ipf electronic PSQ80076 User manual

MANUAL • Subject to alteration! Version: June 2022
ipf electronic gmbh │ Rosmarter Allee 14 • 58762 Altena • Germany │ Tel [phone] • [e-mail] •www.ipf-electronic.com 1
068-15018
PSQ80076 – PEQ80376
Laser-Through-beam sensor transmitter
Plastic housing, compact design
Setting by teach-in
LED display with setting guide
M8-connector 4-pole
Technical data
Range 4,000mm
Operating voltage 10 … 30V DC
Current consumption (Transmitter) ≤ 12mA
Current consumption (without load, receiver) ≤ 12mA
Output current (max. load) ≤ 50mA
Output signal PNP, no/nc
Response / release time ≤ 0.125 ms
Switching frequency 4kHz
Transmitting element (clocked) Laser diode, red light, pulsed
Light spot size see diagram
Wavelength 655nm
short-circuit proof +
reverse polarity protected +
Display (operation) LED green (LED 1)
Display (signal) LED yellow (LED 2)
Material (housing) Plastic (PUR)
Material (front panel) PMMA
Protection class (EN60529) IP 67
Ambient temperature -20 … +50°C
Connection M8-connector 4 pin
Connection accessories e.g. VK200375
Mounting accessories (universal holder) AY000116
Electrical connection transmitter Electrical connection receiver
Laser protection class 1
brown
white
black
blue
brown
white
black
blue

MANUAL • Subject to alteration! Version: February 2022
2 ipf electronic gmbh │ Rosmarter Allee 14 • 58762 Altena • Germany │ Tel [phone] • [e-mail] •www.ipf-electronic.com
Dimensional drawing Light spot size
Safety instructions
Read the operating instructions before commissioning.
Connection, installation, adjustment and commissioning may only be performed by qualified personnel.
The device must not be used outdoors. Laserschutzklasse 1; Wellenlänge: 655nm; Frequenz; 5kHz, Pulsbreite: 3,2µs;
Grenzwert Puls: ≤ 2,3mW (IEC 60825-1)
Complies with 21 CFR 1040.10 and 1040.11 except for deviations as specified in Laser Notice No. 56, May 2019.
Attention! Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure
Before commissioning, please make sure that all safety instructions in the product documentation, if applicable, have
been observed!
Not a safety component according to the EU Machinery Directive. The use of these products is prohibited if they have
a direct impact on personal safety.
Intended use
The sensor is used for optical non-contact detection.
Connection
Plug the connector onto a suitable cable socket in a voltage-free manner and screw it tight.
Connect the cable according to the connection diagram on page 1.
As soon as the operating voltage is applied, the green LED (LED 1) lights up.
Information on the connection of the white line (PIN 2):
1. Receiver: Connection with L+: Teach in analog to the respective specifications for the keystroke
Connection with L-: Teach button locked
No connection: Normal operation - it is recommended to connect the line to a free terminal
during normal operation.
2. Transmitter:Connection with L+: Laser diode off
Connection with L- / no connection: Normal operation - it is recommended to connect the line
to a free terminal during normal operation.
Mounting
Mount the sensor on a suitable holder (e.g. universal holder AY000116).

MANUAL • Subject to alteration! Version: June 2022
ipf electronic gmbh │ Rosmarter Allee 14 • 58762 Altena • Germany │ Tel [phone] • [e-mail] •www.ipf-electronic.com 3
Adjustment
Align the transmitter and receiver so that the transmitter beam hits the receiver element straight on.
Switching mode
N.O. = normally open
N.C. = normally closed
Setting
The light barrier is set via teach-in on the receiver. You can teach-in via the key or by connecting the white line to L+
instead of pressing the key.
Standard teach in:
Is suitable for almost any application. The adjustment is made to the free light beam and the object.
Step 1: Teach in the light barrier. Step 2: Teach in object.
Press the key > 3s on the receiver, Press the key > 1s on the receiver.
until the green and the yellow LED simultaneously
flashing. Release the key, the LEDs flash
alternately.

MANUAL • Subject to alteration! Version: February 2022
4 ipf electronic gmbh │ Rosmarter Allee 14 • 58762 Altena • Germany │ Tel [phone] • [e-mail] •www.ipf-electronic.com
Dynamic teach in:
Is suitable to adjust the sensor in the running process, especially for small objects.
Step 1: Step 2:
Press the key > 3s on the receiver, On the receiver, press the key for the duration
until the green and the yellow LED simultaneously of a cycle.
flashing. Release the key, the LEDs flash
alternately.
Switching N.O. / N.C. (on the receiver)
→N.O. →→N.C. →…
Press the key for >
13s until the green
and yellow LEDs flash
rapidly alternately.
green LED flashes
yellow LED lights up
↓
wait 10s↓
Press key shortly
Green LED flashes
Yellow LED is off
↓
wait 10s
↓