Ironton 37809 User manual

1250 LB. CAPACITY
MECHANICAL WHEEL DOLLY
OWNER'S MANUAL
WARNING:
Read carefully and understand all
INSTRUCTIONS
basic safety precautions may result in serious personal injury.
ASSEMBLY AND OPERATION
before operating. Failure to follow the safety rules and other

Thank you very much for choosing a IRONTON product. For future reference,
please complete the owner's record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire manual
to become familiar with this product before you begin using it.
This machine is designed for certain applications only. The distributor cannot be responsible for
distributor to determine if it can or should be performed on the product.
relative to a particular application, DO NOT use the machine until you have first contacted the
issues arising from modification. We strongly recommend this machine not be modified and/or
used for any application other than that for which it was designed. If you have any questions
For technical questions please call 1-800-222-5381.
TECHNICAL SPECIFICATIONS
Weight Capacity 1250 lb.
Maximum Tire Width
Capacity 10"
Distance Between
Rollers (Center to
Center)
13-1/2” (Minimum)
28-3/4” (Maximum)
Weight 38.8 lb.
GENERAL SAFETY RULES
WARNING:Read and understand all instructions. Failure to follow all instructions listed
below may result in serious injury.
CAUTION:Do not allow persons to operate or assemble this merchanical wheel dolly
until they have read this manual and have developed a thorough understanding of how the
merchanical wheel dolly works.
WARNING:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could occur. It must be
understood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
Page 2

Inspect before every use; do not use 10.
if parts are loose or damaged.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
Keep work area clean. Cluttered areas invite injuries.
Observe work area conditions. Do not use machines or power tools in damp
or wet locations. Don’t expose to rain. Keep work area well lighted.
Keep children away. Children must never be allowed in the work area.
Store idle equipment. When not in use, this product must be stored in a dry
location to inhibit rust.
Use the right product for the job. Do not attempt to force a small product
or attachment to do the work of a larger industrial product. There are certain
applications for which this product was designed. It will do the job better and
more safely at the rate for which it was intended. Do not exceed weight capacity
Use eye and ear protection. Always wear ANSI-approved impact safety
goggles and dust mask or respirator when working around metal, wood, and
chemical dusts and mists.
Do not overreach. Keep proper footing and balance at all times.
1.
2.
3.
4.
5.
6.
7.
Page 3
of 1250 lb. rated rated capacity. Do not modify this product and do not use this
product for a purpose for which it was not intended.
Maintain product with care. Keep product clean for better and safer
performance.
Stay alert. Watch what you are doing, use common sense. Do not operate any
product when you are tired.
Check for damaged parts. Before using any product, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving
parts; any broken parts or mounting fixtures; and any other condition that may
affect proper operation. Any part that is damaged should be properly repaired
or replaced by a qualified technician.
8.
9.
10.
Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
11.

Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
Do not operate product if under the influence of alcohol or drugs. Read
warning labels if taking prescription medicine to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not operate
the product.
Warning:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
operator.
Unpacking
11.
12.
Page 4
ASSEMBLY
Use Nut (1) and Spring Washer (2) to 1.
fasten a Caster (3) to each of the Rod
Assemblies (4), the Outer Body Axle
Assembly (9) and the Inner Body Axle
Assembly (10). See the Parts Dia-
gram on Page 7 for reference.
Slide each Roller (8) over each Rod 2.
Assembly. See the Parts Diagram on
on Page 7 for reference.
Repeat Step 3, on with the Inner 4.
Body Axle Assembly (10), making
sure all connections are tightened
firmly.
Remove Lock Nut (5) and Bolt (6) 3.
from each Rod Assembly. Slide
Roller (8) and Washer (7) onto Rod
Assembly. Slide Rod Assembly into
square tube on Outer Body Axle As-
sembly (9). Fasten together using
Lock Nut and Bolt, making sure all
connections are tightened firmly.
When unpacking,check to make sure all parts listed on Page 7 are included.

OPERATION
IMPORTANT! BEFORE FIRST USE:
Thoroughly lubricate and test the •
Wheel Dolly for proper operation.
Position Dolly in front of tire and slide 1.
Latch (24) to right. Lift Lock Pin (17)
and rotate counterclockwise until tab
faces away from Pedal Arm (19). See
Figure 1.
Place hands on Rollers (8) and 2.
spread apart to tire width required.
Roll Dolly forward, centering Rollers 3.
against tire.
Slide Latch to left. Then turn Lock Pin 1.
clockwise until it retracts into ratchet.
Turn tab counterclockwise, keeping
it away from end of Pedal Arm. See
Figure 2.
Figure 1 Latch (24)
Lock
Pin (17)
Tab
Pedal Arm
(19)
Latch (24)
Pedal Arm
(19)
Figure 2
Tab
WARNING! 5. Before the vehicle has
been placed on all four Wheel Dol-
lies, ensure that you have sufficient
assistance and manpower to safely
guide and control the vehicle.
Stay clear of any sloping areas or 6.
entry ramps, however shallow they
may appear. Sufficient space should
be allowed between the side of the
vehicle and an adjacent wall for the
vehicle to be withdrawn from its loca-
tion in a sideways manner.
Place foot on Pedal and pump in full 2.
strokes, forcing the Rollers to come in
(closer together).
Continue raising the tire until it is ap-3.
proximately 3/4” off the ground.
If needed, raise every other wheel 4.
with its own separate Wheel Dolly.
WARNING! Be ready for any move-
ment the vehicle may make when
next wheel comes off the ground.
Page 5
LIfTING WHEEL

To lower the Wheel Dolly, slide the 1.
Latch counterclockwise (to the right).
Turn Tab clockwise, making sure it
aligns with the channel at the end of
the Pedal Arm. See Figure 3.
Push Pedal down and release.2.
Continue until tire fully rests on the
ground.
Keep Latch in right position.1.
Lift Lock Pin (17) and turn right 2.
(counterclockwise) until Tab faces
away from Pedal Arm.
Place hands on Rollers and spread 3.
them apart to clear tire.
Pull Dolly away from tire, retract 4.
Rollers, and turn Pin right to engage
ratchet. While keeping Tab away from
Pedal arm, push Pedal down and
lock in place with wire latch.
Latch (24)
Figure 3
Tab
Channel
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
LOWERING WHEELS
REMOVING DOLLY
Page 6

For technical questions, please call
PARTS LIST AND ASSEMBLY DIAGRAM
Part Description Q’ty
1 Nut M12 4
2 Spring Washer 12 4
3 Caster Assembly 4
4 Rod Assembly 2
5 Lock Nut M12 3
6 Bolt M12*55 2
7 Washer 4
8 Roller Assembly 2
9 Outer Body Axle Assembly 1
10 Inner Body Axle Assembly 1
11 Screw M6*10 1
12 Big Washer 6 2
13 Carry Head Assembly 1
Part Description Q’ty
14 Spring Ring 1
15 Bushing 1
16 Spring 1
17 Lock Pin 1
18 Spring Pin 4*16 1
19 Pedal Arm 1
20 Support Plate 1
21 Retaining Ring 8 2
22 Axis 1
23 Lock Nut M6 1
24 Latch 1
25 Retaining Spring 1
26 Bolt M12*80 1
Note: Some parts are listed and shown for illustration purposes only and are not avail-
able individually as replacement parts.
1-800-222-5381.
Page 7

limited 90 Day Warranty
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Northern Tool + Equipment Co., Inc. makes every effort to assure that its products meet high quality
Page 8
Distributed by
Northern Tool + Equipment Co., Inc.
Burnsville, Minnesota 55306-6936
NorthernTool.com
Made in China