Interpump Group General Pump 103166 User manual
103166
ACCESSORIES ACCESSORIES
GENERAL PUMP A member of the Interpump Group
SPECIFICATIONS
PART NUMBER 103166*
Voltage 12V DC
*Hose reel sold separately
FEATURES / BENEFITS
• Allows for effortless rewinding of hose
• Free spin allows for easy pulling out of hose
• Durable powdercoated finish
• Stainless steel hardware
Electric Hose Reel Motor
DIMENSIONS (in/mm)
8
Ref 310136 Rev A
07-18
General Pump
is a member of
the Interpump Group
DHRA50300 & 103166
SHOWN
• Long lasting hardened gears
• Fits all DHRA hose reels
Ø 17.7”
18.6”
23.0”
Assembled power rewind kits availble
• A5015012 - DHRA50150 assembled with 103166
• A5030012 - DHRA50300 assembled with 103166
• A5045012 - DHRA50450 assembled with 103166
ASSEMBLY INSTRUCTIONS
GENERAL PUMP A member of the Interpump Group 103166
Electric Hose Reel Motor
1. On the end of the hose reel opposite the lock, assembley the two ring gear halves to the hose reel using carriage
bolts, washers and lock nuts. Finger tight only for now.
2. Assemble plate motor with bolts, lock washer and flat washers as shown. Torque to 100 in-lb.
3. Slide spur gear onto motor shaft; gear face will hang over with end of motor shaft by about 5 mm (3/16”). Apply a
drop of medium strength thread locker to the set screw and thread into gear. Torque set screw to 20 in-lb
4. Attach motor assembly to hose reel frame using carriage bolts, flat washers (bottom two bolts only), flat washers,
and locknuts. Finger tight only for now.
5. Insert the supplied spacers between the two ring gear gaps.
6. Rotate the hose reel by hand a few revolutions to get the motor assembly and ring gears to align. Tighten the ring
gear and motor assembly nuts to 100 in-lb. Remove spacers.
Ring Half (2X)
P/N 530079
(Kit 103166)
Washer, Flat, M8 (8X)
P/N 2203402
(Kit 103166)
Bolt, Carriage, M8 (8X)
P/N 2200117
(Kit 103166)
Nut, Lock, M8 (8X)
P/N 2200053
(Kit 103166)
Lock
Rings Concentric
with Center Shaft
Insert Spacers
Here
Spacer
Ref 310136 Rev A
07-18
GENERAL PUMP • 1174 Northland Drive • Mendota Heights, MN 55120
SAFTY PRECAUTIONS
WARNING!
Exposure of skin directly to
pressurized air or fluids could
result in severe bodily injury!
1. Make sure incoming pressure does not exceed
the rated pressure.
2. Use proper eye protection when assembling and
using the hose reel.
3. Assemble the hose reel on a clean workbench
free of debris and moisture.
4. Use soap and water when checking for air leaks.
5. Keep children away from work area.
Ref 3101356 Rev A
07-18
Screw Set, M4
P/N 2200115
(Kit 103166)
Gear, Spur, 12T
P/N 2530129
(Kit 103166)
Washer, Lock, M8 (4X)
P/N 2203507
(Kit 103166)
Washer, Flat, M8 (4X)
P/N 2203402
(Kit 103166)
Plate, Motor
P/N 2540113
(Kit 103166)
GENERAL PUMP A member of the Interpump Group 103166
Electric Hose Reel Motor
Cap, 1/2 NPT-F
P/N 2530130
(Kit 103166)
Nut, Lock, M8 (4X)
P/N 2200053
(Kit 103166)
Washer, Flat, M8 (4X)
P/N 2203402
(Kit 103166)
Bolt Carriage, M8 (4X)
P/N 2200117
(Kit 103166)
Washer, Flat, M12 (2X)
P/N 2203412
(Kit 103116)
BOTTOM TWO
BOLTS ONLY
Motor, 12V
P/N 2639000
(Kit 103166)
Other Interpump Group Engine manuals
