Intermec 6220 Use and care manual

6220 Hand-Held Computer
TECHNICAL REFERENCE
"""""""""""""""""""""
P/N 977-054-010
Revision D
December 2000

" NOTICE The information contained herein is proprietary and is provided solely for the purpose of allowing customers to
operate and service Intermec manufactured equipment and is not to be released, reproduced, or used for any
other purpose without written permission of Intermec.
Disclaimer of Warranties. The sample source code included in this document is presented for reference only.
The code does not necessarily represent complete, tested programs. The code is provided AS IS WITH ALL
FAULTS." ALL WARRANTIES ARE EXPRESSLY DISCLAIMED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
We welcome your comments concerning this publication. Although every effort has been made to keep it free of
errors, some may occur. When reporting a specific problem, please describe it briefly and include the book title
and part number, as well as the paragraph or figure number and the page number.
end your comments to:
Intermec Technologies Corporation
Publications Department
550 econd treet E
Cedar Rapids, IA 52401
ANTARE , INTERMEC, NORAND, NOR*WARE, PEN*KEY, ROUTEPOWER, TRAKKER, and TRAKKER
ANTARE are registered trademarks and ENTERPRI E WIRELE LAN, INCA, Mobile Framework, TE 2000,
UAP, and UNIVER AL ACCE POINT are trademarks of Intermec Technologies Corporation.
 1999 Intermec Technologies Corporation. All rights reserved.
Acknowledgments
ActiveX, Microsoft, MS, and MSĆDOS, Windows, and Windows NT are registered trademarks and MSDN, Visu l
B sic, Visu l C++, and Windows for Pen are trademarks of Microsoft Corporation.
AS/400, IBM, IBM PC, Micro Ch nnel, PS/2, and OS/2 are registered trademarks and AIX and Present tion
M n ger are trademarks of International Business Machines Corporation.
Intel is a registered trademark of Intel Corporation.
S nDisk is a trademark of anDisk Corporation.
XEROX is a registered trademark of Xerox Corporation.
XMS is a registered trademark of Lotus, Intel, Microsoft, and A T Research.

