Intermec EasyCoder PF2i User manual

Service Manual
EasyCoder PF2i,
PF4i, and PF4i Com-
pact Industrial
printers

Intermec Printer AB
Idrottsvägen 10
P.O. Box 123
S-431 22 Mölndal
Sweden
Service support: [phone]
The information contained herein is proprietary and is provided solely for the purpose of allowing
customers to operate and/or service Intermec manufactured equipment and is not to be released,
reproduced, or used for any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change without notice.
© 2004by Intermec Printer AB
All Rights Reserved
EasyCoder, EasyLAN, Fingerprint, and LabelShop are registered trademarks of Intermec Tech-
nologies Corp. The word Intermec, the Intermec logo, InterDriver, and PrintSet are trademarks of
Intermec Technologies Corp.
The name Centronics is wholly owned by GENICOM Corporation.
Microsoft is a registered trademark of Microsoft Corporation.
Torx is a registered trademark of Camcar Division of Textron Inc.
TrueDoc is a registered trademark of Bitstream, Inc.
TrueType is a trademark of Apple Computer Inc.
Unicode is a trademark of Unicode Inc.
Windows is a trademark of Microsoft Corporation.
Throughout this manual, trademarked names may be used. Rather than put a trademark (™)
symbol in every occurrence of a trademarked name, we state that we are using the names only in an
editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual iii
Preface
Contents
About This Manual..............................................................................................................vi
Notices and Approvals.........................................................................................................vii
1 Models and Options
1.1 Identification..............................................................................................................2
1.2 EasyCoder PF2i Specifications .................................................................................11
1.3 EasyCoder PF4i Specifications .................................................................................13
1.4 EasyCoder PF4i Compact Industrial Specifications ..................................................15
1.5 Measures EasyCoder PF2i ........................................................................................17
1.6 Measures EasyCoder PF4i ........................................................................................21
1.7 Measures EasyCoder PF4i Compact Industrial.........................................................29
2 Front and Keyboard
2.1 Front........................................................................................................................36
2.2 Print Button.............................................................................................................36
2.3 Keyboard .................................................................................................................37
2.4 Console pcb. ............................................................................................................38
3 Covers and Doors
3.1 Right-Hand Doors...................................................................................................42
3.2 Front and Left-Hand Cover .....................................................................................47
3.3 Front Door...............................................................................................................48
4 Chassis
4.1 Description ..............................................................................................................50
4.2 Center Section .........................................................................................................51
4.3 Bottom Plate............................................................................................................51
4.4 Hinges .....................................................................................................................52
5 Media Supply
5.1 Internal Supply ........................................................................................................54
5.2 Media Guides...........................................................................................................57
5.3 External Supply........................................................................................................60
6 Transfer Ribbon Mechanism
6.1 Description ..............................................................................................................62
6.2 Ribbon Supply Unit.................................................................................................63
6.3 Ribbon Rewind Unit................................................................................................65
6.4 Ribbon Sensor..........................................................................................................66
6.5 Ribbon Motor..........................................................................................................68
6.6 Front Ribbon Break Shaft ........................................................................................69
6.7 Rear Ribbon Break Shaft..........................................................................................70
6.8 Printhead Ribbon Break Shaft..................................................................................71

iv Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Preface
7 Print Mechanism
7.1 Description ..............................................................................................................74
7.2 Platen Roller ............................................................................................................78
7.3 Stepper Motor..........................................................................................................80
7.4 Belts.........................................................................................................................82
7.5 Label Stop Sensor.....................................................................................................83
7.6 Printhead .................................................................................................................91
7.7 Headlift Sensor ........................................................................................................97
7.8 Headlift Mechanism.................................................................................................99
7.9 Media Feed Principles ............................................................................................103
8 Liner Takeup Unit
8.1 Description ............................................................................................................108
8.2 Takeup Unit Parts ..................................................................................................110
8.3 Fitting a Takeup Unit.............................................................................................111
8.4 Replacing the Timing Belt......................................................................................111
9 Label Taken Sensor
9.1 Description ............................................................................................................114
9.2 Replacement ..........................................................................................................115
9.3 Adjustment ............................................................................................................116
10 Paper Cutter
10.1 Description ............................................................................................................118
10.2 Installation.............................................................................................................119
10.3 Controlling the Cutter ...........................................................................................121
10.4 Media Load............................................................................................................121
10.5 Servicing ................................................................................................................122
10.6 Diagrams................................................................................................................124
11 Electronics Compartment
11.1 Introduction...........................................................................................................128
11.2 Accessing the Electronics Compartment.................................................................128
11.3 Main Parts..............................................................................................................129
12 Power Supply
12.1 Description ............................................................................................................132
12.2 Replacing the Power Supply Unit...........................................................................134
12.3 Components ..........................................................................................................136
12.4 Schematics .............................................................................................................138
13 CPU Board
13.1 Description ............................................................................................................142
13.2 Circuits ..................................................................................................................143
13.3 Connectors.............................................................................................................148
13.4 Test Points..............................................................................................................149
13.5 Startup ...................................................................................................................150

