Inverto Unifiber IDLF-RXQXO1 OPR Series User manual
2
1. Optical Quattro Recivers
PRODUCT DESCRIPTION
The optical receivers 6125/ 6126/ 6131/ 6132 ( are intended to convert optical signals into elec-
trical RF signals. The recivers are compatible with Inverto wideband SAT IF transmitting system.
The receiver is equipped with AGC system based on optical input level (OLC - optical level con-
trol). The product is intended for indoor usage only.
SAFETY INSTRUCTIONS
■Installation of the receiver must be done according IEC60728-11 and national safety standards.
■The receiver is powered from low DC voltage, which is not dangerous to life.
■Any repairs must be done by a skilled personnel.
To ensure safe operation of the receiver follow these instructions:
■Do not connect supply voltage until all cables have been connected correctly.
■Receiver shall not be exposed to dripping or splashing water.
■Avoid placing receiver next to central heating components and in areas of high humidity.
■If the receiver has been kept in cold conditions for a long time, keep it in a warm room no less
than 2 hours before powering.
■The ventilation should not be impeded by covering receiver with items, such as newspapers,
table-cloths, curtains.
■Avoid looking directly into beam, laser light can cause eye injuries and result in permanent loss
of vision.
This product complies with the relevant clauses of the European Directive 2012/19/
EC. The unit must be recycled or discarded according to applicable local and national
regulations.
Equipment intended for indoor usage only.
Functional grounding. Connect to the main potential equalization.
This product is in accordance to following norms of EU: EMC norm EN50083-2, safety
norm EN62368-1 and RoHS norm EN50581.
This product is in accordance with Custom Union Technical Regulations: “Electromagnetic
compatibility of technical equipment“ CU TR 020/2011, “On safety of low-voltage equip-
ment“ CU TR 004/2011.
3
EXTERNAL VIEW OF THE RECEIVERS
Items: 6131/6132
Items: 6125/6126
123456
7
9
10
11
8
123456
7
9
8
Figure 1. External view of the receivers
4
1. OPTICAL IN Optical input. FC/UPC connector
2. DTT DTT, DAB, FM output. F-type, female
3. Horizontal High out (DC in) SAT IF horizontal high RF signal output, DC input. F socket
4. Vertical High out (DC in) SAT IF vertical high RF signal output, DC input. F socket
5. Horizontal Low out (DC in) SAT IF horizontal low RF signal output, DC input. F socket.
6. Vertical Low out (DC in) SAT IF vertical low RF signal output, DC input. F socket.
7. Functional grounding clamp
8. LED indicator of optical input power:
- Red – too high
- Green – correct (OLC range)
- Yellow – too low
9. DC IN 10 V ÷ 20 V DC powering input (3.5/1.3 mm DC jack)
10. Vertical out (DC in) SAT IF vertical polarization output, DC input. F socket
11. Horizontal out (DC in) SAT IF horizontal polarization output, DC input. F socket
OPTICAL CONNECTIONS
Note: All optical connectors and adaptors should be cleaned before connecting them.
If optical reception power of the receiver decrease, ber connection should be cleaned and maintained.
Reel cleaners or prepackaged lint free wipes or swabs with alcohol are the most convenient means
of cleaning optical connectors.
Fiber connectors should never be left uncovered.
1. Align the FC/UPC connector key-way (type R) with the receptable key-way.
2. Push rmly to locate the key-ways and then rotate the coupling ring.
3. Do not exceed the minimum bending radius of bers: must be not less 30 mm when connect-
ing optic cable to the system.
5
Installation instructions
- Read the safety instruction rst.
- All unused F type connectors must be terminated with 75 Ω loads.
- Mount receiver in vertical position with optical connector underneath.
- From top, left and right side leave 10 cm free space.
- Fasten with screws. Screws are not included in a package.
Powering
The receiver can be powered in two ways: from AC/DC adapter through 3.5/1.3 DC connector (pos.
9, Figure 1) or through RF outputs (pos. 3, 4, 5, 6, 10, 11 Figure 1).
DC-DCRx
DTT
DC
V,LoH,LoV,HiH,HiVH
Figure 2. DC path diagram
Optical input and RF outputs
The operational optical input level of the receiver is -15...-5 dBm. In this region OLC is working and
provides xed RF output levels. Ensure optical input level in this range.
A direct optical connection cannot be made between the transmitter and the receiver. Use appropriate
optical attenuator.
Requirements for external power supply unit (PSU)
Output voltage 10 V ÷ 20 V DC
■Output current recommended to use PSU with 50% extra power reserve
■Ripple at single and/or double mains frequencye < 10 mV p-p
■Ripple & noise < 200 mV p-p
■Output connector type 3.5/1.3 (+) plug
■Short circuit protection
■Double insulated (marked )
Meet EN 55022 class B conducted emisions requirements, measuring with grounded load
6
Technical Specications
Optical input
Detection wavelength range 1100 - 1650 nm
Input level (OLC range)* -15 ÷ -5 dBm
Return loss > 40 dB
Wideband and quattro outputs
Frequency range wideband 2x (290-2340 MHz) 2x (300-2350 MHz) -
MHz) quattro 2 x (950-2150) & 2 x (1100-2150) MHz
Output level wideband 80 dBµV -
quattro 80 dBµV
DTT output
Frequency range 87.5-240/470-790 MHz
Output level 80 dBµV
General
Internal IF 290-2340 MHz 300-2350 MHZ 300-2350 MHz 290-2340 MHz
Return loss / impedance > 10 dB / 75 Ω
Supply voltage range DC input 10-20 V
Wideband output 10-20 V -
Power consumption 4.8 W 4.6 W
Operating temperature range -20 oC ÷ + 50 oC
Dimensions/Weight (packed) 147x89x26 mm/0.4 kg 149x89x26 mm/0.4 kg
Item 6125 6126 6131 6132
* The system performance depends on optical level
7
8
For purpose of brevity, some product descriptions in this sheet remain at platform level and may not be referred to as de-
tailed datasheets of the products. Inverto Digital Labs reserves the right to amend, omit or add products, product-lines, and /
or features without notice. As product specifications may change without notice, always contact Inverto to obtain the latest
product specification sheets.
FTA Communication Technologies S.à.r.l Tel. +352 264 367 1 Fax. +352 264 313 68 V190522
This manual suits for next models
4
Table of contents
Other Inverto Receiver manuals
