inVue Plunger Lock III User manual

Plunger Lock III
PL203

2 3
Review entire instruction guide before starting installation.
It may be necessary to remove cabinet doors to allow for
screw access and lock attachment.
Application
Plunger Lock III is designed for glass sliding panel doors
with an existing hole ranging from 22 mm – 32 mm (0.87”
– 0.26”). Reference Cabinet Requirements on pages 4
and 5.
Cabinet Specification
Glass bypass panels with a thickness range of 5.8 mm –
10 mm (0.23” – 0.4”).
System Components
1. Plunger Lock III (PL203)
2. IR2 Key (PK4400)
Setup in 4 easy steps:
1. Gain access to front and back of front panel and
mounting hole
2. Place Plunger Lock body into hole
3. Align back plate with lock from back side of panel
4. Attach plate to Plunger Lock body using 4 screws
provided
Caution:
Wear appropriate safety gear (gloves and eye protection)
when working with and around glass panels.
Overview
!
Plunger Lock III
PL203
IR2 Key
PK4400

4 5
Hole Diameter
22 mm – 32 mm
(1.18” – 1.26”)
CABINET REQUIREMENTS CABINET REQUIREMENTS
X = Plunger Length = 23.5 mm (0.91”)
Y = Panel Thickness & Panel Gap must be 20.5 mm (0.81”) or less
Z = Panel Thickness: 5.8 mm – 10 mm (0.23” – 0.4”)
Note: If “Y” is greater than 20.5
mm (0.81”) but less than 24.5 mm
(0.96”), then plunger extension is
required. Attach extension when
plunger is extended using small
screw provided.
YX
Z
Plunger Extension
4 mm (0.15”)
3 mm (0.12”)
Plunger Lock TOP VIEW

6 7
Optional. The lock is sized to fit a 22 mm – 23 mm hole.
To install lock into larger hole (24 mm - 32 mm) use the
appropriate spacer (included).
2
(0.95”)
24 mm
(1.10”)
28 mm
(1.02”)
26 mm
(1.18”)
30 mm
Determine if front panel is on right or left hand side.
Note: The illustrations in this booklet are for right
front panel orientation. For left front panel cabinet
install in opposite direction.
1
Right Front Panel
Left Front Panel
22 mm ≤ hole size < 24 mm: No spacer required
24 mm ≤ hole size < 26 mm: 24 mm spacer
26 mm ≤ hole size < 28 mm: 26 mm spacer
28 mm ≤ hole size < 30 mm: 28 mm spacer
30 mm ≤ hole size < 32 mm: 30 mm spacer

8 9
Rotate back plate until holes on back plate align and
seat with screw holes on Plunger Lock.
4
Back
Plate
Slide Plunger Lock through hole in front panel.
3

10 11
Close cabinets before testing lock operation.
6
Using screws provided, alternate tightening screws to
ensure proper fit.
Note: #1 Phillips screwdriver with magnetic tip recommended.
5

12 13
LOCK STATUS INDICATORS
Locked
Unlocked
Error (not fully locked)
Note: Unlock lock, ensure
panels are fully closed and
try again.
Position IR2 Key against lock, push button and wait for
“beep” before removing key. Lock and unlock product
several times to ensure proper operation.
IR2 Key must be charged
and activated. See IR2 Key
instruction guide.
Hold until you get a
confirmation “beep.”
Note: If double “buzz,” an
error has occurred. Unlock,
ensure panels are fully
closed and try again.
Locked
7
“BEEP”
Press Here

© 2012 InVue Security Products Inc. All rights reserved.
InVue is a registered trademark of InVue Security Products.
SD0140 Rev0 10/08/12
www.invuesecurity.com
Corporate Office (North America) // 704.752.6513 •888.55.INVUE
Europe, Middle East & Africa // +31.23.8900150
Asia Pacific // +852.3127.6811
Latin America // +52.55.9000.3957