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual v
Preface
13.6 Components ..........................................................................................................151
13.7 Schematics .............................................................................................................153
13.8 Replacing the CPU Board ......................................................................................162
14 Interfaces
14.1 Introduction...........................................................................................................164
14.2 Serial Communication Port "uart1:" ......................................................................165
14.3 USB Interface.........................................................................................................166
14.4 Bar Code Wand Interface .......................................................................................167
14.5 Installing an Optional Interface Board ...................................................................168
14.6 Serial/Industrial Interface Board.............................................................................171
14.7 Double Serial Interface Board ................................................................................181
14.8 IEEE 1284 Parallel Interface Board ........................................................................191
14.9 EasyLAN Ethernet Interface Board ........................................................................195
14.10 EasyLAN Wireless Interface Board.........................................................................200
15 Troubleshooting
15.1 Diagnosing............................................................................................................. 208
15.2 No Reaction at Power Up....................................................................................... 210
15.3 Printer Stops Working after Startup........................................................................ 211
15.4 CPU Board Failures ...............................................................................................212
15.5 Power Supply Unit Failures .................................................................................... 213
15.6 Console Errors ....................................................................................................... 214
15.7 Error Messages ....................................................................................................... 216
15.8 No Communication (general) ................................................................................218
15.9 No Serial Communication ..................................................................................... 219
15.10 No Network Communication ................................................................................ 221
15.11 Sensor Malfunctions............................................................................................... 225
Label Stop Sensor (LSS) .................................................................................. 225
Headlift Sensor................................................................................................ 226
Label Taken Sensor (LTS) ................................................................................ 226
Ribbon Sensor ................................................................................................. 227
15.12 Printing Troubles.................................................................................................... 228
15.13 Ribbon Troubles..................................................................................................... 232
15.14 Liner Takeup Troubles............................................................................................ 234
15.15 Memory Card Troubles .......................................................................................... 235
15.16 Paper Cutter Troubles............................................................................................. 236
A Program Overviews
Intermec Shell Overview ...................................................................................................240
Setup Mode Overviews ....................................................................................................241
B Firmware Upgrading
Introduction......................................................................................................................254
General Principles .............................................................................................................254
Upgrading From a Memory Card......................................................................................255
Upgrading From the Host.................................................................................................257

vi Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Preface
About This Manual
This Service Manual is intended to facilitate installation, troubleshooting
and repair of the Intermec EasyCoder PF2i, PF4i, and PF4i Compact
Industrial in the versions delivered at the date of publishing. Thus, all
information on the Intermec Fingerprint firmware is based on version
8.10 and information on the the Intermec Programming Language (IPL)
is based on version 2.10. The on-going product improvement can be
followed in the Printer Technical Bulletins from Intermec.
Note that even if the printers are technical identical (with the exception of
the keyboard overlay), Fingerprint and IPL make the printer work quite
differently and certain devices and options are not supported by IPL.
Generally, illustrations in this manual show printers running Fingerprint.
This Service Manual is supplemented by the following publications,
which the service technician also should keep easily available in their latest
versions:
• Intermec EasyCoder PF2i, User’s Guide (Fingerprint version)
• Intermec EasyCoder PF4i, User’s Guide (Fingerprint version)
• Intermec EasyCoder PF4i Compact Industrial, User’s Guide (Finger-
print version)
• Intermec EasyCoder PF2i, User’s Guide (IPL version)
• Intermec EasyCoder PF4i, User’s Guide (IPL version)
• Intermec EasyCoder PF4i Compact Industrial, User’s Guide (IPL ver-
sion)
• Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial, Spare
Parts Catalog
• Installation Instructions for various options
• Intermec Direct Protocol v8.10 (or later), Programmer’s Reference
Manual
• Intermec Fingerprint v8.00 (or later), Tutorial
• Intermec Fingerprint v8.10 (or later), Programmer’s Reference Manual
• IPL Programming, Reference Manual (rev. 006 or later)
Please note that the operations described in this manual only should be car-
ried out by skilled and authorized personnel with proper training and full
understanding of written English. The printers contain wires and circuits
with up to 380V, which implies the risk of electrical shock. Moving parts
may also cause harm, if incorrectly manipulated.
It is assumed that the reader possesses reasonable skills in mechanics and
electronics and is familiar with the Intermec programming languages

