Intercoax ECP-2808RM User manual

User Manual
version 1.7
Ethernet over Coax / UTP Managed Receiving Switch
ECP-2808RM / ECP-2816RM / EUP-2808RM / EUP-2816RM
Network Solution Provider
High-Speed, Long distance Ethernet and PoE Extender

Network Solution Provider
High-Speed, Long distance Ethernet and PoE Extender
Contents
Precaution and Safety Guidelines
1. Product Overview
2. Hardware Installation
3. Product Specifications
4. Management Software Configuration
5. Troubleshooting
6. Warranty Policy
7. Regulatory and Certificates
8. Customer supports
1 - 1. Introduction
1 - 2. Features
1 - 3. Package Contents
2 - 1. Front Panel
2 - 2. Rear Panel
2 - 3. LED Indication
2 - 4. Configuration Instruction
2 - 4 - 1. Prepare devices and materials
2 - 4 - 2. Hardware installation
2 - 4 - 3. Joining instruction
2 - 4 - 4. Label the configured network group
2 - 5. Transmission distance & Bandwidth by distance
2 - 6. Typical Installation
3 - 1. Technical Specifications
4 - 1. Overview
4 - 2. System Requirements
4 - 3. Getting started
4 - 3 - 1. ECP MANAGER LITE
4 - 3 - 2. ECP MANAGER
4 - 4. Configuration Windows
4 - 4 - 1. System Summary
4 - 4 - 2. General Window
4 - 4 - 2 - 1. Easy View
4 - 4 - 2 - 2. List View
4 - 4 - 2 - 3. Receiver Overview
4 - 4 - 2 - 4. Join & Node Control
4 - 4 - 2 - 5. Node Monitor
4 - 4 - 2 - 6. Power
4 - 4 - 2 - 7. Multicast
4 - 4 - 2 - 8. Settings
4 - 4 - 3. ECP Config Window
4 - 4 - 3 - 1. Group Configuration
4 - 4 - 3 - 2. ECP Configuration
4 - 4 - 4. SNMP Window
4 - 4 - 5. Admin Window
4 - 4 - 5 - 1. Administrator
4 - 4 - 5 - 2. System Config
4 - 4 - 6. Logout Window
5 - 1. Hardware
5 - 2. Software
17
18
21
39
41
3
4
5
6
7
8
13
15
16
40

Network Solution ProviderPage 03 of 41
High-Speed, Long distance Ethernet and PoE Extender
Precaution and Safety Guidelines
• Please install the device following the installation guide.
• Reed all warnings.
• Warning - Do not touch the device and cable with wet hands.
• Warning - Clean this apparatus only with a dry cloth.
• Warning - Please do not put the products on anything electrical conductive (screwdrivers, coins, iron, etc.)
and not put them around water.
• Warning - Do not install near any heat sources such as radiators, heat registers, stoves
or other apparatus that produce heat.
• Warning - Do not use for other purposes.
• Warning - Do not put the signal lines (Coax, UTP) in the same conduit as high voltage wiring
• Do not put any sticker or paint on it.
• Indoor use only.
• Please use only attachments or accessories specified by the manufacturer.
• Unplug the device during a lightning storm or when the device is not used for a long time.
(i. e. Connecting analog camera to BNC connector)
• Do not connect analog cameras to BNC connectors(B-Linx Port) on this devices (ECP Series only)
• Do not connect any IP devices to RJ45 connectors (T-Linx Port) on this devices (EUP Series only)
• When the unit is not working properly, please contact dealer or customer service.
• Please do not disassemble the unit by yourself.
• If this device emits smoke, abnormal noise, or a strange odor, please turn off
the power switch, unplug the AC power cord immediately, and contact dealer or customer service.
The lightning flash with arrowhead symbol within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.