6220 Hand-Held Computer Technical Reference i
CONTENTS
""""""""""""""""""""
SECTION 1
Introduction
About this Manual 1Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction to the 6220 Computer 1Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Batteries 1Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Battery 1Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backup Battery 1Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Check 1Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectors 1Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display 1Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backlight 1Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Touch creen 1Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Docks and Chargers 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard Remapping 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
uspend/Resume 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CMO 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ystem Memory (DRAM) 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash ROM 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Cards 1Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open ystem Environment 1Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ports 1Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management 1Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printers 1Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Processor 1Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset witch 1Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
canners 1Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ystem BIO 1Ć7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Publications 1Ć7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer upport 1Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Factory ervice 1Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customer upport Center 1Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Web ite 1Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulletin Board ervice 1Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2
DOS Device Drivers
APM Clock Driver 2Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BGI upport 2Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using N6220.BGI Driver 2Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bitmap Text Output 2Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BGI Demonstration Files 2Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CONTENTS
ii 6220 Hand-Held Computer Technical Reference
DO Utilities 2Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Utility 2Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remapping Keyboard 2Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Power Management 2Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using C400CFG 2Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Create Download Include File 2Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Mapping Utility 2Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File Integrity Verification Utility 2Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Get or et ROM DO Boot Flags 2Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multipurpose Delay Utility 2Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset the ystem 2Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RAM Drive 2Ć7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IrDA Printer 2Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAN Communications 2Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NPCP Printer 2Ć9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation and Configuration 2Ć9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required CONFIG. Y Entry 2Ć9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required AUTOEXEC.BAT or CONFIG. Y Entry 2Ć9. . . . . . . . . . . . . . . . . . .
Functionality and Usage 2Ć10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Card ervices 2Ć11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pen Calibration 2Ć12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration 2Ć12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required Calibration Files 2Ć12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 2Ć12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pen Driver 2Ć13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PenPrint 2Ć13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation and Configuration 2Ć13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Codes 2Ć14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Usage Notes 2Ć14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management 2Ć15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
creen Emulation 2Ć16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Line witches 2Ć16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Font File Format 2Ć16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupts upported by FONTMAP.EXE 2Ć17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unsupported 4000 eries Video Interrupts 2Ć17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tethered canner 2Ć18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation and Configuration 2Ć18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Usage 2Ć18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Line witches 2Ć19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Memory Provider 2Ć20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3
Converting Applications
Converting to the 6000 eries Computers 3Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Files No Longer upported 3Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changed Files 3Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
New 6000 eries Files 3Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unchanged Files 3Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4000 eries Programming Interfaces 3Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation and Configuration 3Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Line witches 3Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CONTENTS
6220 Hand-Held Computer Technical Reference iii
SECTION 4
System Information
Binary Image Files Posted to Bulletin Board 4Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash Release Contents 4Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NonĆEthernet 6220FL2A 4Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet 6220FL2B 4Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating Flash Using an Application oftĆDownload 4Ć2. . . . . . . . . . . . . . . . . . . . . . . .
Prerequisites 4Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure 4Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating Flash using INTERLNK 4Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prerequisites 4Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure 4Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating Flash Using an ATA Card 4Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prerequisites 4Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure to Build an ATA Card 4Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure to Reflash with an ATA Card 4Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Updating Flash Using a 4 MB RAM Card 4Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prerequisites 4Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure to Build IFL RAM Card 4Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure to Reflash with an IFL Card 4Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Methods 4Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Partial Flash Download 4Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATA Boot Card 4Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RAM Boot Card 4Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full Flash Download 4Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5
Communications
Using INTERLNK and INTER VR 5Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Norand Utilities 5Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial Program Load 5Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NPCP Network 5Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRInet 5Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TFTP 5Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TTY 5Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling Norand Utilities from Application 5Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ystem etup Requirements 5Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NPCP 5Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TTY 5Ć3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRInet Using P ROM0C Version 3.xx 5Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRInet Using P ROM0C Version 2.xx 5Ć4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valid Control File Parameters 5Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upload Control File Parameters 5Ć7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communications Log File 5Ć8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protocol Errors 5Ć9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCOM ession 5Ć12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ession Control File 5Ć12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Download Request File 5Ć12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upload and Download Files 5Ć13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PL/N File Descriptor for Binary Files 5Ć14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CONTENTS
iv 6220 Hand-Held Computer Technical Reference
FIGURES
Figure 1Ć1 HandĆHeld Computers (front view) 1Ć2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1Ć2 Main Battery Pack (bottom view) howing Contacts 1Ć3. . . . . . . . . . . . . . .
Figure 1Ć3 Location of Components (rear, top) 1Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 1Ć4 Location of Components (top end) 1Ć6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2Ć1 Power Management oftware 2Ć15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLES
Table 2Ć1 MMBFLAG.COM Error Levels 2Ć5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2Ć2 FONTMAP Interrupts upported 2Ć17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 4Ć1 6220FL2A BB Equivalents 4Ć1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5Ć1 NPCP Protocol Errors 5Ć9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5Ć2 MININET Protocol Errors 5Ć9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5Ć3 NRInet Protocol Errors 5Ć10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5Ć4 TTY Protocol Errors 5Ć11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GLOSSARY
INDEX

6220 Hand-Held Computer Technical Reference 1-1
Section 1
Introduction
""""""""""""""""""""
This publication contains information for developing applications for the
PEN*KEYE 6220 HandĆHeld Computer from Intermec Technologies Corporation.
The majority of this book is for experienced application programmers. However,
developing applications for this computer should be similar to developing DO
applications for any standard PC.
About this Manual
This manual contains the following sections.
"Sectio 1 Ċ I troductio
Provides technical information about the 6220 Computer, related publicaĆ
tions, and customer service information.
"Sectio 2 Ċ DOS Device Drivers
Contains installation and configuration information for DO device drivers,
including communications and DO Utilities.
"Sectio 3 Ċ Co verti g Applicatio s
Details information applicable for converting 4000 eries applications for
use on a 6000 eries Computer.
"Sectio 4 Ċ System I formatio
Defines system information included with the 6220 Computer.
"Sectio 5 Ċ Commu icatio s
Describes communications supported for this computer.
Introduction to the 6220 Computer
The 6220 Computer has a number of features that are useful in the mobile sysĆ
tems marketplace, such as:
"Lithium ion smart battery for fullĆday battery life.
"Power managed for longer battery life.
"Compatible with existing Intermec docks, chargers, printers, and other peĆ
ripherals.
"Optional touch screen for signature capture.
"Backlit display.

