Interlogix AP633A User manual

AP633A Passive Infrared Detector Installation
Instructions
Description
The AP633A offers the detection of motion for infrared targets
in selectable ranges extending 40 feet (12.2m), 80 feet
(24.4m), and 200 feet (61.0m). The viewing angle selection
allows the installer to select and delete any portion of the
coverage pattern to customize the optical performance of the
unit. The mounting plate of the unit is equipped with precise
adjustment screws to allow the installer to alter the horizontal
viewing point as much as 2 degrees to the left or right, up or
down. Features include:
• Step focus curtain
• Calibrated sensitivity
• Coverage up to 200-foot (61.0m) max.
• 12 different protection patterns
• Precision step focus mirror optics
• Form C contacts
Mounting tips
• Do not mount the unit outdoors.
• Do not block the viewing angle of the unit.
• Mount the unit so that would-be intruders cross the pattern
of detection at a 90 degree angle.
• Seal all openings and wire entries.
• When mounting the unit on masonry surfaces, use an
appropriate moisture barrier.
• Use of the vertical screw adjustment may reduce the unit’s
range.
• Avoid these sources of disturbance:
• Sunlight or vehicle headlights shining directly onto the
unit.
• Heat sources or mobiles in the field of view.
• Strong air drafts blowing onto the unit.
• Animals in the field of view.
• Insects in the housing or on the face of the unit.
• Rapid temperature changes in the field of view.
• Very strong sources of RF energy and induction of
electrical noise.
Installing the unit
1. Loosen the screw at the bottom of the unit; then remove
the front housing (Figure 1 below).
Caution: You must be free of static electricity before handling
sensor circuit boards. Touch a grounded, bare metal surface
before touching circuit boards or wear a grounding strap.
Figure 1: AP633A
2. Pull down on the plastic locking tab at the base of the
circuit board to remove the mirror/circuit board assembly.
See Figure 2 on page 2.
3. Remove the appropriate wiring knockouts and pull the
cable through the entries. See Figure 3 on page 2.
4. Level the backplate to the wall leaving a 1/2 inch
clearance space above the unit. For flat-wall mounting,
use the four mounting holes. For corner mounting
applications remove the mounting knockouts located in
each corner. See Figure 3 on page 2. Insert 8-32 x 2 inch
screws. Tighten until secure, but be careful not to over-
tighten the backplate as you may need to adjust the
viewing angle after walk testing.
5. Replace the mirror/circuit board assembly then make wire
connections. See Figure 4 on page 2.
P/N 1036522 • REV C • 19JUN12 1

6. Set the sensitivity and test the zone locations. See
Figure 5 below, “Setting the sensitivity” on page 3, and
“Testing zone locations” on page 3.
7. Replace the front housing and tighten the screw located at
the unit base.
8. Conduct a final walktest by walking across the unit’s field
of view - but not directly at the unit.
Figure 2: Locking tab
Locking tab
Figure 3: Mounting and wiring
Wire Routing
Knockouts
Corner
Mounting
Knockout
Corner
Mounting
Knockout
Mounting Holes
Corner
Mounting
Knockout
Corner
Mounting
Knockout
Mounting Holes
Surface Mount Wire Knockouts
Wire Routing
Knockouts
Optional
Swivel Bracket
Mount
Primary Wire
Entry
Knockout
Figure 4: Terminals
33ohm
1 2 3 4 5 6 7 8
NEG +12V
Alarm Tamper
Spare
Terminal AP633A
#1 (-) Negative
#2 (+) Positive
#3 Closed Loop Contact
#4 Common
#5 Open Loop Contact
#6 Tamper Closed Loop
#7 Tamper Closed Loop
#8 Spare (not used)
Aiming the unit
To ensure proper coverage, make subtle pattern adjustments
using the three adjustment screws located inside the unit (see
Figure 5 below):
•The top screw adjusts the unit’s coverage pattern up or
down.
• The bottom two screws adjust the coverage pattern to the
right or left.
Figure 5: Adjustments and jumpers
Viewing Angle Adjustment
Jumper D
(LED)
Jumper A
(Sensitivity)
Jumper B
(Test) Tamper
10468
C
B
A
2
Viewing Angle Adjustment
Terminals
Setting the sensitivity
Select the sensitivity setting that best meets the needs of a
given application by changing Jumper A (see Figure 5 on
2 AP633A Passive Infrared Detector Installation Instructions

