when press reset button is pressed
Hardware Installation
1) To open the camera housing use one hand to hold top cover and another hand to
push against the bottom of the camera housing.
2) Shift top cover to left (counter-clockwise) to open the dome cover. The cover will
not easily come off unless you apply a certain amount of force.

3) Attached the drill template to the wall. Drill three holes into the wall (two for
screws and one for the connection cable if you want to route cables through
conduit hole). Then push the supplied plastic anchors into the screw holes and
secure the plate with supplied screws.
4) Align the three holes on the base of camera with the two plastic anchors on the
wall or ceiling, insert the supplied screws to the corresponding hole and screw
them.
5) Adjust the angle of camera to aim the shooting area.

Lens Adjustment
WARNING:
DO NOT rotate the lens more than 360 degrees. Doing so will damage the camera lens module.

Rotate 360° Tilt 79°
Pan
344°

Cable Connections
Power over Ethernet (PoE)
Using a standard RJ-45 network cable, connect the dome camera to a
IEEE802.3af/at compliant PoE switch or PoE injector.
RJ-45 Cable
Due to the very compact housing dimensions, using a network cable with
a molded boot is not advisable. There is not enough room to connect the
RJ45 connector to the socket without bending the cable, which will likely
short the lifespan. We recommend using a network cable without a
modeled strain relief boot.
Accessing the camera
Start the IP Installer application to set up the camera. More information
can be found in the user manual on the installation CD.

INTELLINET NETWORK SOLUTIONS™ offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com
Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective
owners.