Network Solution ProviderPage 04 of 41
High-Speed, Long distance Ethernet and PoE Extender
1. Product Overview
1-1. Introduction
The All-New Intercoax ECP/EUP-2808RM/2816RM Series is 19” rack mountable managed Long Distance Ethernet
and PoE over Coax/UTP Receiving Switches.
ECP/EUP-2808RM/2816RM series are capable of connecting more than 8/16 ECP Transmitters even
with Daisy-Chain connection and also support PoE powered devices such as IP cameras.
Data rates up to 1Gbps are achievable, making these devices the ideal choice in new or legacy installations
where existing Coax/UTP cable is re-deployed as part of an upgrade from Analog to IP cameras.
ECP/EUP-2808RM series have built-in 320 Watt power supply and ECP/EUP-2816RM series
have built-in 640 Watt power supply (*Dual power supply of 320W + 320W for power sharing and redundancy)
PoE up to 60W per port is available.
Browser based GUI manages all connected IEEE1901-HPAV standard devices.
Furthermore, the world first innovative “Intercoax ECP Manager”software allows managing multiple
of ECP/EUP-2808RM/2816RM series remotely from the central management office
• Ethernet & PoE transmission over Coax / UTP cable
• Complies to IEEE1901-HPAV standard
• Extended transmission distance up to 2,400m
• PoE/ PoE+/ Extra PoE up to 60W (PoE++) per B-Linx port & T-Linx port
• Total management software, “Intercoax ECP Manager", supported
• Friendly Graphic User Interface with EasyView
• Remote Join & Unjoin, Change joining password
• Remote power reset by each port
• Real-time monitoring of power consumption for each port
• Multicast Setting with IGMP Query & Report Generator
• SNMP ready
• VLAN ready
• Port Locking for for extra secured network connectivity
• Alarm LED & buzzer and notification on ECP Manager
• Scheduled event reporting and alert reporting to designative users
• Back up & Restore of configuration
• Auto Power Short Protection
• B-Linx & T-Linx Smart Device Detection for safe power transmission
• 320W (8 port) / 640W (16 port) Built-in Power Supply
• Built-in crosstalk canceling technology
• Support multiple configuration (Daisy Chain, Star, Ring, Etc.) on each port
• Gigabit SFP and Copper uplink port
• 19-inch(1U) rack mountable design
1-2. Features
1-3. Package Contents
Bracket
AC Power code
ECP-2816RM
(ECP-2808RM / EUP-2808RM / EUP-2816RM) Quick Installation Guide

2
4
3
56 7 8
56 7 8
56 7 8
1
2
15 6
3
3
3
4
4
4
7 8
Network Solution ProviderPage 05 of 41
High-Speed, Long distance Ethernet and PoE Extender
2. Hardware Installation
2-1. Front Panel
EUP-2816RM
ECP-2816RM
EUP-2808RM
ECP-2808RM
1. B-Linx Ports (1~8 / 1~16) :
Connect Intercoax ECP Transmitters or IEEE1901-HPAV standard devices by coaxial cable with BNC male connector.
2. T-Linx Ports (1~8 / 1~16) :
Connect Intercoax ECP Transmitters or IEEE1901-HPAV standard devices by UTP cable with RJ45 male connector.
3. Smart B-Linx / T-Linx Detection On <-> Off :
B –Linx / T-Linx Detection mode On/Off switch
Detection Mode ON: Detects B-Linx & T-Linx devices before supplying power over Coax.
Detection mode OFF: By-pass detection, classification and power management checks
[Caution]
Do not connect analog cameras or network devices on BNC or RJ-45 port directly if Smart
B-Linx / T-Linx detection switch is OFF, it may cause a serious damage to the device connected.

Network Solution ProviderPage 06 of 41
High-Speed, Long distance Ethernet and PoE Extender
2
INPUT: 100~240VAC 50/60 Hz 5A
Model : ECP-2816RM
Default IP : 192.168.4.17
Intercoax Co., Ltd
www.intercoax.com
MAC Address #1
MAC Address #3
H/W Version 1.01
MAC Address #2
MAC Address #4
Serial Number
4. Join (1-4, 5-8, 9-12, 13-16) :
Hidden button to create new Network group with ECP Transmitters
- Press the button with a paper clip and hold for 2 seconds for Joining (Create new password)
- Press the button with a paper clip and hold for 15 seconds for Unjoining (Remove the existing password)
※Please note the joining instruction on Page 11
5. Buzzer On <-> Off :
Move the switch left or right to buzzer sound on or off.
6. Factory Reset :
The hidden factory reset button
Press and hold for 10 seconds the reset button to restore to its original factory settings.
7. SFP :
Connect an SFP module for uplink data (1000 Base-FX GBIC slot)
8. Link :
Connect an RJ45 Ethernet cable for uplink data (10/100/1000 BaseT)
2-2. Rear Panel
1. Power ON/OFF Switch
2. Power Connector
The connector is for 100~240V AC power inputs 50Hz/60Hz
1

