IPCamPower IPCP-8P2G-AF2 User manual

USER GUIDE
PoE & Optical Transmission
Statement
1 PoE switch
1 Power Cord / Adapter
1 Mounting Kit
1 User Guide
Copyright © 2018 IPCamPower.com
This document contains proprietary information that is protected by copyright. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written
permission of Our company.
The information and product specifications within this document are subject to change at any time, without notice and
without obligation to notify any person of such change.
Packing List
Product overview
Product Introduction
The IPCP-8P2G-AF2 is a business class PoE switch that was designed for IP Camera Systems that utilize 8 IP cameras
or less. This switch has 8 10/100 PoE powered ports with 2 additional 10/100 non-powered Uplink ports. The AF2 model
has the ability to push up to 30 watts on each of the 8 PoE ports, with a total budget of 130 watts.
Features
Technical Structure and Port Description
AC/ IN 100- 240V
279 mm
44mm
210mm
A
D
C
3 5 7
2 4 6 8
1
9
10
Power
100M Act/ Link
100M
100M Act/L ink
PoE
B
8 Ports 100M + 2 Ports Ethernet 100M Uplink PoE Switch
9
10
Power
A. PoE Powe r Por t
B. Up-lin k 10/100M Ether net P ort
C. Power Wor kin g Status Lig ht
D. 100-24 0VAC, 50/60Hz
PoE
Comply to IEEE802.3, IEEE802.3u, IEEE802.3af, IEEE802.3at standards;
(8) 10/100 PoE powered ports; (2) 10/100M uplink ports
All ports support auto-flip (Auto MDI/MDIX);
Each PoE port can provide power up to 30W, Total budget of 130W;
Supply power for powered devices compatible with IEEE802.3af;
Suppo rt IEE E802.3x f ull duplex flow control and duplex bac kpressure flo w control;
backp lane b andwidt h: POE31108P:3.2G;
MAC address: POE31108P:8K;
Its 2KV network port surge protection can adapt to harsh outdoor environment;
Under the temperature of -20 ~ 75℃

!Note：Please confirm that the all the PD devices are complying with IEEE802.3af standard.
PoE Priority: This function will protect the switch when it is overloaded, if all devices consumption are higher than specified, switch
ports will be sorted by priority, Port 1, Port 2, Port 3, etc. Then the power supply of lowest priority will be turned off.
Power Plug / Adapter: Please only use the included power supply as the switch may be damaged if mismatched power is applied.
PoE Port Indicator Lights: There are indicator lights on the front panel that will show you if the switch is supplying power to a PoE
capable device.
Network Traffic Indicator Lights: There are lights on the front panel that will show if your plugged in device is
transmitting / receiving network data at an appropriate rate.
Indicator description:
!
Installation guide
Please install with the supporting devices.
Installation
Please co nfirm the following th ings before installation:
1. If the POE ports meets the power requirement of the connecting devices.
2. If the POE standard requirements and power supply matches with the power receiving device
(1/2+3/6-( End -span))
3 .If the output power of the matched p ower adapter is compatible with the specifica tion in the label of the POE s witch
Please in stall the POE switch acc ording to the following steps:
1. Put the PoE switch on the surface of a l arge and stable table.
2. Plug the p ower adapter into the po wer connector, and then connect the power outle t through the power cord.
3.
Connect the network devices to the POE switch port with network cable.
1.Please do not put heavy products on the POE sw itch, and please ensure good ventilation enviro nment for the POE switch.
2.Please cut off the power first before plug ging the power adapter.
Power
Connect the power cable, pl ug it into power socket, turn on the power, then the swi tch will automatically initialize,
and LED lights status will display as following:
1 All lights will flash brightly except for the PoE ports, which means a successful power boot has occured.
2 Power LED remains lit.
If initia lization is inconsistent with the above, please check the power.
Note
!Note
Connection Diagram Model Descriptions and Installation
IPCP-8P2G-AF2:8x 10/100M ports +2x 10/100 M Uplink port PoE switch, 1-8 port supports PoE, IEEE 802.3af, has the ability to
push up to 30 watts per port, with a total budget of 130W, network port transmission distance is 100m
Wide Are a Netwo rk
3 5 7
2468
1
G1
G2
8 Port 100M + 2 Ports Ethernet Gigabit Uplink PoE Switch
Power
1000M Act/Link
1000M
PoE
100M Act/Link
PoE
Indicator Status Description
Power Indicator : PWR
Green LED ON
Normal
PoE Indic a tor: PoE
100/1000M I ndicator:
Act/Link
OFF Power OFF
Green LED ON Connected PD, working properly
Green LED Blink Short circuit or current overload
OFF No Connected PD or Power OFF
Yellow LED Blink Data transmission properly
Yellow LED ON Connected with 10Mbps or 100Mbps network device
OFF No connected network device
Green LED ON Connected with 1000Mbps network device
OFF Connected with 10/100Mbps network device
SPD Indicat or: 1000M
Green LED ON Connected with 100Mbps network device
OFF Connected with 10Mbps network device
SPD Indicat or: 100M
Power