Inverter Fusion Fusion MultiClean User manual

Fusion MultiClean
Electrolytic Weld
Cleaning Machine
Operating Instructions
DIGITAL INVERTER WELDING TECHNOLOGY

1. General
The Fusion MultiClean machine is intended to be used for cleaning
stainless steel, aluminium & other metals after welding.
It is a single phase machine which runs off either a 230v or 110v
supply depending on the model. It is IP23 rated so can be used in
areas of dust and damp but is not waterproof.
N.B. Always wear suitable eye protection, gloves & protective
clothing whilst operating the machine & handling the fluids.
2. Setting Up
The red lead should be connected from the Positive (+) terminal
on the cleaner and clipped onto the work to be
cleaned.
The black lead should be connected from the
Negative (-) terminal on the cleaner to the brush.
3. Cleaning
 Set the High/Low switch to low (amber LED)
for stainless steel or high (green LED) for
aluminium.
 Set the Clean/Polish switch to clean (amber
LED).
 Dip the brushes into the cleaning solution, switch the machine
On and clean the work using a gentle painting motion. N.B. do
not “jab” the brushes against the metal as this will damage the
bristles.
 Spray with water & wipe to remove any excess fluid. Rinse the
brushes with water.
4. Polishing
 Set the High/Low switch to low (amber LED) for stainless steel
or high (green LED) for aluminium.
 Set the Clean/Polish switch to polish (green LED).
 Dip the brushes into the polishing solution, switch the machine
On and polish the work using a gentle painting motion. N.B. do
not “jab” the brushes against the metal as this will damage the
bristles.
 Spray with water & wipe to remove any excess fluid. Rinse the
brushes with water.

5. Embossing/Marking
 Set the High/Low switch to high (the green LED will light up).
 Set the Clean/Polish switch to clean (amber LED).
 Position your stencil where you want the embossing to appear.
 Dip the brushes into the embossing solution, switch the machine
On and wipe the brushes gently over the stencil, taking care not
to touch the surrounding metal, until the markings appear in
black.
 Spray with water and wipe to remove any excess solution then
remove the stencil.
6. Notes
 The leads, cleaning tools and work piece can become very warm
during use, this is normal and not a fault of the machine.
 Sparks will be generated during the cleaning process —this is
normal and they are not harmful.
 The Fusion MultiClean can be used with a single brush only if it
used on the low setting.
7. Caution
 Use in a well ventilated area and do not inhale the fumes given
off by the cleaning and polishing process.
 The sparks generated during the cleaning process are not
harmful but they could ignite flammable gas so make sure any
nearby gas cylinders or appliances are free from leaks.
 If the leads are accidentally shorted out the unit will 'trip'. If this
occurs wait 5 minutes and after removing the short press the
black button in on the front of the machine to reset the trip.
 Never use leads other than those supplied and do not extend the
supplied leads, this could cause overheating and risk of fire.
 Do not operate the switches whilst cleaning/polishing is in
progress as this may cause internal damage.
8. After-sales Service & Warranty
Should you have any problems with the set-up or operation of your
Fusion MultiClean machine please feel free to contact us on 01404
549791 and our experienced engineers will be happy to give you
advice and assistance.
Your Fusion MultiClean machine is covered by a comprehensive 3
year parts and labour warranty - in the event of a breakdown
please contact us on 01404 549791.

Designed and manufactured in Britain by:
Inverter Fusion Ltd
Heathpark Way
Heathpark Industrial Park
Honiton
Devon
EX14 1BB
Tel: [phone]
Fax: [phone]
Email: sa[email protected]
Web: www.inverterfusion.co.uk