SECTION 1Introduction
1-2 6220 Hand-Held Computer Technical Reference
Figure 1Ć1 shows a front view of each of the two models.
30-KeyModel56-Key Model
Figure 1Ć1
Hand-Held Computers (front view)
From the viewpoint of an application, the 6220 Computer is like other PC compaĆ
tibles, with a few exceptions, as described in the following paragraphs.
Batteries
BCAUTION: This computer has ONE primary power source, the MAIN Battery. The Backup Battery
maintains power to RAM while changing Main Batteries. At all times during operation
and while stored (overnight, long periods of time, and during suspend), the unit must
have its Main Battery installed.
Main Battery
The main battery is a 1350 mAH lithium ion power pack, and has a useful life of
500 charge/discharge cycles. The battery pack contains a smart processor for the
system software to report battery status.
In suspend mode, the main battery maintains RAM, RTC, and CMO settings.
When the computer is off charge, the main battery also supplies needed charge
to the backup battery. The main battery must always be installed, except when
replacing batteries.
Be sure the batteries are fully charged before leaving them off charge for long
periods of time. A unit, with fully charged main and backup batteries, can be
left off charge overnight or for a long weekend. However, if the computer goes
into shutdown mode as a result of a low main battery, data remains protected by
the backup battery.
Backup Battery
The backup battery has a small nickelĆcadmium (NiCd) battery and is on trickleĆ
charge when the unit is powered from the main battery or connected to a charĆ
ger. It is unable to maintain DRAM contents for an extended time, with the exĆ
pectation of supporting the system without a main battery. If the main battery
is drained completely or is not reinstalled, DRAM data is lost. When fully
charged, the backup battery retains data in the DRAM for about ten hours.

SECTION 1 Introduction
6220 Hand-Held Computer Technical Reference 1-3
Battery Check
Check the main battery capacity by touching two contacts at the same time, as
shown in Figure 1Ć2. Another method if checking the battery is to use a software
fuel gauge based on the APM 1.1 specification.
Capacityis displayed from
right to left. The higher the
capacity the more LEDs light.
one LED = less than 25% capacity;
two LEDs = 25–50% capacity;
three LEDs = 50–75% capacity;
four LEDs = more than 75%
= LED on
= LED off
1
2
Touch finger across
first two contacts
Figure 1Ć2
Main Battery Pack (bottom view) Showing Contacts
Connectors
There are connectors on both ends of the 6220 Computer:
"A 15Ćpin serial port, mounted on the top end.
"An RJĆ11 4Ćpin phone jack, mounted on the top end.
"A 12Ćpin surface contact connector, mounted on the bottom end, and makes
contact with a dock.
Display
This terminal features a backlight, with (optional) touchĆsensitive LCD display
and a resolution of 160 (wide) by 200 (long) pixels. Use a stylus or your finger on
the touch screen. Do not use a ball point pen, since it may damage the screen.
Application software can only operate the display in portrait mode and receives
touch inputs as standard mouse messages.
Backlight
The backlight is useful in darkened conditions. However, use the backlight only
as needed, since it reduces the battery life.
The amount of time the backlight stays on before shutting off is controlled
through the Configuration Program, C400CFG.COM. ee page 2Ć2 for more
information.
Touch Screen
The (optional) overlay resistive analog touch screen is controlled by a single chip
touch screen controller. The touch screen controller provides x,y point informaĆ
tion to the CPU whenever a touch is detected on the screen.

SECTION 1Introduction
1-4 6220 Hand-Held Computer Technical Reference
Docks and Chargers
The batteries in the 6220 Computer can be charged by placing the computer into
a dock or connecting the batteries to a charger. The 6220 Computer fits many of
the docks available for other handĆheld computers. The following types of docks
are available for the 6220 Computer:
"Si gle Dock Integrated AC power supply, holds one handĆheld computer
"Multidock Integrated AC power supply, holds up to eight handĆheld comĆ
puters, secure storage, light status indicator.
"Pri ter Intermec ACĆpowered printers generally provide a way to put a
handĆheld computer in a dock and charge it while docked.
"Wall Charger
Keyboard
The 6220 Computers have two keyboard configurations, 30Ćkey or 56Ćkey, as
shown in Figure 1Ć1 on page 1Ć2.
Keyboard Remapping
All keys can be remapped, including shifted and unshifted keys, with the excepĆ
tion of the ON key (suspend/resume) and the Yellow shift key. Use
C400CFG.COM to remap the keypad, as described on page 2Ć2.
Suspend/Resume
To suspend operation, press and release the ON key. To resume operation, press
and release the same key.
The 6220 Computer automatically suspends when there is no activity for a time,
which conserves power, thereby protecting against loss of data while replacing
the main battery or leaving the unit unattended. The time before automatically
suspending is determined by the configuration program.
Memory
The following types of memory are available with this computer:
CMOS
CMO memory retains configuration information (such as RAM drive parameĆ
ters across reset cycles).
System Memory (DRAM)
The 6220 Computer supports 8 and 16 MB of DRAM memory which is ordered at
the time the product is purchased. The computer can be upgraded to a larger
memory size if Customer upport Center installs a new memory board.
Flash ROM
The 6220 Computer has 2 MB of fieldĆprogrammable flash memory, with BIO
and DO firmware. Applications stored in flash memory are copied into DRAM
for execution. Flash memory does not require a battery to maintain its contents.
PC Cards
Use either a Type II card or Type III card in this computer. These cards work
similar to a hard drive on a PC. Modems, radios, hard drives, and other options
will also be supported as they become available. When inserting a PC Card into
the drive, use the slot closest to the display.