Network Solution ProviderPage 07 of 41
High-Speed, Long distance Ethernet and PoE Extender
2-3. LED Indication
EUP-2816RM
2
ECP-2816RM
213 4 6
5
3 4 6
5
EUP-2808RM
2
ECP-2808RM
213 4 6
5
3 4 6
5
NO
1
2
3
4
5
- Short circuit or over current
protection is working
- ECP/EUP
transmitter linked properly
- Transmitting Data Via Coax / UTP
- Factory reset is progressing
Blinking
- Transmitting Data
Green: 10/100
Amber: 1000
- No device connected
on B-Linx / T-Linx port
- Unjoined ECP device is connected
- Device in normal operation
- SFP Link is down
- No device connected on SFP port
Off
- Uplink (Copper) is down
- Power OFF
6
B-Linx / T-Linx
(1~8 / 1~16)
Join
(1~4 / 5~8,
9~12, 13~16)
Alarm
SFP Link
LED Indication
LINK
PWR
On
- ECP/EUP Transmitter is connected
- Power over coax / UTP
working properly
- System boot-up
- Alarm is detected
- Transmitting Data
- Power ON
•
•
•
•

Network Solution ProviderPage 08 of 41
High-Speed, Long distance Ethernet and PoE Extender
2-4. Configuration Instruction
2-4-1. Prepare devices and materials
• Ethernet over Coax /UTP Receiving Switch (ECP-2808RM, EUP-2808RM, ECP-2816RM, EUP-2816RM)
• ECP-Transmitters (ECP-2801, ECP-2701, ECP-9501, ECP-8401, ECP-8301, EUP-2801, EUP-8401,etc)
• EUP-Transmitters (EUP-8401T, EUP-2601T, EUP-2801T & All ECP-Transmitters with BTE-02)
• RJ-45 patch cord
• Short Coax cable or 4 pairs UTP cable (at least 4 cables for joining)
• Password label (if it is necessary)
• Paper clip (If it is necessary for pressing joining button)
• Network Switch and PC (OS: Window 7 or later)
2-4-2. Hardware Installation
1. Apply power to the receiving switch
2. Use short coax or UTP cables to connect the receiving switch and the ECP/EUP-Transmitters
3. The blue power LED and B-Linx & T-Linx LED of the receiving switch will be ON.
4. The blue power LED of the ECP/EUP-Transmitters will be ON.

Network Solution ProviderPage 09 of 41
High-Speed, Long distance Ethernet and PoE Extender
5. The green join LED of the receiving switch and ECP-Transmitters will blink regularly if both devices are already joined
with same network password.
6. If the green Join LED is OFF on both receiving switch and ECP-Transmitter, joining work should be necessary
for network communication.
7. Connect ECP-Transmitters to IP Camera
( IP it is PoE IP Camera, Please select PoE Switch ‘ON’ from ECP Transmitters)
8. Connect the receiving switch to Network switch and PC using RJ45 Patch cord.
[Note]
All ECP/EUP products have the same network password as factory default mode
to support plug & play configuration between ECP/EUP Series.
[Note]
For joining work, please refer to the joining instructions on page 11.

Network Solution ProviderPage 10 of 41
High-Speed, Long distance Ethernet and PoE Extender
Rackmount Bracket Installation Guide
1. Remove the 3 of factory installed screws from both sides of managed switch and keep these screws
as they will be used to attach the new rack mount brackets. (See Picture 1 & 2)
2. Using these screws, attach the supplied rackmount bracket to the managed switch (Carefully check LEFT
and RIGHT side brackets, see pictures 3 & 4).
Rack Mount Instructions
1. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature
of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an environment compatible
with the maximum ambient temperature (Tma) specified by the manufacturer.
2. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of airflow required
for safe operation of the equipment is not compromised.
3. Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not
achieved due to uneven mechanical loading.
4. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit
and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Picture 1 Picture 2
Picture 3 Picture 4