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual vii
Preface
FCC Notice (United States of America)
WARNING
This equipment generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instructions manual, may
cause interference to radio communications. It has been tested and found
to comply with the limits for a Class A computing device pursuant to Sub-
part J of Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial envi-
ronment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to
take whatever measures may be required to correct the interference.
DOC Notice (Canada)
Canadian Dept. of Communication
REGULATIONS COMPLIANCE
(DOC-A)
This digital apparatus does not exceed the class A limits for radio noise
emissions from a digital apparatus as set out in the radio interference regu-
lations of the Canadian Department of Communication.
Ministère des Communications du Canada
CONFORMITE DE REGLEMENTS
(DOC-A)
Le présent appareil numérique n’émet pas de bruits radio-électriques dépas-
sant les limites applicables aux appareils numériques de classe A prescrites
dans le règlement sur brouillage radioélectrique édicté par le Ministère des
Communications du Canada.
GS Notice (Germany)
Allgemeine Vorschrift
Reparaturen oder sonstige Eingriffe, die sich nicht auf normale
Bedienung der Maschine beziehen, dürfen ausschließlich nur von einem
ausgebildeten, zuständigen Fachmann vorgenommen werden.
EU Standard EN 55022 (The European Union)
WARNING
This is a Class A ITE product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
Notices and Approvals

viii Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Preface
Declaration of Conformity (CE)
We,
Intermec Printer AB
Idrottsvägen 10
Box 123
S-431 22 Mölndal
Sweden
declare under our sole responsibility1that the products
EasyCoder PF2i,EasyCoder PF4i,and EasyCoder PF4i Compact Industrial
to which this declaration relates
is in conformity with the following standards
EMC:
EN 61000-6-4:2001
EN 61000-6-2:2001
Electrical Safety:
EN 60 950
following the provisions of Directives
89/336/EEC and 73/23/EEC
Mölndal 2003-03-12
...................................................................
Per-Ove Jacobsson
1/. Intermec assumes no responsibility regarding the CE Directive if the printer is handled,
modified or installed in other manners than those described in the manuals.

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual 1
1 Models and Options
This chapter describes how to identify the various models in the EasyCoder
PF2i/PF4i-series of printers, provides comprehensive technical specifica-
tions, and gives all important measurements.

2 Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Chapter 1—Models and Options
1.1 Identification
EasyCoder PF2i
The EasyCoder PF2i comes either as a dedicated direct thermal printer or,
optionally, as a combined direct thermal/thermal transfer printer. It can use
media up to 60 mm (2.36 inches) wide and has a print width of 56 mm
(2.2 inches). It has an 8 dots/mm (203.2 dpi) printhead.
The printer runs either Intermec Fingerprint Programming Language (FP)
v8.10 (or later) or Intermec Programming Language (IPL) v2.10 or later.
Externally, the difference is visible on the keyboard overlay. Fingerprint
printers have 22 keys and IPL printers have 7 keys.
Keyboard shows printer model
Narrow front on side door
Keyboard shows printer model
Narrow front on side door
Keyboard shows printer model
Narrow front on side door
EasyCoder PF2i (Fingerprint version)
EasyCoder PF2i (IPL version)

