Invacare top end pro 2 all sport User manual

Assembly Instructions
Invacare® Top End® Pro™-2 All Sport
Wheelchair
Part #: 1181409
Rev: A Be sure to record your serial number and read the owners manual.

What you will receive
Box includes:
Complete wheel assemblies
Base frame
Seat frame(assembled w/ side
guards, upholstery, cushion,
and frame protector)
Footrest
Axles
Adjustable anti-tip assembly
Positioning strap
All attaching hardware.
Seat frame
Base Frame
Footrest
Hardware

Tools you will need:
Adjustable wrench
5mm allen wrench
4mm allen wrench
Two 10 mm combination wrenches or socket
7/16 and ¾ inch wrench
An assistant may also be helpful to hold frame in place while installing seat frame
Entire assembly should take about 30-45 minutes

Step one –Adjusting and installing wheels
A. Adjust the nut on the axle receiver.
The axle receiver nut will be loosely installed on the axle receiver bolt, this nut will need to be
tightened down with the adjustable wrench.
B. Adjust the nut on the actual axle so that the ball bearing locks into place when
put through the wheels and inserted into axle receiver.
AB

Step two –Installing anti-tip
Install adjustable anti-tip wheel.
A. Release and loosen the quick release lever attached to the anti-tip clamp
B. Insert adjustable anti-tip into base frame, with wheel facing down.
C. With rear wheels still on tighten quick release lever with anti-tip at level desired
(should be about a fingers width off the ground)
Wheels can be taken off after this is done, which will prevent the chair from rolling around while
installing the other parts.
ABC

Step three –Attaching the L brackets
There will be L brackets and curved brackets
The L brackets are for the front, and curved for the rear
The L brackets attach with the bolts that are bagged with 4 bolts that are all the same
size.
The curved brackets attach with the bolts that are bagged with 2 short bolts and 2 longer
bolts and then separate bag with 2 single bolts.
Note : Bolts should be left a little loose until all are installed.
Front L brackets
Rear Curved
brackets
These bolts will
be used instead
of the two larger
bolts in the
hardware bag for
the curved
brackets

Step three –continued (L brackets)
Attach the L brackets to the inside of the welded tabs on the seat frame.
Insert the bolt from the inside of the seat frame (use one flat washer, one split washer, and one
nut for each bolt.
Use the two 10MM wrenches to hold and tighten the bolts.
Keep in mind that the hole that you choose to mount the L bracket in will
determine the center of gravity on the chair.
Refer to page 40 of the owners manual

Step four –Curved brackets
Attach the curved brackets to the inside of the welded tabs on the seat frame.
» You will want to take the larger bolts out of the bag and set them aside(these are
extras and will not be used on the chair, use the two smaller bolts in the hardware bag
to attach each curved bracket to the chair.
» The bolts which are bagged separately will be used to attach the curved bracket to the
base frame.
Insert the bolts from the outside of the seat frame (use one flat washer, one
nordlock washer, and one nut for each bolt.
» Use a 10MM wrench and a 4MM allen wrench to tighten the bolts in place.
These will be
used instead

Step four - continued
Be sure to leave the brackets slightly loose,
so that they can be adjusted and attached to
the base frame

Step five –Attach seat frame to base frame
Take seat frame and place it on top of the base frame, with the brackets lined up to the tabs
welded in the rear and the holes drilled in the frame on the front.
Use the coped washers and the bolts that are bagged together to attach the front L brackets
into the hole.
Use the bolts that had been set aside earlier to attach the curved brackets to the welded tab.
Now go back to the brackets on the seat frame, and make sure to tighten them all the way
down.