SECTION 1 Introduction
6220 Hand-Held Computer Technical Reference 1-5
Different brands of PC cards can be used in the 6220 Computer. Memory cards
are available in a variety of sizes and types. Check with your Intermec Account
Executive for specific options.
"NOTE: SRAM cards are not supported as data storage devices on this computer.
Figure 1Ć3 shows a rear view of the 6220 Computer, with the display facing
down. Insert the card into the drive closest to the display. After inserting a boot
card into a Type II slot, press the reset button before the card is recognized.
1. PC memory compartment door (removed).
2. Lower PC Card slot for Type II or Type III cards.
3. PC Card.
4. Upper PC Card slot for Type II or Type III cards.
3
4
1
2
Figure 1Ć3
Location of Components (rear, top)
"NOTE: Cards that conform to the PC Card interface standard (new standard), or the PCMCIA inter-
face standard (old standard), are referred to as: “PC Card” or “PC Card xxxxx” (where xxxxx
consists of “modem,” “drive,” or other device type). This is because “PC Card” is rapidly be-
coming the accepted industry term for a storage medium that conforms to these standards.
Open System Environment
One of the major benefits of an openĆsystem approach is that development equipĆ
ment and software can be acquired from many different vendors, including InterĆ
mec Technologies Corporation. This provides a wide latitude in selecting the
equipment and software tools that are best suited to particular needs.
Ports
The 6220 Computer contains a variety of ports, which include:
"Two serial ports (standard COM1 and multiplexed COM2), with connecĆ
tions through the dock, using CMO logic levels.
"An Infrared port for wireless communication with peripherals.

SECTION 1Introduction
1-6 6220 Hand-Held Computer Technical Reference
Power Management
Advanced Power Management (APM) software coordinates powerĆsaving operaĆ
tions between applications and hardware. The APM code detects periods of inacĆ
tivity and lowers power consumption by progressively reducing the processor
clock speed, shutting down unused components, and finally suspending the unit.
The APM software is responsible for handling suspend/resume requests via the
ON key and notifies the system software when suspend/resume events occur.
The processor, the LCD screen, PC Cards, and the tethered scanner are compoĆ
nents that are automatically powerĆmanaged.
Device drivers and applications can dynamically modify APM behavior through
APM function calls, or certain configuration files can be modified to establish a
default power management.
Printers
Tethered and IrDA printing are supported. NorandR Portable Communications
Protocol (NPCP) printing is supported only if the NPCP printing toolkit is used.
Processor
The 6220 Computer is based on the Élan C400 processor operating at a maxiĆ
mum speed of 99 MHz. This processor is modeled after the AMD Am486 CPU
and contains an 8 KB writeĆback cache, integrated memory controller, PC/AT
system logic, PC Card controller, LCD graphics controller, IrDA infrared port,
and power management features in one integrated package. The integrated
LCD controller is CGA register set compatible.
Reset Switch
Occasionally, the 6220 Computer needs to be reset. Note th t uns ved d t will
be lost when this occurs. To reset the unit, push a small diameter wire, such as a
paper clip, into a hole in one end of the 15Ćpin serial connector (as in Figure 1Ć4).
1. Reset switch
2. 15-pin serial connector
3. Phone jack (optional)
4. Display side of computer
2
3
4
1
Figure 1Ć4
Location of Components (top end)
Scanners
The tethered scanner connects to the standard 15Ćpin serial connector located on
the top end of the terminal. R Ć232 is used for data transfer. Intermec TechnolĆ
ogies Corporation provides device drivers for all supported operating systems.