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual 3
Chapter 1—Models and Options
EasyCoder PF4i
The EasyCoder PF4i comes either as a dedicated direct thermal printer
or a combined direct thermal/thermal transfer printer. It has an 8 dots/
mm (203.2 dpi) or an 11.81 dots/mm (300 dpi) printhead (IPL only 8
dots/mm). It can use media up to 114.3 mm (4.5 inches) wide and has a
maximum print width of 104 mm (4.095 inches) at 8 dots/mm or 105.7
mm (4.161 inches) at 11.81 dots/mm.
The printer runs either Intermec Fingerprint Programming Language (FP)
v8.10 (or later) or Intermec Programming Language (IPL) v2.10 or later.
Externally, the difference is visible on the keyboard overlay. Fingerprint
printers have 22 keys and IPL printers have 7 keys.
Keyboard shows printer model
Wide front on side door
EasyCoder PF4i (Fingerprint version)
Keyboard shows printer model
Wide front on side door
Keyboard shows printer model
Wide front on side door
Keyboard shows printer model
Wide front on side door
EasyCoder PF4i (IPL version)

4 Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Chapter 1—Models and Options
EasyCoder PF4i Compact Industrial
The EasyCoder PF4i Compact Industrial is a special model of Easy-
Coder PF4i that has been adapted for demanding industrial applications.
It differs from EasyCoder PF4i in having a dark-painted casing, stronger
hinges, a front door, a full metal media supply roll post, and a modified
print mechanism. The EasyCoder PF4i comes either as a dedicated direct
thermal printer or a combined direct thermal/thermal transfer printer. It
has an 8 dots/mm (203.2 dpi) or an 11.81 dots/mm (300 dpi) printhead
(IPL only 8 dots/mm). It can use media up to 114.3 mm (4.5 inches) wide
and has a maximum print width of 104 mm (4.095 inches) at 8 dots/mm
or 105.7 mm (4.161 inches) at 11.81 dots/mm.
The printer runs either Intermec Fingerprint Programming Language (FP)
v8.10 (or later) or Intermec Programming Language (IPL) v2.10 or later.
Externally, the difference is visible on the keyboard overlay. Fingerprint
printers have 22 keys and IPL printers have 7 keys.
Front door
EasyCoder PF4i Compact Industrial (Fingerprint version)
EasyCoder PF4i Compact Industrial (IPL version)
Front door

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual 5
Chapter 1—Models and Options
Machine label
All Models
The printer can use any 100 to 240 VAC, 50 to 60Hz voltage. There is no
voltage switch-over.
The machine label on the printer’s rear plate contains type, part number,
serial number, and signs of approval.

6 Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Chapter 1—Models and Options
2
1
4
3
bw
fw
Options for EasyCoder PF2i
The EasyCoder PF2i can be fitted with a number of options:
• Transfer Ribbon Mechanism (see Chapter 6)
• Label Taken Sensor (see Chapter 9)
• Liner Takeup Unit (see Chapter 8)
• Media Supply Hub (replaces Supply Post) (see Chapter 5)
• 3-inch Adapter (for Media Supply Hub) (see Chapter 5)
• Quick-Load Guides (see Chapter 5)
• Long or Short Side Door (see Chapter 3)
• Real Time Clock Circuit (not IPL) (see Chapter 13)
• Interface boards of various types (see Chapter 14)
Label taken
sensor
3-inch adapter
Quick-Load guides
Short side door
Media supply
roll post with
edge guide
Long side door
Liner takeup
with guide
shaft
Media supply
hub
Transfer ribbon
mechanism

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual 7
Chapter 1—Models and Options
Options for EasyCoder PF4i
The EasyCoder PF4i can be fitted with a number of options:
• Label Taken Sensor (see Chapter 9)
• Liner Takeup Unit (see Chapter 8)
• Paper Cutter (see Chapter 10)
• Media Supply Hub (replaces Supply Post) (see Chapter 5)
• Printhead Spring (for vertical mounting) (see Chapter 7)
• 3-inch Adapter (for media supply hub) (see Chapter 5)
• Quick-Load Guides (wide/narrow) (see Chapter 5)
• Long/Short Side Door or Megatop (see Chapter 3)
• Real-time Clock Circuit (not IPL) (see Chapter 13)
• Interface boards of various types (see Chapter 14)
Label taken sensor
3-inch
adapter
Quick-Load guides
(wide & narrow)
Short side
door
Media supply hub
8-inch Megatop
Liner takeup
with guide
shaft
Transfer ribbon
mMechanism
Media supply
roll post with
edge guide
Long side
door
Tray
Paper
cutter
Printhead spring
Optional printheads