Note: Be certain to carefully locate field of view for required
detection. As with all PIR units, there is no detection between
fields of view. Installation must be tested one or more times
yearly.
page 2). The unit is factory set in the increased sensitivity
mode.
Standard Sensitivity - All 40-foot-wide
(12.2m) applications (left, right, or full). Use
with patterns E, G and H only. See Figure 7.
Increased Sensitivity - 80-foot-wide
(24.4m) angle areas, 40-foot (12.2m) curtain
only or long-range applications. Use with
patterns A through L. See Figure 7.
High Sensitivity - Use only in hazard-free, high-
securityapplications.Usewithpatterns Athrough
L. See Figure 7.
Setting the LED
Use Jumper D to enable/disable the LED. The LED is factory
set in the enabled mode. See Figure 5 on page 2.
elbasiDDELelbanEDEL
Optional swivel bracket
Note: The unit ships with the 200-foot (61.0m) plastic mask
(marked "6") insert in place. The 40-foot (12.2m) center curtain
is always enabled to ensure undercrawl detection. For special applications, an optional swivel bracket is available
see Figure 6 below.
Testing zone locations Figure 6: Optional swivel bracket
The test feature allows you to identify each zone of coverage
and avoid “splitting” a zone of coverage between two areas
with dissimilar infrared energy levels, such as a metal door and
a freezer. Jumper B is factory set with the test mode disabled
(see Figure 5 on page 2). To test the zone locations:
1. Insert Jumper B so that both pins are covered.
2. Without stopping, walk across the coverage
pattern and watch the unit. Each time you
enter a zone, the green LED illuminates.
When the green LED goes out, you are in the
center of a zone or between two zones.
3. After identifying each zone location, return
the unit to normal mode by inserting Jumper
B on only one pin so that the two pins are not
connected.
Test - On
Test - Off
AP633A Passive Infrared Detector Installation Instructions 3

Coverage patterns
Figure 7: Coverage patterns
2
3
1
4
12
4
3
12
4
5
6
3
12
4
6
3
AC
F
D
G
IJL
B
EH
K
40 ft. 80 ft. 200 ft.
(12.2m)(24.4m)(61.0m)
1
4
5
6
3
40 ft. 80 ft.
(12.2m) (24.4m)
40 ft. 80 ft.
(12.2m) (24.4m)
6
2
6
3
40 ft. 80 ft.
(12.2m) (24.4m)
40 ft.
(12.2m)
40 ft.
(12.2m)
40 ft. 80 ft. 200 ft.
(12.2m)(24.4m)(61.0m)
4
5
6
3
2
4
5
6
3
40 ft.
(12.2m)
40 ft. 80 ft. 200 ft.
(12.2m)(24.4m)(61.0m)
1
4
6
40 ft. 80 ft.
(12.2m) (24.4m)
40 ft.
(12.2m)
40 ft. 80 ft. 200 ft.
(12.2m)(24.4m)(61.0m)
1 - Removes Right 40 ft.(12.2m), Wide Angle Pattern
2 - Removes Left 40 ft.(12.2m), Wide Angle Pattern
3 - Removes Left 80 ft.(24.4m), Wide Angle Pattern
4 - Removes Right 80 ft.(24.4m), Wide Angle Pattern
5 - Removes 80 ft. (24.4m), Center Pattern Only
6 - Removes 200 ft.(61.0m), Long Range Pattern Only
(Right - Left, as viewed from the detector.)
12
4
6
35
Specifications
Input power 9.5-15 VDC
Peak to peak ripple 2V max. (@ 12V)
Current consumption 25mA average (normal operation, LED
enabled), 40mA max.
Contact rating Alarm - 100mA @ 28 VDC with 33 ohm
resistor in series
Tamper - 100mA @ 28 VDC
Coverage pattern 12 selectable patterns using snap-on
blockers
Mounting height 6' to 10' (1.8m to 3.0m)
Operating temperature 0°F to 131°F (-18°C to 55°C)
Dimensions 6.3" x 4.1" x 3.0" (16.0cm x 10.4cm x 7.6cm)
Regulatory information
Listings UL 639
Ordering information
Part # Electrical configuration Comments
AP633A Form C, SPDT (closed or
open loop) 40', 80' Wide Angle and 200' Long Range, Passive Infrared
Motion Sensor
BR601 Wall Mount Swivel Bracket
The unit is to be connected to a UL Listed power supply or control unit
capable of providing a minimum 4 hours of standby power. The
equipment should be installed in accordance with NFPA 70. The unit
should be tested at least once a year.
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.interlogix.com/customer-
support
Copyright © 2012 UTC Fire & Security. All rights reserved.
4 AP633A Passive Infrared Detector Installation Instructions