IonGear 5637 User manual
InstructionDisclaimer
Dennis Kirk provides instructions to help our customers better understand how to install the
products we sell. The instructions are exact copies of what the manufacturer includes with the
product being sold.
That means the quality and accuracy of the instructions is solely dependent on what the
manufacturer produces. We do our best to make the text legible and the pictures viewable.
However, the end result depends largely on the quality of instructions the manufacturer
provides.
Therefore, you will find that some instructions are not of the highest quality. Sometimes text is
hard to read and pictures are not easy to see. At times you will find the overall look of the
instructions to be less than professional. However, we feel it is better to provide what we have
rather than provide nothing at all.
To the best of our knowledge the instructions and application information contained in the
instructions is accurate. However, Dennis Kirk assumes no liability related to any errors that
may be contained in the copy of the manufacturer’s instructions we provide. Buyers are solely
responsible to insure that product use is consistent with their application.
800-969-7501 so we can further assist you regarding additional product information or any other
business related questions.
Thank you for doing business with Dennis Kirk.
Contents
(1
Pair) 10nGear™ Battery Powered Heating Gloves (Sizes:
SIM
or LlXL)
(1
Pair)
Li
-Ion Batteries with Integrated Temperature Controll
er
(1) Battery Charger
Getting Started
1) Charging the B
at
teries
-Connect the
10
nGear™ batteries to the
ACIDC
charger and plug the charger into
any stan
dar
d electrical outlet
- The batteries must continuously charge f
or
approximately four hours during its
initial charge period
-
The
LED light on the charger will indicate green when each battery is fully
charged
PLEASE
NOT
E
THAT
IT IS
OK
TO
CHARGE BOTH B
ATT
E
RI
ES
AT
THE
SAME TIME. THE CHARGER HAS
SEPARA
TE INDICATOR
LI
GHTS
FOR
EACH
BATTER
Y.
Page 1 of 4
10nGear™ Glove Battery Specifications
Voltage 7.4V
Capacity 2200mAh
Input DC8.4V 1200mA
Output LED Settings 100% -25% (high-low)
Efficiency
of
Output Power > = 98%
Expected Battery Life 500 charge cycles
Approvals CE, FCC
Country
of
Origin China
2) Connecting the System
Once fully charged, insert the battery/controller into the reinforced battery pocket
on the back ofthe glove gauntlet
Orient the battery so that the green controller plate
is
visible through the plastic
window
The POWER button can appear at the top or bottom of the plastic window
depending
on
your preferred orientation
Reach into the pocket and insert the connector into the battery (It may be easier
to pull the connector wire out and insert it into the battery BEFORE inserting it
into the pocket.)
3)
Using the 10nGear™ Battery Powered Heating Gloves
Please note that the battery will not turn on unless the connector has been fully
inserted into the battery
After connecting the glove to the battery/controller, push the "POWER" button to
turn
on
the system
Users can adjust the internal glove temperature settings by pressing the
"POWER" button
The temperature settings will cycle downward as follows:
100% ----7 75% ----7 50% ----7 25% ----7 OFF -100%
10nGear™ Glove Temperature &Battery Duration Specifications
Approximate Duration
SETTING
Temperature
on
Full Charge
100% 135D
F/5rC
3 hours
75% 120DF/49°C 4 hours
50% 105D
F/41
DC 6 hours
25% 90D
F/32°C 10 hours
Page 2 of 4
To turn the battery/controller off, press the "POWER" button using the cycle
outlined above or disconnect the glove from the battery
4) Re-charging the Battery
Remove the battery from the glove, connect it to the AC/DC charger and plug the
charger into any standard electrical outlet
Charging is complete once the LED indicates green
Washing
To wash this product, first remove the battery/controller unit
-The gloves can
be
hand washed and hung to dry
Users must ensure that the gloves are 100% dry before reconnecting the battery
-To clean the Battery/Controller unit, wipe with a dry cloth
Battery Storage
Store the battery/controller
in
a cool, dry area
-Avoid extended exposure to direct sunlight
Re-charge after long periods of non-use
Precautions
Read and follow all "Operating Instructions" prior to using this product
Stop using this product immediately if it becomes damaged or
is
found to
be
defective
Do not attempt to disassemble the Battery/Controller Unit or the Heating Glove
If the Battery/Control Unit is broken, cracked or ruptured, avoid contact with skin
and discard immediately
Discontinue use immediately if the Battery Powered Heating Gloves become
uncomfortably hot
Keep out
of
reach of children
If Battery Powered Heating Glove is torn, ripped or otherwise damaged, contact
the manufacturer to discuss repairs and/or future safety issues
Contact us if you have any questions
on
the safe use of this product
Other lonGear™ Products
Battery Powered
Heating Vest
Page 3 of 4
This manual suits for next models
1
Table of contents
