Intermec EasyCoder 201II User manual

EasyCoder 201 II
Memory Card Adapter Kit
P/N 1-960270-05
Edition 3
September 1998
Installation Instructions

EasyCoder 201 II – Installation Instructions
1
MEMORY CARD ADAPTER KIT
General Information This leaflet contains instructions on how to install a Memory Card
AdapterinanEasyCoder201IIorEasyCoder201IIEprinter.(The
adapter is fitted as standard in EasyCoder 201 IISA). This optional
device could be purchased as a kit for field installation by an
authorized technician. When such is the case, please follow the
present instruction sheets for maximum safety and performance.
Beforestartingtomodifyyourprinter,checkthattheMemoryCard
Adapter Kit is complete. It should include the following parts:
• 1 Memory Card Expansion Board
• 1 Memory Card Holder
• 1 Connection Cable
• 1 Address Decoder GAL 20V8
• 3 Screws
• 3 Washers
• This instruction booklet
Information in this manual is subject to change without prior notice and does
not represent a commitment on the part of Intermec Printer AB.
©CopyrightIntermecPTCAB,1998.Allrightsreserved.PublishedinSweden.
EasyCoder is a registered trademark of Intermec Technologies Corp.
EasyCoder 201 II
Memory Card Adapter Kit
Installation Instructions
Edition 3, September 1998
Part No. 1-960270-05

EasyCoder 201 II – Installation Instructions
2
❑Turn off the power . For extra safety, pull the power cord out of
the mains receptacle at the rear plate of the printer.
❑Open the right-hand door.
❑Loosen the two screws that hold the cover.
❑Pull out the cover. The left-hand door can be swung open, and
the logic part of the printer becomes accessible.
❑Loosen the front plate by unscrewing the five screws indicated
on the drawing below. Disconnect the display and keyboard
cables from their connectors on the CPU board.
MEMORY CARD ADAPTER KIT, cont'd.
Step-by-Step Installation
Instructions
CPU Board
Screws (2x)
Cover
Continued!

EasyCoder 201 II – Installation Instructions
3
MEMORY CARD ADAPTER KIT, cont'd.
Step-by-Step Installation
Instructions, cont'd. ❑Fit the Address Decoder on the Memory Card Board.
❑Insert the Memory Card Board into the Memory Card Holder.
❑Place the front plate upside down on the table.
❑Fasten the Memory Card Adapter assy. to the front plate by
means of the three screws with washers. Position the adapter at
appr. 16–17 mm (0.65") from the edge of the front plate, as
illustrated below.
❑Fitthe40-lineFlatCabletoconnectorP-1oftheMemoryCard
Adapter (see above).
Connector (P-1)
Address Decoder
Memory Card Board Memory Card Holder
Continued!
16 to 17 mm
(0.65")
Screws & Washers (3x)

EasyCoder 201 II – Installation Instructions
4
MEMORY CARD ADAPTER KIT, cont'd.
Step-by-Step Installation
Instructions, cont'd. ❑Mount the front plate back on the printer.
❑ConnectthecablefromtheMemoryCardAdaptertoconnector
P-2 on the CPU board. Fit exactly as illustrated and make sure
that it cannot be damaged by moveable mechanical parts.
❑Connect the display and keyboard cables.
❑Close the left-hand door and the top cover in reverse order (see
page 2).
❑Check that a memory card can easily be inserted and pulled out
from the adapter.
❑Checkthat theright-handdoor isnotobstructed bythememory
card.
❑Closetheright-handdoor,andinsertthemainscable.Switchon
power. The printer is now ready for use.
WARNING!
Becarefultomounttheflatcable
that connects the CPU board to
the Memory Card Adapter as
illustrated. Reversal of a con-
nector may cause damage to
components.
IMPORTANT!
Always switch off the power before
fitting or removing a memory card.
The printer's firmware will not
detect a memory card unless it is
inserted during power-up.
Blue colour marking
CPU Board
Memory Card Adapter