SECTION 1 Introduction
6220 Hand-Held Computer Technical Reference 1-7
System BIOS
The 6220 BIO is an implementation of the PC compatible BIO with added feaĆ
tures specific to INTERMECR handĆheld computers.
ystem BIO performs powerĆon tests, system configuration, lowĆlevel power
management, and runĆtime realĆmode interrupt service handling. During the
powerĆon sequence, the BIO performs a Power On elf Test (PO T), which
checks all system components and configures them in preparation for booting the
operating system. The system then boots the operating system from an flash
memory.
ystem BIO storage is provided by flash memory which is field programmable.
The BIO may occasionally need updating. ee ection 4 for details.
Related Publications
The publications listed below contain additional information relating to the 6220
Computer or publications that may be good references for application developĆ
ment. Order Intermec publications from an Account Executive.
"6220 HandĆHeld Computer User's Guide Intermec P/N: 961Ć028Ć104
"APM BIOS Interfa e Spe ifi ation 1.1
Intel Corporation
Literature Distribution Center
P.O. Box 7641
Mt. Prospect, IL 60056Ć7641
(800) 548Ć4725
Publication Order Number: 241704Ć001
"Handwriter Re ognition System for Windows User's Guide
Communication Intelligence Corp. (CIC) Intermec P/N: 961Ć054Ć001
"Handwriter Re ognition System for Windows Release Notes
Communication Intelligence Corp. (CIC) Intermec P/N: 961Ć054Ć002
"Handwriting Re ognition System, HRĆ1200, User Manual
ynaptics Intermec P/N: 961Ć054Ć007
"Mi rosoft Developers CD
A technical reference for developers; published quarterly on CD:
Microsoft Developers Network
One Microsoft Way
Redmond, WA 98052Ć6399
"System BIOS for IBM PC's, Compatibles, and EISA Computers,
Se ond Edition
Phoenix Technologies LTD.
AddisonĆWesley Publishing Company
I BN: 0Ć201Ć57760Ć7
"Writing TCOM Modules in PL/N
Intermec Technologies Corporation P/N: 541Ć002Ć523
"PL/N 4000 Series Manual, Volume 1 Intermec P/N: 977Ć037Ć007
"PL/N 4000 Series Manual, Volume 2 Intermec P/N: 977Ć037Ć008

SECTION 1Introduction
1-8 6220 Hand-Held Computer Technical Reference
Customer Support
Factory Service
If your unit is faulty, you can ship it to the nearest authorized ervice Center for
factoryĆquality service.
Customer Support Center
The Intermec Customer upport Center (technical support) telephone number is
800Ć755Ć5505 (U. .A. or Canada) or 425Ć356Ć1799. The facsimile number is
425Ć356Ć1688. Email is [email protected].
If you email or fax a problem or question include the following information in
your message: your name, your company name and address, phone number and
email to respond to, and problem description or question (the more specific, the
better). If the equipment was purchased through a ValueĆAdded Reseller please
include that information.
Web Site
The Customer upport File Libraries, including Hot Tips and Product Awareness
Bulletins, are available via the Intermec Product upport page at this URL:
http://norbbs.nor nd.com/index.htm. New users can sign up for a new account
on this page.
PDF versions of Intermec manuals can be found at this URL:
http://corp.intermec.com/m nu ls/english.htm.
Bulletin Board Service
The Customer upport Bulletin Board (BB ), maintained by Intermec TechnoloĆ
gies Corporation, provides software and documentation:
"Pho e umber: 319Ć369Ć3515 (14.4 Kbps modem)
319Ć369Ć3516 (28.8 Kbps modem)
"Protocol: Full duplex, AN I or AN IĆBB ; 300 to 28,800 bps; v.32bis; 8
bits, no parity, 1 stop bit. For highĆspeed modems, dis ble XON/XOFF nd
en ble RTS/CTS.
This is the same location available via the web site. If your web access uses
highĆspeed phone lines, the web interface provides a faster response.