Network Solution ProviderPage 11 of 41
High-Speed, Long distance Ethernet and PoE Extender
2-4-3. Joining instruction
Group A Group B Group C Group D
• All ECP/EUP products are pre-joined with the same network password (“HomePlugAV”) as the factory default mode
to support plug & play configuration between ECP/EUP Series.
• If the receiving switch and all of ECP/EUP-Transmitters are already Joined (Join LED on both devices),
It is unnecessary to join the devices again pressing JOIN button.
(In this case, please use the exclusive software, “ECP Manager” or “ECP Manager Lite” to join the new devices)
• ECP/EUP-28XXRM series have 2 or 4 network groups with every 4 channels (1-4, 5-8, 9-12, 13-16)
and It is possible to avoid network interference by setting the password of each group.
1. Basic connection
Prepare 4 short coaxial cables for convenience and connect each ECP/EUP-Transmitters
to Group A (B-Linx port 1 to 4) and apply the power to the receiving switch.
2. Unjoin (If required, when Join LED on both receiving switch and ECP-Transmitter is not ON)
Removing the password
A. Push the join button for 15 seconds on each unit of ECP/EUP-Transmitter in Group A.
B. ECP/EUP-Transmitter will reboot and it is ready to be joined.
C. BNC Join LED turns off.
3. Join (Recommend to join by ECP Manager software) :
Creating new password
A. After unjoining, press the Group A join button and hold for 2 seconds and release the button.
B. Press the join button on one of ECP/EUP-Transmitters and hold for 2 seconds and release the button.
PWR LED turns off and on, and then BNC Join LED turns on and will be flickering and it means
both devices are joined successfully.
C. Join other 3 units of ECP/EUP-Transmitters repeating above steps (A, B)

Network Solution ProviderPage 12 of 41
High-Speed, Long distance Ethernet and PoE Extender
4. Repeat above ①~ ③steps for the other groups (B, C, D)
[Caution]
After joining work with Join button, a new and random password is automatically assigned
and it can not be restored to the factory default password.
[Note]
Joining can also be made with the exclusive management software, INTERCOAX ECP MANAGER
but before joining with software, the ECP-28XXRM series and ECP-Transmitters should already be
joined together with the same network group password. (For more details about software joining,
please refer to software setting page)
2-4-4. Label the configured network group
• After joining with the join button, it is highly recommended to put the label on the devices joined
in same network group and keep the documentation of Group ID and MAC address of the devices in each group.
• After joining with the software, it is highly recommended to put the label on the devices joined in same group
and password of the group and keep the documentation of Group ID and MAC address of the devices in each group.
• This documentation helps to identify each network group after deployment and when maintaining devices.
[Note]
Password on ECP/EUP-Transmitters can be also easily changed by Intercoax Manager software.
Please visit www.intercoax.com to download the software.

Network Solution ProviderPage 13 of 41
High-Speed, Long distance Ethernet and PoE Extender
2-5. Transmission distance & Bandwidth by distance
2-5-1. Performance chart
■ ECP-2808RM / ECP-2816RM (B-Linx Models)
• When using ECP-2XXX series as Transmitter (Based on One transmitter per port)
• When using ECP-9xxxx & 8xxxx series as Transmitter (Based on One transmitter per port)
RG6 Coaxial Cable
Trans. Rate (Mbps)
PoE Output (W)
50m
21.2
45.2
100m
21.2
33.1
200m
21.1
18.2
300m
21.1
12.5
500m
21
7.4
RG6 Coaxial Cable
Trans. Rate (Mbps)
PoE Output (W)
50m
57.5
45.3
100m
57.5
33.1
200m
57.5
18.4
300m
57.5
12.1
500m
50
6.9
* Above performance charts may vary depending on cable spec and installation environment.
Max. Transmission rate (Mbps) / meter
0
10
20
30
40
50
60
70
50m 100m 200m 300m 500m
ECP-2701
ECP-2601
ECP-9501
ECP-8401
ECP-8301
Max. PoE Output (Watt) / meter
0
10
20
30
40
50
50m 100m 200m 300m 500m
ECP-2701
ECP-2601
ECP-9501
ECP-8401
ECP-8301

