IPAS 61111 Series Service manual

BMA_6111x_Barchetto_en_Rev3 IPAS GmbH, Hölscherstraße 27, D-47167 Duisburg [e-mail]
Operating and mounting instructions
Barchetto 2 /4 /6 (LED optional)
Order No.: 61111-XX, 61112-XX
General usage
KNX control panels of the IPAS Barchetto product range can be used
for all standard switch and configuration functions via the KNX bus.
The functions switching, dimming, value setting, blinds and sun
protection, fan levels, and much more can be implemented with 2, 4
and 6 buttons.
Barchetto 4 Barchetto 6
Barchetto design buttons are designed for the installation of door
frames and can be mounted in thin-walled cut-outs with a material
thickness of 2-4 mm. The clamping springs located on the housing fix
the panel in the mounting cutout. Special sheet steel mounting boxes
are available for wall installation.
The KNX bus coupler is directly integrated into the device. A standard
bus terminal is used for the connection. Programming LEDs and
programming buttons are accessible on the back of the panel.
Device types and accessories
The following Barchetto devices and accessories are available:
Product
Description
Order-No.
Barchetto 2
Control panel
61111-02
Barchetto 2 with LED
Control panel
61112-02
Barchetto 4
Control panel
61111-04
Barchetto 4 with LED
Control panel
61112-04
Barchetto 6
Control panel
61111-06
Barchetto 6 with LED
Control panel
61112-06
Wall box for Barchetto 2-4
Accessories
61993-00
Wall box for Barchetto 6
Accessories
61994-00
Scope of delivery
The following individual components are part of the
Barchetto delivery package:
- Complete device with plugged in bus connector (KNX)
- Operating and mounting instructions
- Delivery in unbreakable individual packaging
Application program
Barchetto design panels are programmed with the following ETS
project application:
ETS_61112_Barchetto_V1.0.0.knxproj
Installation advice
Danger to life from electric current.
•The device must only be installed and commissioned by an
accredited electrical engineer.
•Please follow country-specific safety and accident
prevention rules!
•The device is intended for interior installation in dry rooms.
•For the installation, the device must be switched to zero
potential.
•Do not open the device! Faulty devices must be returned to
the manufacturer.
•Please follow country-specific rules and regulations for the
planning and construction of electrical installations.
Technical data
CONNECTION DATA
Power supply
Supply Voltage:
Consumption:
via KNX Bus
24V/40mA (approx. 1W)
Connectors
KNX: (black/red), TP
0,6...0,8mm solid
GENERAL DATA
Control and
display elements
KNX function keys:
Programming button:
LED, red:
Depending on the model,
2, 4 or 6.
To assign the physical
address.
Displays addressing mode.
Mechanical data
(Depending on the
model)
Casing:
Width:
Height:
Length:
Weight:
Mounting:
Metal/Plastic
40 mm
37 mm
130 mm (Barchetto 2/4)
178 mm (Barchetto 6)
Depending on the model
Clamped in the cutout or
using a universal wall box.
Electrical safety
Pollution class:
Protection type:*
Protection class:**
Overvoltage
category:
KNX Bus:
2
IP20
III
III
SELV DC 30V
EMC
requirements
Complies with:
EMC directive 2014/30/EU
Environmental
conditions
Weather resistance:
Environmental con-
ditions in operation:
Storage temperature:
Transportation
temperature:
Rel. humidity:
(non condensing)
EN 50090-2-2
-5°C to +45°C
-25°C to +55°C
-25°C to +70°C
5 % to 93 %
Approbation and
CE-Signage
KNX registered:
According to EMC-
Guidelines:
No
(Residential and
commercial buildings),
Low Voltage guidelines.
* (according to EN 60529); ** (according to IEC 1140)

BMA_6111x_Barchetto_en_Rev3 IPAS GmbH, Hölscherstraße 27, D-47167 Duisburg [e-mail]
Location and function of the display and control elements
Control elements:
Programming button and programming LED:
Mounting
Mounting in cutouts:
In cutouts with a material thickness of 2-4 mm, our control panels are
simply clamped in the cutout. The clamping springs attached to the
housing fix the panel in the mounting cutout.

BMA_6111x_Barchetto_en_Rev3 IPAS GmbH, Hölscherstraße 27, D-47167 Duisburg [e-mail]
Panel cut-out Barchetto 2/4: 102x34mm
Panel cut-out Barchetto 6: 148x34mm
Mounting in installation boxes:
Before mounting in the installation box, the bus cable is first connected
to the bus terminal and plugged into the corresponding terminal
receptacle on the rear of the device. Please note that the physical
address of the KNX device is then assigned. The programming button
required for address assignment and the programming LED are no
longer accessible after installation.
Due to the small tolerances, the functional installation of the design
panel into the wall mounting box requires a vertical and horizontal
installation of the mounting box into the wall.
Ordering data for Barchetto wall boxes:
Barchetto 2/4: 61993-00
Barchetto 6: 61994-00