Intellinet IBC-667IR Manual

IBC-667IR
Network Bullet Camera
Hardware Installation Guide

Package Contents
Camera Network Bullet Camera
Quick Installation Guide Brief product information and quick
installation
Software CD
IP Surveillance Software Intelligent IP Installer
User Manuals
Language Packs
Accessories -Wall mount bracket & U-shape bracket
-Metal plate for wall mount bracket
-Alignment Sticker
-Waterproof Connector
-Screw pack for sun shield &
burglarproof screw
-Screw pack for wall and ceiling
mounting
-Silica gel
-Foam tape
-2 pin terminal blocks for power
-8 pin terminal blocks for DI/DO

Hardware Description
IRLED
Lens
LightSensor

I/O Terminal Block Circuit
I/O Terminal Block Pin Definition
PIN Definition Description Max. V/A
1 Ground -
2 + 12V DC 12V DC
1.2W
3 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -
4 AUDIO_Out(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -
5 Digital Output 1
Uses an NPN transistor with the emitter connected to the
GND pin. If used with an external relay, a diode must be
connected in parallel with the load for protection against
voltage transients.
100 mA
24V
6 Digital Output 2
Uses an NPN transistor with the emitter connected to the
GND pin. If used with an external relay, a diode must be
connected in parallel with the load for protection against
voltage transients.
100mA
24V
7 Digital Input 1 Connected to GND to activate, or leave floating (or
unconnected) to deactivate. 30V DC
8 Digital Input 2 Connected to GND to activate, or leave floating (or
unconnected) to deactivate. 30V DC
DigitalInput1/2:Max:30VDC
DigitalOutput1/2:Max:24V/100mA

LED Indicators
LED Color Indication
Network Green Active network link
Orange Flashing indicates network activity
Power
Red Steady red during boot-up process
Blue Steady blue when boot sequence has been completed
Unlit When the reset button was pressed for at least 5 sec.
and camera is restarting,
Micro SD / SDHC Orange Steady orange means SD card ready
Flashes orange while accessing SD card
Power Mode
PoE Mode
Power Requirement PoE (IEEE802.3af) with Class 3
Note: While IR on, Heater and Fan will be disabled.
Power Consumption 3.59 W, without IR/Heater/Fan
7.9 W, with max. IR on.
Adaptor Mode
Power Requirement 12V/1.5A Adaptor Note: While IR on, Heater or Fan would be activated
automatically.
Power Consumption
3.58 W, without IR/Heater/Fan
7.9 W, with max. IR on
9.6 W, with max. IR on / Heater on
8.87 W, with max. IR on / Heater Fan
Note: Heater will be activated while the inner temparature drops under 5C and fan over 50C.

Installing the hardware
1) Assembling sun shield and camera with two supplied screws(M3*6).
2) Fix U-shape bracket to the bottom of camera with supplied screws.
3) Insert all cables (RJ45/power cord/DIDO) into waterproof connector (M25*1.5).
4) Open the front cover and feed all cables through the screw hole of bottom cover from
outside. Connect them to sockets. Then secure the connector tightly.
5) Attach the foam tape and silica gel. (Please change a new silica gel if open the top
cover afterwards.)
6) Lock the front cover. Then secure the burglarproof screw.
7) Feed all cables through the front opening of wall mount bracket.
8) Push the spring mortise of wall mount bracket. Then hook the U-shape bracket onto
the groove of the former.
9) Secure the two screws of wall mount bracket on the other side.

Wall and Ceiling mounting
1) Attached the alignment sticker to the wall. Drill four holes into the wall. Three
holes are for the screws to affix the bracket to the wall, and one larger hole for
the cable. Push the supplied plastic anchors into the screw holes and secure the
plate with the supplied screws (T1/4”*32).
2) Fix the wall mount bracket to the plate with the supplier screws.
3) Position the camera angle by adjusting the pan and tilt.
Lens Focusing

Factory Reset
Reset: With the camera turned on, press the reset button briefly to reboot the camera,
or hold the reset button for 10 seconds to set all settings back to factory default values.
1. Connect the camera via PoE
Using a standard RJ-45 network cable, connect the bullet camera to an
IEEE802.3af/at compliant PoE switch or PoE injector.
2. Connect the camera without PoE
1. Connect the power adaptor to the dome camera
2. Using a standard RJ-45 network cable, connect the camera to a normal
Ethernet Switch or Router
3. Software Installation
Insert the Installation CD into a CD or DVD drive and follow the instructions given
by the Quick Installation Guide.

INTELLINET NETWORK SOLUTIONS™ offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com
Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective
owners.