Network Solution ProviderPage 14 of 41
High-Speed, Long distance Ethernet and PoE Extender
2-5. Transmission distance & Bandwidth by distance
2-5-1. Performance chart
■ EUP-2808RM / EUP-2816RM (T-Linx Models)
• When using 2xxx series + BTE-02 (ECP Model only) as Transmitter as Transmitter
(Based on One transmitter per port)
• When using ECP/EUP-9xxxx & 8xxx series (ECP Models must have BTE-02) as Transmitter
(Based on One transmitter per port)
Cat.5e UTP Cable
Trans. Rate (Mbps)
PoE Output (W)
50m
21.2
51.7
100m
21.2
45.4
200m
21.1
28.1
300m
22.2
21.3
500m
20.2
12.6
Cat.5e UTP Cable
Trans. Rate (Mbps)
PoE Output (W)
50m
55.1
51.6
100m
51.7
45.5
200m
35.4
28.4
300m
25.7
21.4
500m
23.8
12.6
* Above performance charts may vary depending on cable spec and installation environment.
Max. Transmission rate (Mbps) / meter
0
10
20
30
40
50
60
50m 100m 200m 300m 500m
ECP-2701
ECP-2601
ECP-2801
EUP-2801
ECP-9501
ECP-8401
EUP-8401
ECP-8301
Max. PoE Output (Watt) / meter
0
10
20
30
40
50
60
50m 100m 200m 300m 500m
ECP-2701
ECP-2601
ECP-2801
EUP-2801
ECP-9501
ECP-8401
EUP-8401
ECP-8301

ECP-2816RM
EoC
PoC
PoE Camera
ECP-2704T
Coax
PoE
Data
AC 100~240V
AC 100~240V
NVR Network Switch
ECP-2701
Coax
Coax
Coax
ECP-2701
ECP-2701
ECP-2701
PoE Camera
PoE
Data
EUP-2816RM
EoC
PoC
ECP-2704T
Cat.5e or Better
ECP-2701
BTE-02
BTE-02
Cat.5e or Better
EUP-2601T
Cat.5e or Better
EUP-8401T
Cat.5e or Better
NVR Network Switch
Network Solution ProviderPage 15 of 41
High-Speed, Long distance Ethernet and PoE Extender
2-6. Typical Installation
• The ECP/EUP-2808/2816RM Series deliver high bandwidth and power over coax/UTP cable.
All ECP/EUP single port units or ECP/EUP transmitter series can be used as remote transmitters,
typically located at the IP camera.
• ECP/EUP-2xxxx series are recommended to be used as remote transmitters for the maximum performance.
Application Examples
48V~56VDC Ethernet
PoE-PWR
Data-Link
Join-Link
PowerON
Join
PoE
OFF-ON
EUP-8401 EthernetoverCoax Transceiver

Model ECP-2808RM EUP-2808RM ECP-2816RM EUP-2816RM
IGMP (V1/V2/V3) Snooping, IGMP Query & Report Generator
Coax
Up-Link 1 x RJ45 - 10/100/1,000 Base-T with Auto MDIX, 1 x SFP - 1,000 Base-T
AC100V~240V (50Hz/60Hz), 320W
Max DC 56V, 1.07A (60W per port for PoE support)
Auto Detecon & Protecon
UP to 560Mbps Full Duples UP to 1Gbps Full Duples
B-Linx / T-Linx Transmission Rate
(Ethernet over Coax/UTP)
Interface
441.5(L) x 349(W) x 44(H)mm
CE (including Railways Standard EN 50121-4), FCC, KC, UL
IEC61000-4-5 4kV(1.2 / 50us), 2kA(8/20us)
Compliance
Mechanical
Power
0C ~ +60C
-30C ~ +80C
10% ~ 80%
Environment
IEEE1901-HPAV
OFDM
up to 2 remote converters per port recommended (Max up to 4 per port)
Available
B-Linx / T-Linx Communicaon Standard
B-Linx / T-Linx Communicaon Modulaon
B-Linx / T-Linx Communicaon
Mulple Nodes (Daisy Chain)
ECP Manager Connecvity
IGMP
Blue
Buzzer / Mute
128-bit AES
Green (10/100-Link) / Yellow (1,000-Link)
Green
Green (1,000-Link)
Red
Green
Buzzer
LED Indicaon
Power
RJ45 Up-Link
SFP Up-Link
Channel
Join
Alarm
Event
Encrypon
Smart B-Linx / T-Linx Device Detecon
4,650g 4,600g 5,090g 5,030g
Up to 1,200m (RG6 / 7W)
Up to 3,000m (Cat.5e)
Coax
UTP
Up to 2,300m (RG6)
Up to 1,200m (Cat.5e)
Up to 1,500m (Cat.5e / 7W)
Data Transmission
Distance
Power Transmission
Distance
Coax
UTP
DC output per Port
AC Input
Port Short Protecon
Surge Protecon
Cerficaon
Weight
Dimension
Storage Temp
Operang Temp
Relave Humidity
UTP
8 * 75Ω BNC (Female) -
Ethernet over Coax (B-Linx)
8 * 100Ω RJ45 (Female) -
Ethernet over Twisted Pairs (T-LinX)
16 * 75Ω BNC (Female) -
Ethernet over Coax (B-Linx)
16 * 100Ω RJ45 (Female) -
Ethernet over Twisted Pairs (T-LinX)
Detecon On / Off
441.5(L) x 340(W) x 44(H)mm 441.5(L) x 349(W) x 44(H)mm 441.5(L) x 340(W) x 44(H)mm
Network Solution ProviderPage 16 of 41
High-Speed, Long distance Ethernet and PoE Extender
3. Product Specifications
3-1. Technical Specifications
3-2. Regulatory Certifications