6220 Hand-Held Computer Technical Reference 2-1
Section 2
DOS Device Drivers
""""""""""""""""""""
This section contains installation and configuration information for the following
DO device drivers, including communications device drivers and DO utilities.
APM Clock Driver
CLOCK.EXE is part of the Advanced Power Management (APM) system when
running under DO . CLOCK is a device driver that replaces the standard DO
clock driver. It must be installed as a device driver at system startup time.
Besides the normal clock driver functions, CLOCK makes sure that the date and
time are maintained during suspends. It forces a read from the CMO realĆtime
clock upon Resume.
CLOCK is installed as a device driver in the CONFIG. Y file. CLOCK should
be installed after NORDO PM.EXE. A typical entry in CONFIG. Y to install
CLOCK is:
DEVICE=NORDOSPM.EXE
DEVICE=CLOCK.EXE
After installation, CLOCK displays the following message:
CLOCK.EXE Vn.nn DOS APM Clock Driver
There are no installation switches or userĆprogrammable parameters for
CLOCK.EXE.
BGI Support
N6220.BGI is a custom Borland Graphics Interface (BGI) realĆmode
PENKEY.BGI driver, located in the DO Toolkit. It develops Borland
graphicsĆbased applications for this display. One use in a DO application is to
separate the application and the BGI driver. This requires loading the driver
from your application. The calls are documented in the Borland C++ DO
Reference book. tart with inst lluserdriver. This is also used by CALIB.EXE
(Pen Calibration).
Using N6220.BGI Driver
The driver plugs in" to the Borland BGI graphics library via the
inst lluserdriver() function. Mode selection is performed through several custom
user drivers provided in the BGI demo CU TOM.C file.
"NOTE: The N6220.BGI driver can be initialized and closed many times during a program run, but call
installuserdriver( ) once and save the value returned for subsequent driver initializations.

SECTION 2DOS Device Drivers
2-2 6220 Hand-Held Computer Technical Reference
Bitmap Text Output
The Borland BGI drivers do not fill the background color when rendering the bitĆ
map font, thus erasing the text before writing over it. Use the b r( ) function to
erase (clear) the text area (text cannot be written over with new text or spaces).
N6220.BGI fills the bitmap text background, eliminating text erasure gyrations.
This new text mode is set using the BGI setwritemode() function and passing the
BGI_NIFTYTEXT constant (defined in N6220.H). Pass BGI_NORMALTEXT to
the setwritemode() function to return to normal BGI text rendering.
BGI Demonstration Files
If the BGIDEMO.C demo file is copied and modified for personal needs, copy othĆ
er files included with #include lines found in the demo file.
Refer to Borl nd C++ DOS Reference for additional information.
DOS Utilities
Configuration Utility
C400CFG.COM provides configuration for timers, activity monitors, keypad,
and features such as: standby, powerfail, enable/disable suspend key, processor
slowdown percent, system clock slowdown rate.
Remapping Keyboard
All keys on the keyboard, including the shifted and unshifted keys, can be reĆ
mapped, except the ON key (suspend/resume) and the shift key.
"NOTE: Before reprogramming certain keys, consider the effect it might have on other operations.
For example, remapping the shifted [7] and [8] keys on a 30-key keyboard would lose the
contrast adjustment.
ConfiguringPower Management
APM software is implemented to coordinate powerĆsaving operations between
applications and the hardware.
Using SC400CFG
Use C400CFG.COM to reconfigure any part of the system, such as the keypad
or power management. The example C400CFG.INI file lists all the parameters
that can be reconfigured.
First, make a copy of the example C400CFG.INI file (located in the \Utils diĆ
rectory on the boot drive). The name of the INI copy can be changed.
The copy should include only those parameters that are to be changed. Delete
all others. After modifying the configuration file, add the following line to the
AUTOEXEC.BAT file on the PC Card, then reboot. Usage is as follows:
sc400cfg.com [options]
If your configuration file has a different name, specify that name in the comĆ
mand line, as described later in the Comm nd Line Switches paragraph. This
paragraph also contains other details concerning the [options]. If an INI file is
not specified, C400CFG.INI (if available) is used as the default.

