3
Step 3 Securing Wall Mount to your Wall
This bracket is designed to be attached to either fixed wooden studs within traditional plasterboard (drywall)
walls or into solid brick or concrete walls.
Step 3a Wood Stud Installation
1. For mounting to wooden studs – carefully locate the
wooden stud and mark the position of the holes level
vertically and drill into the wood using a 4mm drill to a
depth of 80mm - see Diagram ‘C’.
2. To mount your bracket hold in position and insert the
supplied screws ‘L’ and fully tighten into the wood using a
12mm socket set or spanner.
Plastic plugs ‘M’ are not required but you may need
plasterboard fixings if there is no stud where you are
securing the TV bracket to the wall. Professional
advice maybe required if you use other fixings.
WARNING:
Spanner K is not to be used with wall fixings
Diagram ‘C’
Diagram ‘D’
WARNING:
Spanner K is not to be used with wall fixings
Step 3b Brick & Concrete Installation
1. For mounting to concrete or brick walls, please mark
the wall carefully - see diagram ‘D’. Once marked use a
10mm masonry drill bit and drill to a full length of 80mm
minimum ensuring the holes drilled are free from
debris - see step 3c and diagram ‘E’.
2. Fully insert the plastic plugs ‘M’ into the brick/concrete
(pushed beyond any plaster). Please ensure they fit
securely and are not visible in the holes before tightening
the screws in the plastic plugs.
3. To mount your bracket hold in position and insert the
supplied screws ‘L’ into the plastic plugs ‘M’ and fully
tighten using a 12mm socket set or spanner.
Step 3c
1. Many modern houses have an air-gap behind plasterboard or drywall. Our fixings are only designed to work
with the plastic plug fully inserted into the brick/concrete that lies behind any plaster or drywall air gap. To use
our fixings in this way YOU MUST insert the plug past any plaster/drywall and fully into the underlying
brick/concrete to gain a secure fixing. (The drill depth may have to be increased to make sure the plug can
be fully inserted to the brick/concrete.
2. When fitting, the screw must be at least 3/4 of the way into the plug, and the plug must be fully inserted into
brick/concrete to be effective - see Diagram ‘E’.
3. Depending on the plasterboard/drywall air gap you may need to purchase longer fixings to ensure a secure
fix.
Diagram ‘E’
WARNING
Please see diagram below
for correct installation of
screws and plugs
For low/medium density block work wall fixings may spin
and chemical/resin fixings (NOT INCLUDED) may be
required to achieve a secure fixing. Contact us or seek
professional advice if fixings are not engaging correctly.
Plaster
board/
drywall
Dot dab/
Air gap
Brick/concrete
wall
Plaster
board/
drywall
Dot dab/
Air gap
Brick/concrete
wall
Plaster
board/
drywall
Dot dab/
Air gap
Low/Medium
density block work
Step 4 Securing and Level Adjustment of your TV - (Two people are recommended to complete this step)
1. Carefully lift the TV and TV mounting plate assembly from Step 2 and hook the keyhole slot (1.) over the
wall brackets circular safety securing point (2.) and slide down to secure in place - see Diagram ‘F’.
(Before letting go, pull down gently to test TV is located securely whilst keeping a firm grip of the TV).
2. Once located in place replace the 2x M6 securing bolts which were removed in Step 1, check your TV
is level then fully tighten both bolts with spanner K to secure your TV to the wall bracket.
3. Replace the wall fixing plate covers that were also removed in Step 1.
or
Spanner K
M6 securing bolts
Diagram ‘F’
1
1
2
2
Step 5 Cable Management and Tilt Adjustment
1. Remove the cable management covers and route your TV cables along the arms of the bracket, leaving
slack around the joints and clip the cable management covers back on - see Diagram ‘G’.
2. To adjust the tilt there are two adjustment bolts located behind the TV mounting plate - see Diagram ‘H’.
Tighten the bolts enough using spanner ’K’ so the TV tilts freely but not on its own accord.
+8°/-5°
180°
Spanner K
180°
180°
Diagram ‘G’ Diagram ‘H’
Adjustment
bolts
TIP: When fitting the cable
management covers, make
sure to attach them as shown
in the illustration.
Troubleshooting:
Don't panic! In case of any issues with compatibility or for any advice on fitting, please contact our team at
help@InvisionTechnology.co.uk and we will help you overcome any problems. All our products carry our
Compatibility Promise.
Your installation is now complete - Sit back & enjoy!
To activate your 25 year warranty please email your name, order number
and product ref HDTV-M to warranty@InvisionTechnology.co.uk
4