Network Solution ProviderPage 17 of 41
High-Speed, Long distance Ethernet and PoE Extender
4. Management Software Configuration
4-1. Overview
ECP MANAGER LITE & ECP MANAGER
• The ECP MANAGER LITE is the browser based GUI. Users can access to management of all ECP-2808/16 series
and its connected IEEE1901-HPAV standard transmitters.
• The ECP MANAGER software allows managing multiple of INTERCOAX Managed Receivers remotely from
the central management office. With the ECP MANAGER software, users can access to all connected
IEEE1901-HPAV standard transmitters.
• Various additional features are available with the ECP Manager and ECP Manager Lite as below;
Remote monitoring for ECP devices & End or remote (usually Tx models) device connection
Remote transceiver Joining (Network Grouping)
IP addressing for managed EoC Switch
System reboot
Power reset by each port
Real time Monitoring for power consumption by each port
Real time Monitoring for total power consumption
Port locking for extra secured network connectivity
Multicast setting with IGMP Query Generation
Scheduled event reporting and alert reporting to designative users
SNMP Setting
Firmware upgrade for managed EoC Switch
VLAN Setting
Configuration backup & Restore
4-2. System Requirements
• Recommended Operating System for ECP Manager : Window 7 or Higher version
• Recommended Version of Internet Explorer for ECP Manager Lite : Window 8 or Higher version
• Internet connectivity : During initial installation for ECP manager, Internet connectivity is required.

Network Solution ProviderPage 18 of 41
High-Speed, Long distance Ethernet and PoE Extender
4-3. Getting started
4-3-1. ECP MANAGER LITE
1. Under network setting, set your PC’s IP address to 192.168.4.xxx and subnet mask to 255.255.255.0.
2. Open the web browser and enter http://192.168.4.17, the factory default IP address of the ECP Managed Switch.
3. Login window will be opened on web browser.
4. Enter the default User ID, "admin"
5. Enter the default Password, "admin"
6. Open the Setting page and change IP address as desired address.
7. Change Login ID and Password on Admin page of the Intercoax ECP Manager.
[Note] Please refer to Admin page for changing Admin ID and password (Page 36)

Network Solution ProviderPage 19 of 41
High-Speed, Long distance Ethernet and PoE Extender
4-3. Getting started
4-3-2. ECP MANAGER
1. Unzip the file, ECPManager.zip
2. Move the unzipped folder, ECPManager to Local Disk (C:) => Location: C:\ECPManager
3. Click the setup.exe file
[Note] During initial Installation for ECP Manager. Internet connectivity is required.
4. Click the Install button on Application Install – Security Warning window.
5. Installation procedure will be done.
6. Start ECP Manager software.
7. Default Login ID: admin
Default Login Password: admin

Network Solution ProviderPage 20 of 41
High-Speed, Long distance Ethernet and PoE Extender
4-3. Getting started
4-3-2. ECP MANAGER
8. Change the Login ID and Password as desired on the Admin window.
[Note] Please refer to admin window page for changing ID and Password (Page 36)
9. Create a group on Group Configuration tab of ECP Config Window.
[Note] Please refer to Group configuration window for creating Group (Page 33)
10. Add new ECP managed switch on ECP Configuration tab of ECP Config Window.
[Note]
- Please refer to ECP configuration window for adding New ECP managed switch (Page 34)
- When adding ECP managed switch, please Enter the default IP, 192.168.4.17.
11. IF new ECP managed switch is added correctly, O.K message will be shown on the Current ECP Manager
Reporting Status of the System summary and the background color of the device ID will be changed to green
12. Change the IP address as desired on the Setting menu of the General Window.
[Note] Please refer to Setting menu on General window (Page 31)