8 Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Chapter 1—Models and Options
EasyCoder PF4i Compact Industrial
The EasyCoder PF4i Compact Industrial can be fitted with a number of
options:
• Label Taken Sensor (see Chapter 9)
• Liner Takeup Unit (see Chapter 8)
• Paper Cutter (see Chapter 10)
• Media Supply Hub (see Chapter 5)
• 3-inch Adapter (for media supply hub) (see Chapter 5)
• Quick-Load Guides (wide/narrow) (see Chapter 5)
• Long Door or Megatop (see Chapter 3)
• Real-time Clock Circuit (not IPL) (see Chapter 13)
• Interface boards of various types (see Chapter 14)
Label taken
sensor
Liner takeup
with guide shaft
Quick-Load guides
(narrow and wide)
Front door
Media supply
roll post
Long side door
8-inch Megatop
Paper
cutter
Tray
Media supply hub
3-inch adapter
Optional printheads

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual 9
Chapter 1—Models and Options
Interfaces
The printers are as standard provided with one serial RS-232 port, one
serial USB port, and one wand interface. The USB port and the wand
interface are not supported by IPL. In addition, one EasyLAN interface
and one extra interface board can be fitted, see Chapter 14.
Serial port RS-232
USB port (not
used IPL)
Provision for one
interface board (IPL
only IEEE 1284)
Provision for
Ethernet connector
Wand interface (not
IPL)

10 Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Chapter 1—Models and Options
Checking Hardware and Firmware
Finally, you may want to inspect the electronics compartment. To do so,
carefully follow the instructions in Chapter 11.
Always switch off the power and remove the power cord before removing
the cover over the electronics compartment! Dangerous voltage!
In the electronics compartment, check:
• Type of CPU board?
- Check number and size of Flash SIMMs.
- Check size of SDRAM SIMM.
• Any optional interface board fitted?
- Check type, straps, and optional circuits.
Refer to Chapters 13 and 14 for more information.
Being delivered with either Intermec Fingerprint v8.xx programming
language or IPL v2.xx (Intermec Programming Language), the printer
can eisily be converted from Fingerprint to IPL or vice versa using a
firmware card or special software. The keyboard overlay will also need to be
switched. The type of firmware is indicated by the messages in the display
window.
Fingerprint only
If the printer is working and possible startup program can be interrupted,
the type of program in the printer can be identified. Connect printer
and computer, open a suitable communication program, and start up the
printer in Fingerprint’s immediate mode. The instruction FILES allows
you to check what files the various parts of the printer's memory contain.
The statements FONTS and IMAGES can be used for the same purpose
regarding fonts and images. Use the VERSION$ function to check version
of the Intermec Fingerprint firmware.
You can read the setup in the Setup Mode or using Intermec Shell, which
also allows you to print test labels containing the present setup values.
To enter Shell if a custom-made autoexec-file prevents access, lift the
printhead and press any key on the printer's keyboard (except the <Shift>
key), then turn on the power while continuing to press the key. When the
Shell countdown begins, release the key and press <Enter> to start Shell.
Do not forget to lower the printhead if you want to print for example test
labels. Refer to the User’s Guide and to Appendix 1 in this Service Manual
for more information on the Setup Mode and the Intermec Shell startup
program.
If the printer still does not work, you may need to interview the user.
IPL only
The Test/Service part of the Setup Mode allows several types of test labels
to be printed (see the User’s Guide and Appendix A). IPL also has a number
of commands that return valuable information on the printer’s status (see
IPL Programming, Reference Manual).

Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual 11
Chapter 1—Models and Options
Printing
Print Technique Direct Thermal (Thermal Transfer as option)
Printhead Resolution 8 dots/mm (203.2 dpi)
Print Speed (variable) 100 to 200 mm/sec. (approx. 4 to 8 in./sec.)
Print Width (max) 56 mm (2.2 in.) = 448 dots
Print Length (max) 32767 dots = 409.5 cm (161.25 in.)1
Media Width (min/max) 25 to 60 mm (1.00 to 2.36 in.) Standard edge guide
Media Width (min/max) 40 to 60 mm (1.57 to 2.36 in.) Quick-Load guides
Media Roll Diameter (max) 213 mm (8.38 in.) Short door/no takeup
Media Roll Core Diameter 38 to 40 mm (1.5 in.) or 76 mm (3 in.)
Ribbon Width (min/max) 25 to 60 mm (1 to 2.36 in.)
Ribbon Roll Diameter, Outer (max) 65 mm (2.44 in.) 240-300 m (787-985 ft)
Ribbor Roll Core Diameter, Inner 25.4 mm (1 in.)
Print Directions 4
Modes of Operation
Tear Off (Straight-through) Yes
Peel Off (Self-strip) Optional With liner takeup unit
Firmware (Fingerprint)
Operating System Intermec Fingerprint v8.10 Incl. Direct Protocol
Smooth Fonts TrueDoc and TrueType fonts
Built-in scaleable fonts (std) 15 Unicode fonts2
Built-in bar code symbologies (std) 45
Startup Program (std) Intermec Shell v8.0
Firmware (IPL)
Operating System IPL v2.10
Built-in scaleable fonts (std) 13 scaleable + 21 simulated bitmap
Built-in bar code symbologies (std) 31
Physical Measures
Dimensions (W×L×H) 194×397×178 mm (7.64×15.63×7.00 in.) With long side door
Weight (excluding media) approx. 5.5 kg (12 pounds)
Ambient Operating Temperature +5°C to +40°C (+41°F to +104°F)
Humidity 20 to 80% non-condensing
Electronics
Microprocessor 32 bit RISC
On-board Flash SIMMs 2 sockets (for 4 or 8 MB each) Std. 1 × 4MB
On-board SDRAM SIMM 1 socket (for 8 or 16 MB) Std. 1 × 8MB
Power Supply
AC Voltage 90 to 265 VAC, 45 to 65Hz
PFC Regulation IEC 61000-3-2
Power Consumption Standby 15W; Peak 300W
Sensors
Label Gap/Black Mark/Out of Media Yes 5 fixed positions
Printhead Lifted Yes
1.2 EasyCoder PF2i Specifications

12 Intermec EasyCoder PF2i, PF4i, and PF4i Compact Industrial—Service Manual
Chapter 1—Models and Options
Ribbon End/Ribbon Low Yes (thermal transfer model only)
Controls
Control Lamps 3
Display 2 × 16 character LCD with background light
Keyboard Fingerprint: 22 keys; IPL: 7 keys Membrane-switch type
Print or Feed/Pause button 1
Beeper Yes
Data Interfaces
Serial 1×RS-232 + 1×USB USB not supp. by IPL
Bar Code Wand 1 Not supported by IPL
Connection for Interface Boards 1 + 1 1 EasyLAN + 1 other
Memory Card Adapter 1 CompactFlash cards
Accessories and Options
Thermal Transfer Mechanism Option
Integral Self-strip Unit w. Liner Takeup Option For peel-off operation
Rotating Media Supply Hub Option Replaces supply post
3-inch Adapter Option For media supply hub
Short Side Door Option3
Long Side Door Option3
Label Taken Sensor Option
Real Time Clock Option (not IPL) 10+ years life
RS-232 Interface Cable Option
Parallel Interface Cable Option
IEEE 1284 Parallel Interface Board Option
Double Serial Interface Board Option (not IPL)
Serial/Industrial Interface Board Option (not IPL)
EasyLAN Ethernet Interface Option Model EasyLAN100i2
EasyLAN Wireless Interface Option Model Wireless 100i2
External Alphanumeric Keyboard Option (not IPL)
CompactFlash Cards Option 8MB to 1GB
CompactFlash Card Protection Plate Option
1/. The max. print length is also restricted by the amount of free SDRAM memory.
2/. Latin, Greek, and Cyrillic fonts according to Unicode standard are included.
3/. Type of door fitted at delivery depends on model.