SECTION 2 DOS Device Drivers
6220 Hand-Held Computer Technical Reference 2-3
SC400CFG.COM <options>
where <options> include the following:
ć? Displays a help list similar to that shown here.
ćF <file ame>
pecifies file with setting changes. Default = C400CFG.INI
ćS<sectio >
pecifies section in file to use.
EXAMPLE: SC400CFG –F:MyConfig.ini –S:NewConfigs
where MyConfig.ini is the name of your configuration file and the [NewConfigs]
section of the configuration file contains the applicable settings.
Omitting the ćF parameter defaults to the default configuration filename,
C400CFG.INI.
Omitting the ćS parameter tells C400CFG.COM to use the [Def ult] section of
the configuration file.
Create Download Include File
Given a list of files, IPLFMT.EXE creates a download include file by concatenatĆ
ing a list of initial program files to be loaded onto a handĆheld computer, prefixĆ
ing each file with an appropriate DO FIL header. ee page 5Ć14 for header deĆ
scriptions. Use the following format to create a network download file.
iplfmt.exe <list file> <include file>
list file
The name of the file that contains a list of files to include.
in lude file
The name of the download include file, such as DOWNLOAD.INC (this
file is created by IPLFMT.EXE)
IPLFMT.EXE also extracts files from a network download file, using this format:
iplfmt.exe –r <include file> [<path>]
in lude file
The name of the download include file, such as DOWNLOAD.INC (this
file is read by IPLFMT.EXE).
path The name of the output directory where the files are to be extracted; this
parameter is optional.
A download list file contains the names of the files to be sent to your handĆheld
computer. Each line in the file specifies one name. The file names may include
path information so that all of the files need not be in the same directory on the
host. However, the file is transmitted without the source path information, and
placed in the current directory of your handĆheld computer.
To specify a destination path or to rename a file on your handĆheld computer, use
a line with the newname=oldname" format. This causes the file oldname" to
be read from the PC and transmitted to your handĆheld computer with the name
newname". Both oldname" and newname" may include path information.
EXAMPLE: The following is a sample download list file:
app.lzh
config.sys

SECTION 2DOS Device Drivers
2-4 6220 Hand-Held Computer Technical Reference
Drive Mapping Utility
MAPDRIVE.EXE is similar to UB T.COM, in that drive letters can be assigned
to other drives. MAPDRIVE:
"Maps two drives together so that the system allows access to only one deĆ
vice regardless which of the two drive letters was requested.
"Handles errors automatically within an application by invalidating any
drives that would normally result in an interrupt vector requiring interacĆ
tion at the DO level.
To assign a path to a drive letter, use the mapdrive.exe d=[path] syntax.
EXAMPLE: This sample assigns path (E:\temp) to drive A: mapdrive.exe A=E:\temp
To delete (or invalidate) an assignment for a drive letter, remove the assignment, using this
syntax. “D” represents the drive letter assignment to be removed: mapdrive.exe d=
A drive can be reassigned to its original assignment, using an assignment such as:
mapdrive.exe A=A:\
Multiple drive mappings can be performed with a single command line. This sample deletes
drive assignments for A: and B: mapdrive.exe A= B=
File Integrity Verification Utility
The DO Toolkit contains a utility, CRC32.EXE, which computes a 32Ćbit Cyclic
Redundancy Check (CRCĆ32) on a set of files. This check is computed using a
complex mathematical equation that results in a unique CRCĆ32 value. This
value guarantees accuracy of the file transfer so that even a minor change to a
file results in a dramatically different CRC. This CRC value can validate whethĆ
er system files are corrupt.
To verify file integrity, run CRC32.EXE to calculate the 32Ćbit CRC value. Then
compare that value with the factory CRC value. All factory CRCs are listed in
RELNOTE .TXT file in the Toolkit. Usage is as follows:
CRC32 [@][filename | pathname] [/s]
filename
The name of the file on which the CRC is calculated.
pathname
The location of the filename to be processed.
/s earch all subdirectories for matching filenames.
@Optionally included to indicate that filen me is an argument file,
containing names of files to be checked. A valid argument file for
CRC32.EXE has the same format as an argument file for IPLFMT.EXE.
"NOTE: Wildcard processing in the filename is allowed only on the command line, but not within the
argument file. CRC32.EXE processes directories with any attribute set, such as ‘read-only’.
One or more files or directories can be processed at one time. For command line
help, use the /? switch.

SECTION 2 DOS Device Drivers
6220 Hand-Held Computer Technical Reference 2-5
Get or Set ROM DOS Boot Flags
MMBFLAG.COM satisfies the following batch file requirements:
"The error level returned by MMBFLAG.COM indicates the current value of
the DO boot flags. The boot flags keep track of the default boot drive and
serve as an indicator of Master Mode Booting.
"Change the default boot drive using a command parameter (Note: Drives E
nd H re lso supported):
MMBFLAG.COM 2 (Drive C:)
MMBFLAG.COM 3 (Drive D:)
MMBFLAG.COM 4 (Drive E:)
T ble 2Ć1
MMBFLAG.COM Error Levels
Error Level Mea i g
132 Master Mode Boot from Drive B (default boot drive is E)
131 Master Mode Boot from Drive B (default boot drive is D)
130 Master Mode Boot from Drive B (default boot drive is C)
4 Drive E is the default boot drive
3 Drive D is the default boot drive
2 Drive C is the default boot drive
Multipurpose Delay Utility
DELAY.EXE serves the following functions:
"Displays a message to the screen (like the Echo command)
"Waits for specified amount of time before continuing (similar to the
leep command or DO 6 Choice command with a timeĆout specified)
"Pauses system execution until key is pressed (like the Pause command)
"Returns an error level based on which key was pressed (like the DO 6
Choice command)
The first three functions perform even when DELAY.EXE is loaded as a device
driver. ince the error level concept does not apply to CONFIG. Y processing,
the fourth function applies to command line (batch file) execution.
1. To display one or more different messages, supply the new messages within
quotes on the command line. Each quoted text string displays on a sepaĆ
rate line. Use a null message (") to display a blank line. To keep the curĆ
sor positioned immediately after the last character displayed, do not supply
the trailing quote ("). To display a message without waiting for either a
timeout or a keypress, specify a delay timeout of zero (/0).
2. To force DELAY.EXE to exit after a period of time, even with no key press,
specify the /nnnn" switch anywhere on the command line. The decimal
value of nnnn" is the hundredths of seconds to elapse before DELAY.EXE
exits. The maximum delay is about 640 seconds or ten minutes.
3. The /K parameter locks the keyboard during execution of DELAY.EXE.
4. When DELAY.EXE is executed from a command shell, the error level set
(upon return) is based on the key, if any, that was pressed prior to exiting.
The return value is geared to determine which numeric key was pressed.

SECTION 2DOS Device Drivers
2-6 6220 Hand-Held Computer Technical Reference
yntax: [device=]Delay[.exe] [/nnn [/K]] {”Message(s)”}
device=
Loads DELAY.EXE as a device driver. The full pathname for the
executable must be specified, as follows: device=c:\utils\delay.exe
When executing DELAY.EXE on the command line, omit device=" and
only include the full pathname for the executable if that path is not in the
PATH environment variable.
/nnn Forces DELAY.EXE to timeout, by specifying a timeout period. The
timeout period (nnn) is specified in hundredths of a second. Thus, /100
causes DELAY.EXE to timeout after one second. Note if DELAY.EXE is
from a DO box under Windows, the timeout duration is longer due to
how Windows implements the timeout function.
/K Disables the keyboard while pausing. pecify this switch fter providing
a timeout value or the delay cannot be terminated. Without this switch,
the delay terminates with a key press, even with a specified timeout.
{Messages(s)"
One or more messages can be specified on the command line. Each
message starts with an undisplayed quote (). If a trailing quote (") is not
supplied, then the cursor remains positioned immediately following the
message. Otherwise a carriage return and line feed is issued at the end of
the message. The default message is Press any key to continue..."
Errorlevel retur values:
When DELAY.EXE is run as a command, use the errorlevel set (the delay
is complete) to determine which key was pressed or whether a timeout
occurred. The return value states which numeric key was pressed. Below
are error levels and their common key pressed values.
"0 through 9 0" through 9"
"221 The YE key
"235 The NO key
"255 No key was pressed, the time already expired
"12 to 154 All other values are determined by subtracting 30h from
the key value returned by reading the keyboard directly.
EXAMPLE: Standard PC Function 6220 Commands Required to Perform Function
Pause DELAY.EXE
Wait for “1”to be pressed :Loop
DELAY.EXE “Press ‘1’to continue . . . “
If not errorlevel 1 goto Loop
If errorlevel 2 goto Loop
Echo “message”DELAY.EXE /0 “message”
Sleep 100 ms DELAY.EXE /10 “”
Echo “Pause for 1 second DELAY.EXE /100 /K “Pause for 1 second”
Sleep 1 second (with keyboard disabled)
Choice /c:12 “message”DELAY.EXE “message”
If errorlevel 3 goto InvalidDigit
If errorlevel 2 goto PressedTwo
If errorlevel 1 goto PressedOne
Echo “message two”DELAY.EXE “message two”“Press any key to continue”
Pause
Reset the System
RE ET.EXE resets the system for batch files or other software.